Toshiba Estudio 170f Manual

4949
The key touch tone volume can
be adjusted using the following
procedure.
Press:
MENU++++++
The current setting is displayed
on the bottom row.After completing this Configura-
tion Setting, you may continue
to select other volume settings
referring to their associated
pages for instructions, or press
STOP
to exit the Configuration Setting
mode and return to the Standby
Mode.
Enter the desired volume value
(1 to 8; 1 for maximum, 7 for
minimum, 8 for off).
or
Select the desired volume
value, using the...

50The line monitor volume can be
adjusted using the following
procedure.
Press:
MENU++++++
The current setting is displayed
on the bottom row.After completing this Configura-
tion Setting, you may continue
to select other volume settings
referring to their associated
pages for instructions, or press
STOP
to exit the Configuration Setting
mode and return to the Standby
Mode.
Enter the desired volume value
(1 to 8; 1 for maximum, 7 for
minimum, 8 for off).
or
Select the desired volume
value, using the...

5151
This function allows you to
minimize power consumption
by turning power off to portions
of the machine (as selected).
If the Power Saver function is
ON, a warm up period is
needed before printing occurs.
This facsimile has two Power
Saver modes, Super Energy
Saver and Printer Power Saver.
Super Energy Saver turns virtu-
ally all power off to minimize
power consumption. Select one
of three modes, Automatic,
Manual or OFF.
Printer Power Saver turns only
the fuser section off during the
time period...

52
After completing this Configura-
tion Setting, press
STOP
to exit the Configuration Setting
mode and return to the Standby
Mode.
Power Saver Operation - continued
Enable or Disable the Printer
Power Saver function.(to set  Printer Power Saver ON)(to set Printer Power Saver OFF)If “ON” is selected, the cur-
rently set time period is dis-
played below. The time on the
left is the Printer Power Saver
start time (or time that the
printer unit will power down).
The time on the right is the
Printer Power...

5353
Department Code Setting
Department Code operation is
used to monitor the facsimiles
activity when shared between
multiple users or workgroups.
This feature is especially useful
when billing departments based
on machine usage.
When Department Code opera-
tion is enabled, access to the
facsimile is restricted to 50
valid department code pass-
words.
Each department code will be
assigned a 5-digit department
code password. These pass-
words must be entered each
time a user wishes to send a
facsimile,...

54Department Code Setting - continued
After entering the Master De-
partment Code password, the
facsimile will prompt for an In-
dividual Department Code ad-
dress.
Select an Individual Depart-
ment Code address from 02 to
50.After selecting the Individual
Department Code address,
press:
Enter a 5-digit Master Depart-
ment Code Password using the
Dial Keypad. This password
will be required to gain supervi-
sor access to the machine.
Important: Record the pass-
word in a safe location so that
if it is...

5555
Department Code Maintenance
is used to cancel or change the
Master or Individual Depart-
ment Code.
This procedure can only be per-
formed by a supervisor who
possesses the Master Depart-
ment Code Password. Enter
this password before proceed-
ing.
Enable or Disable the Depart-
ment Code function.
(for YES-Enable)(for NO-Disable)
NOTE:Disabling Department
Codes will delete all
information related to
the Department Codes
stored.
If “NO” is selected, the “COM-
PLETED” message will be dis-
played, the...

56If you wish to continue, repeat
Steps 2 and 3.
After completing this Configu-
ration Setting, you may con-
tinue to select other settings
referring to their associated
pages for instructions, or press
STOP
to exit the Configuration Set-
ting mode and return to the
Standby Mode.
Select Another
SETUP Item, or ...
5Department Code Maintenance - continued 

5757
Enable or Disable Account
Codes.Select ON to enable Account
Code prompting and printing on
the Transmission Journal.Or, select OFF to disable Ac-
count Codes from being
prompted and printed on the
Transmission Journal.
This feature provides valuable
Account Code tracking informa-
tion for each facsimile trans-
mission sent from the unit.
When a facsimile is transmit-
ted, the account code number
will be recorded on the Trans-
mission Journal.Press:
MENU++++
After completing this Configu-
ration...

58Line Monitor Default Setting
This function is used to set the
speaker ON in order to monitor
every transmission.
This function is mainly used to
confirm dialing and phone line
status.Press:
MENU++++
Display the LINE
MONITOR Menu
1
To turn ON the monitor
speaker, press:To turn OFF the monitor
speaker, press:
Select the Line
Monitor Option
2
After completing this Configu-
ration Setting, you may con-
tinue to select other settings
referring to their associated
pages for instructions, or press
STOP
to...