Home > Toshiba > Copier > Toshiba Estudio 162 Owners Manual

Toshiba Estudio 162 Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Estudio 162 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							e-STUDIO162/162D/151/151D  DISASSEMBLY AND ASSEMBLY  8 - 18
    8. Power section
    A. List
    B. Disassembly procedure
    1) Disconnect each connector.
    2) Remove the screw, and remove the earth line.
    3) Remove two screws, and remove the power PWB unit.
    Caution: Be careful not to touch the sharp edge on the circumference
    of the metal frame for the power supply.
    C. Assembly procedure
    For assembly, reverse the disassembly procedure.
    9.Duplex motor section (Duplex model only)
    A. List
    B. Disassembly procedure
    1) Remove the rear cabinet.
    2) Remove two screws.
    3) Remove the Duplex motor cover.
    4) Remove the Duplex motor.
    Note: When reassembling, be sure to engage the Duplex motor gear
    with the belt on the main body side.
    C. Assembly procedure
    For assembly, reverse the disassembly procedure.
    10. Reverse roller section (Duplex model 
    only)
    A. List
    B. Disassembly procedure
    1) Remove four screws
    2) Remove the spring, and the earth wire
    3) Remove the reverse unit.
    4) Bend the reverse roller and remove it.
    C. Assembly procedure
    For assembly, reverse the disassembly procedure. No. Part name Ref.
    1 Power PWB
    No. Part name Ref.
    1 Duplex motor
    1)1)1)1)
    2)
    3)
    4)
    4)5)
    1)
    1
    23
    1
    No. Part name Ref.
    1 Reverse roller
    1 2
    3
    1
    08_DISSASEMBLY.fm  18 ページ  2004年12月23日 木曜日 午後1時8分 
    						
    							e-STUDIO162/162D/151/151D ADJUSTMENTS  9 - 1
    [9] ADJUSTMENTS
    1. Optical section
    A. Copy magnification ratio adjustment
    The copy magnification ratio must be adjusted in the main scanning
    direction and in the sub scanning direction. To adjust, use TC 48-01.
    (1) Outline
    The main scanning (front/rear) direction magnification ratio adjustment
    is made manually.
    The adjustment is made by manual key operations. (The zoom data
    register set value is changed for adjustment.)
    The magnification ratio in the sub scanning direction is adjusted by
    changing the carriage (scanner) scanning speed.
    (2) Main scanning/sub scanning direction magnification 
    ratio adjustment
    a. Cases when the adjustment is required
    1) When the main PWB is replaced.
    2) When the EEPROM in the main PWB is replaced.
    3) When U2 trouble occurs.
    4) When repairing or replacing the optical section.
    b. Necessary tools
    •Scale
    c. Main scanning direction adjustment procedure
    1) Set the scale vertically on the document table. (Use a long scale
    for precise adjustment.)
    2) Set the copy magnification ratio to 100%.
    3) Make a copy on A4 or 81/2 x 11 paper.
    4) Measure the length of the copied scale image.5) Calculate the main scanning direction magnification ratio. 
    Main scanning direction magnification ratio
    6) Check that the copy magnification ratio is within the specified
    range. If it is not within the specified range, perform the following
    procedures.
    7) Execute TC 48-01 to select the main scanning direction copy
    magnification ratio adjustment mode.
    To select the adjustment mode, use the [
    ←/→] key.
    8) Enter the new set value of main scanning direction copy
    magnification ratio with the copy quantity set key, and press the
    [START] key.
    9) Change the set value and repeat the adjustment until the ratio is
    within the specified range.
    When the set value is changed by 1, the magnification ratio is
    changed by 0.1%.
    d. Sub scanning direction adjustment procedure
    1) Set the scale on the document table as shown below. (Use a long
    scale for precise adjustment.)
    =Copy image dimensions
    X 100 (%)
    Original dimension
    ModeDisplay 
    itemDefault 
    valueLED
    Main scan direction 
    magnification ratioF-R 50 PRINT mode lamp
    OC mode sub scan 
    direction magnification ratioSCAN 50 SCAN mode lamp
    100 110 120130150140mm
    1/2mmJAPANHARDENED
    STAINLESS
    Shizuoka
    100110120130150140mm
    1/2mmJAPANHARDENED
    STAINLESS
    Shi zuoka
    110
    10 20
    1020
    (When a 100mm scale is used as the original.)
