Toshiba Strata Dk24, Dk56, Dk96 Instruction Manual

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY 1991 
TABLE 9-B 
STATION LOOP REQUIREMENTS 
Device Description 
PEKU 
(ckts 1 - 8) Electronic 
P%JZ telephone, 
door phone/ 
control boxes 
(ckts 5 - 8) 
PEKU 
(ckts 7 & 8) DSS consoles 
Max Loop Resistance 
Max Distance from 
(Including Device) 
KSU to Device 
40 ohms 1000 ft. (303 m) 
20 ohms 
500 ft. (152 m) 
Number of 
Wire Pairs 1 
All need 2-pair. 
EKTs which 
receive OCA 
calls need 
3-pair.’ 
PSTU Standard 
Approx. 3000 ft. (909 m)...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY 1991 
TABLE 9-D 
DIGITAL TELEPHONE/DIU/DDSS CONSOLE/LOOP LIMITS . 
PPSU 1 OOOft (303m) 1 OOOft (303m) 
DDSSI 060A 
Battery Backup 500ft (151m) 1 OOOft (303m) 
*Battery backup applies to instances when the system is being powered 
by batteries exclusively. 
9-2A  

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY1991 
This page is intentionally blank. 
9-2B  

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY1991 
BUILDING #l BUILDING #2 
TELEPHONE 
&I Secondary protectors 
PEMU  PEMU 
PCOU  PCOU 
1 I E&M TIE LINE 
CO LINE 
HtiUHt Y-A-StWNDARY PROTECTOR DIAGRAM 
IMPORTANT! 
To protect against transient voltages and currents, secondary protectors must be installed if 
there is outside wiring (Figure 9-A). These protectors, which contain fast semiconductors in 
addtion to fuses, shall comply with the requirements forsecondarypro tectors for communica...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY1991 
1. Certron Corp; Anaheim, California 92807 
l Secondary protector: Model 08450. 
2. Curtis Mfg. Co. lnc; Jaffrey, New Hampshire 03452 
l Secondary protector: Model Diamond Chip. For indoor use on the protected side of the 
telephone circuit only. 
3. Oneac Corp; Libertyville, Illinois 60048 
l Secondary protector: Model OnLine 614+ and OnLine DG/S. For indoor use on the 
protected side of primary telephone protector only. 
4. Siemon Co.;...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY 1991 
TO P 
C EKU W/FEMALE 
:ONNECTOR BRIDGING 
VOICE Tl 
DATA Ti 
DATA RI 
=+r CIRCUIT 4  1 654321 
R1  OCA 
Rl  STATION CABLE 
TWISTED PAIR  1 PAIR 
IG 
CIRCUIT 5 
NOTE: See Program 28 
for electronic telephone 
CIRCUIT 6 to DSS assignments. 
VOICE PAIR-NOT USED 
CIRCUIT 7 
DATA TIP 7 
DATA RING 7) 
I TELEPHONE 
IR-NOT USED ASSOCIATED 
WITH DSS/BLF ‘ATION 
CIRCUIT 3 ELECTRONIC 
TELEPHONE 
CIRCUIT 4 RECEIVES 
OFF-HOOK CALLS 
NOTE: Place 
PEKlJ...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY1991 
TO PEKU OR PESU 
W/FEMALE CONNECTOR BR’DG’NG 
/-I InP 
66M150 SPLIT BLOCK ’ CIRCUIT 5 
CIRCUIT 6 
CIRCUIT 7 
CIRCUIT 8 
NOT USED SCREW 
1654321 u uuun I I l”lYL n 
MDFB (REAR VIEW) 
( , ; 4 , / lDOO$--1 
I VR VT 
MDFB 
DOOR 
PHONE B 
OR DOOR 
LOCK 
CONTROL 
I I 
I 
See Note I l J 
See Note 2 
1 MDFB (DOOR PHONE) STATION #s 
See Note 3 
NOTES: 
26 1 161 1 162 1 163 
1. On PEKU or PESU, cut W9. See Programs 39, 
77-I. 77-2, and 79. 
2. HDCB...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY 1991 
TO PEKU W/FEMALE 
‘CONNECTOR BRIDGING STATION CABLING (24 AWG, TWISTED PAIRS) 
VOICE Tl (VT) 
1 VOICE RI (VR) 
DATA Tl (DT) 
DATA Rl (DR) 
J TO ELECTRONIC TELEPHONE 1 
(PORT 00) 
CIRCUIT 2 TO ELECTRONIC 
TELEPHONE (PORT 01) 
I. 
Available with R2 software only. 
BACKGROUND MUSIC 
\,R9 l!=mRT n3 - 
SOURCE OUTPUT 
(600 OHMS; 1 V RMS MAX) 
CAUTION: To avoid distortion, do not 
connect port 02 to 8-ohm outputs. 
PTRONIC 
.03)  CIRCUIT 4 TO...

INSTALLATION-WIRING DIAGRAMS 
SECTION 200-096-209 
FEBRUARY1991 
MDF BLOCK NO. DKSU SLOT NO. . 
NOTES: 
1. Indicate if BGM or electronic telephone is connected (see Program IO-2 and 19); BGM connects to VT 
and VR, circuit 3 only (DT and DR not used). 
2. Indicate if electronic telephone or HDCB (allowed HDCB port numbers: 04, 12, 20, 28). 
3. Indicate if electronic telephone or DSS no. 1, 2, 3, or 4. 
4. Copy for each PEKU installed. 
5. OCA wiring not shown, see MDF-to-electronic telephone wiring....