    Paper feed
    direction
    ReferenceComparison pointOriginal (Scale)
    Copy
    e-STUDIO162_151.book  1 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ADJUSTMENTS  9 - 2 2) Set the copy magnification ratio to 100%.
    3) Make a copy on A4 or 81/2 x 11 paper.
    4) Measure the length of the copied scale image.
    5) Calculate the sub scanning direction copy magnification ratio
    using the formula below.
    6) Check that the actual copy magnification ratio is within the
    specified range. (100 ± 1.0%).
    If it is not within the specified range, perform the following
    procedures.
    7) Execute TC 48-01 to select the sub scanning direction copy
    magnification ratio adjustment mode.
    To select the adjustment mode, use the [
    ←/→] key. (SCAN mode
    lamp ON)
    8) Enter the new set value of sub scanning direction copy
    magnification ratio with the copy quantity set key, and press the
    [START] key.
    Repeat procedures 1) - 8) until the sub scanning direction actual copy
    magnification ratio in 100% copying is within the specified range.
    When the set value is changed by 1, the magnification ration is
    changed by 0.1%.
    B. Image position adjustment
    The employed test commands and the contents are as follows:The modes can be selected by pressing [
    ←/→] key.
    (*): Support for the installation models. For non-installation models,
    skip.
    * In the 2nd print center offset adjustment, print is made forcibly as
    1to2/Long Edge from OC regardless of duplex setting.
    (1) Lead edge adjustment
    1) Set a scale to the center of the paper lead edge guide as shown
    below, and cover it with B4 or 8 1/2 x 14 paper or OC cover.
    2) Execute TC 50 - 01
    3) Set the print start position (A: COPY mode lamp ON), the lead
    edge void amount (B: PRINT mode lamp ON), the scan start posi-
    tion (C: SCAN mode lamp) to 1, and make a copy of the scale at
    100%.
    4) Measure the image loss (Rmm) of the scale.
    Set C = 10 x R (mm). (Example: Set to 40.)
    When the value of C is increased by 10, the image loss is
    decreased by 1mm. (Default: 50)
    5) Measure the distance (Hmm) from the paper lead edge to the
    image print start position.
    Set A = 10 x H (mm). (Example: Set to 50.)
    When the value of A is increased by 10, the image lead edge is
    moved to the paper lead edge by 1mm. (Default: 50).
    6) Set the lead edge void amount to B = 50 (2.5mm). (Default: 50)
    When the value of B is increased by 10, the void is extended by
    about 0.1mm. (For 25 or less, however, the void amount is
    regarded as 0.)
    * The ADF adjustment is made by adjusting the ADF image scan start
    position after OC adjustment. =Copy image dimensions
    X 100 (%)
    Original dimension
    ModeDisplay 
    itemDefault LED TC
    Print start position 
    (Main cassette paper 
    feed)TRAY1 50 COPY mode lamp
    Main cassette 
    lamp
    50-01 (*) Print start position 
    (2nd cassette paper 
    feed)TRAY2 50 COPY mode lamp
    2nd cassette lamp
    Print start position 
    (Manual paper feed)MFT 50 COPY mode lamp
    Manual feed lamp
    Image lead edge void 
    amountDEN-A 50 PRINT mode lamp
    Image scan start 
    position RRC-A 50 SCAN mode lamp
    Image rear edge void 
    amountDEN-B 50 COPY mode lamp
    PRINT mode lamp
    SCAN mode lamp
    100110 120130150140mm
    1/2mmJAPANHARDDENCD
    STAINLESS
    Shizuoka
    100110 120130150140mm
    1/2mmJAPANHARDDENCD
    STAINLESS
    Shi zuoka
    110
    1020
    10 20
    Original (Scale)
    Paper feed
    direction
    ReferenceComparison point
    Copy
    ModeDisplay 
    itemDefault LED TC
    Print center offset 
    (Main cassette paper 
    feed)TRAY1 50 COPY mode lamp
    Main cassette lamp
    50-10 (*) Print center offset 
    (2nd cassette paper 
    feed)TRAY2 50 COPY mode lamp
    2nd cassette lamp
    Print center offset 
    (Manual paper feed)MFT 50 COPY mode lamp
    Manual feed lamp
    2nd print center 
    offset (Main cassette 
    paper feed) SIDE2 50 PRINT mode lamp
    Main cassette lamp
    e-STUDIO162_151.book  2 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ADJUSTMENTS  9 - 3 (Example)
    (2) Image rear edge void amount adjustment
    1) Set a scale to the rear edge section of A4 or 11 x 8 1/2 paper size
    as shown in the figure below, and cover it with B4 or 8 1/2 x 14
    paper.
    2) Execute TC 50 - 01 to select the image rear edge void amount
    adjustment mode.
    The set adjustment value is displayed on the copy quantity display.
    3) Make a copy and measure the void amount of image rear edge.
    4) If the measurement value is out of the specified range, change the
    set value and repeat the adjustment procedure.
    The default value is 50.
    (3) Center offset adjustment
    1) Set the self-made test chart for the center position adjustment so
    that its center line is aligned with the center mark of the document
    guide.
    •Test chart for the center position adjustment.
    Draw a line at the center of A4 or 8 1/2 x 11 paper in the paper
    transport direction.2) Execute TC 50-10 to select the print center offset (cassette paper
    feed) adjustment mode.
    The set adjustment value is displayed on the copy quantity display.
    3) Make a copy and check that the copied center line is properly
    positioned.
    The standard value is 0 ±2mm from the paper center.
    4) If the measured value is out of the specified range, change the set
    value and repeat the adjustment procedure.
    When the set value is increased by 1, the copy image is shifted by
    0.1mm toward the rear frame.
    •For the manual paper feed, change the manual paper feed
    adjustment mode and perform the similar procedures.
    •Since the document center offset is automatically adjusted by the
    CCD which scan the reference lines (F/R) on the back of document
    guide, there is no need to adjust manually.
    2. Copy density adjustment
    A. Copy density adjustment timing
    The copy density adjustment must be performed in the following cases:
    •When maintenance is performed.
    •When the developing bias/grid bias voltage is adjusted.
    •When the optical section is cleaned.
    •When a part in the optical section is replaced.
    •When the optical section is disassembled.
    •When the OPC drum is replaced.
    •When the main control PWB is replaced.
    •When the EEPROM on the main control PWB is replaced.
    •When the memory trouble (U2) occurs.
    B. Note for copy density adjustment
    1) Arrangement before execution of the copy density adjustment
    •Clean the optical section.
    •Clean or replace the charger wire.
    •Check that the voltage at the high voltage section and the
    developing bias voltage are in the specified range.
    5mm
    10mm
    Distance from the paper lead edge 
    to the image lead edge, H = 5mm
    Image loss, R = 4mm
    B4 or 8 1/2″ × 14″ paper
    A4 size rear edge
    Scale image
    Paper rear edge Void amount (Standard value: 2 - 3mm)
    Document guide
    (Copy A)
    (Copy B)2.0mm or less
    2.0mm or less
    Copy image
    Copy paper
    folding line
    Copy image
    Copy paper
    folding line Shift
    Shift
    (Paper feed direction)
    e-STUDIO162_151.book  3 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  ADJUSTMENTS  9 - 4
    C. Necessary tool for copy density adjustment
    • One of the following test charts:
    KODAK GRAY SCALE
     B4 (14 x 8 1/2) white paper
     The user program AE setting should be 3.
    Test chart comparison table
    D. Features of copy density adjustment
    For the copy density adjustment, the image data shift function provided
    in the image process LSI is used.
    List of the adjustment modes
    E. Copy density adjustment procedure
    The copy density can be adjusted in 300dpi or in 600dpi.
    For selection of modes, use the copy mode select key.
    (1) Test chart (UKOG-0162FCZZ) setting
    1) Place the test chart so that its edge is aligned with the A4 (Letter)
    reference line on the document table. Then place a A4 (14 x 
    8 1/2) white paper on the test chart and close the document cover.
    (2) Perform the adjustment in each mode.
    1) Execute TC 46-01 (300dpi). To adjust in 600dpi, execute TC 46-
    02. 
    2) Select the mode to be adjusted with the exposure mode select key.
    Set the exposure level to 3 (center) for all adjustment. (Except for
    the auto mode.)
    (e-STUDIO151/151D (Europe))
    (e-STUDIO162/162D)
    3) Make a copy.
    Check the adjustment level (shown in the above table) of the
    exposure test chart (TOSHIBA Gray Scale).
    (When too bright): Decrease the value displayed on the copy quantity
    display.
    (When too dark): Increase the value displayed on the copy quantity
    display.
    * The value can be set in the range of 1 - 99. KODAK
     GRAY
     SCALE123419A
    Auto Mode Brightness 1 step only
    Manual Mode Brightness 5 steps. Adjustment of only the center 
    brightness is made.
    Photo Mode Brightness 5 steps. Adjustment of only the center 
    brightness is made.
    Manual T/S 
    modeBrightness 5 steps. Adjustment of only the center 
    brightness is made.
    T/S Auto mode Brightness 1 step only
    Main code Sub code Resolution for copy density adjustment
    4601 300dpi
    02 600dpi
    White paper
    Test chartTest chart
    Adjustment 
    modeDisplay 
    itemLEDTOSHIBA gray 
    chart adjustment 
    level
    Auto mode AE COPY mode lamp 3 is slightly 
    copied.
    Text mode TEXT PRINT mode lamp 3 is slightly 
    copied.
    Photo mode PHOTO SCAN mode lamp 3 is slightly 
    copied.
    Text T/S mode TSTXT PRINT mode lamp
    SCAN  mode lamp3 is slightly 
    copied.
    Auto T/S mode TSAE COPY mode lamp
    SCAN  mode lamp3 is slightly 
    copied.
    (2) Mode select key
    TEXT
         | | | | |(1) Exposure mode, level display
    112222111,2,3,
    1,2,3,SP. FUNCAUTOZOOMOK
    (2) Mode select key
    TEXT
         | | | | |(1) Exposure mode, level display
    09_ADJUS.fm  4 ページ  2004年12月22日 水曜日 午後2時39分 
    						
    							e-STUDIO162/162D/151/151D  ADJUSTMENTS  9 - 5
    3. High voltage adjustment
    A. Main charger (Grid bias)
    Note:
    • Use a digital multi meter with internal resistance of 10M
    Ω or more
    measurement.
     After adjusting the grid LOW output, adjust the HIGH output. Do not
    reverse the sequence.
    Procedures
    1) Set the digital multi meter range to DC700V.
    2) Set the positive side of the test rod to the connector CN11-3
    (GRID) of high voltage section of the power PWB and set the
    negative side to the frame ground (power frame).
    3) Execute TC 8-02. (The main charger output is supplied for 30 sec
    in the grid voltage HIGH output mode.)
    4) Adjust the control volume (VRG1) so that the output voltage is 580
    ±12V.
    B. DV bias check
    Procedures
    1) Set the digital multi meter range to DC500V.
    2) Set the positive side of the test rod to the connector CN-10-1 (DV
    BIAS) and set the negative side to the frame ground (power
    frame).
    3) Execute TC 25-01 to output the developing bias for 30sec, and
    check that the output is –400±8V.
    4. Duplex adjustment (With optional RADF 
    installed)
    A. Adjusting the paper reverse position in memory 
    for duplex copying
    This step adjusts the front surface printing (odd-number pages of a
    document set) in the S-D mode copying and the leading edge position
    of an image on even-number pages in the D-S mode.
    That is, it covers the adjustment of the second surface printing mode
    (image loss at the front edge of an image) in which image data is once
    stored in memory.
    The image data is read, starting from its front end in the document
    delivery direction (Reference direction of document setting in the OC
    mode)and stored in memory.
    This stored image data is printed starting at the printing start position,
    in the order of last-stored data to the first-stored data.
    In other words, the front edge image loss of the image can be adjusted
    by changing the document read end position.
    (Adjustment procedure)
    1) Preparing test chart (Draw a scale at the rear end of one side of a
    sheet of A4 white paper or letter paper)
    2) Set the test chart so that the scale is positioned as shown below, in
    the S-D mode and the D-S mode.
    3) Execute test command 50-18.
    Select the ADF memory reverse output position, and press
    [START] key to make a copy.
    Adjust the setting so that the front edge image loss is less than 4.0
    mm in the R-ADF mode.
    An increase of 1 in setting represents an increase of 0.1 mm in
    image loss. Note:  A digital multi meter with internal resistance of 1G
    Ω must be
    use for correct check.
     The adjustment volume is locked, and no adjustment can be
    made.
    VRG1
    Caution:
    Be careful not to touch the sharp
    edge on the circumference of the
    metal frame for the power supply.
    VRDV
    Caution:
    Be careful not to touch the sharp
    edge on the circumference of the
    metal frame for the power supply.ModeDisplay 
    itemDefault LED
    OC memory reverse 
    output position OC 50 COPY mode lamp
    ADF memory reverse 
    output positionADF 50 PRINT mode lamp
    510
    Scale (S-D mode) Scale (D-S mode)
    510
    The front edge of the
    scale on test chart Front edge of paper
    Void area
    less than 4 mm
    09_ADJUS.fm  5 ページ  2004年12月23日 木曜日 午後2時2分 
    						
    							e-STUDIO162/162D/151/151D ADJUSTMENTS  9 - 6
    B. Adjusting trailing edge void in duplex copy mode
    This is the adjustment of the first surface printing mode (rear end void)
    in duplex copying.
    In a duplex copying operation, the paper is delivered starting from the
    rear end of the first printing surface. It is therefore necessary to make a
    void area at the rear end on the first printing surface to prevent paper
    jam at the fusing part.
    There are two adjustment modes:
    1) Image cut rear end void quantity (R-ADF) 50-19 (SCAN mode
    lamp)
    The size (length) of a document read from the R-ADF is detected,
    the image at the trailing edge of the first printing surface is cut to
    make a void area. (The adjustment of void quantity at the time
    when the cassette paper size is not recognized.)
    2) Paper trailing edge void quantity 50-19 (PRINT mode lamp)
    This adjustment is made when the cassette paper size is
    recognized. The trailing edge void quantity can be adjusted by
    changing the trailing edge image laser OFF timing.
    The paper void quantity should be first adjusted before the image cut
    trailing edge void quantity (R-ADF) is adjusted.
    The adjustment modes can be selected by pressing [
    ←/→] key.
    (Adjustment range; 1 – 99)
    Enter the adjustment value and press [START] key to save the set
    value and make a copy. (The paper information is cleared for every
    copy.)
    When the set value is increased by 1, the void amount is increased by
    about 0.1mm.
    * The initial value of duplex setting is 2to2.
    (Adjustment procedure)
    (1) Paper trailing edge void quantity
    1) Preparing test chart (Draw a scale at the rear end of one side of a
    sheet of A/4 white paper or letter paper)2) Set the test chart on the document glass as shown below.
    3) Execute test command 50-19 to turn on the PRINT mode lamp and
    make the printing mode in OC-D mode.
    Make a copy of the test chart to check the void area of the scale on
    the image.
    Adjust the setting so that the void area is 4 - 5 mm. An increase in 1 of
    setting represents 0.1 mm in void area.
    (2) Image cut trailing edge void quantity (R-ADF)
    1) Set the test chart so that the scale is positioned as shown below.
    2) Execute test command 50-19 to turn on the SCAN mode lamp(on
    the operation panel) and make the printing mode in the D-D mode.
    3) Remove and reinsert the cassette.
    Note: Make sure to carry out this step before making a copy during
    this adjustment.
    4) Make a copy and check the void area of the scale on the image.
    Adjust the setting so that the void area is 2 - 4 mm. An increase of
    1 in setting represents an increase of 0.1 mm in void area.
    l Void position to be checked ModeDisplay 
    itemDefault LED
    Paper rear edge void 
    amountDEN-B 50 PRINT mode lamp
    Print start position (Duplex 
    back surface)RRC-D 50 SCAN mode lamp
    2nd printing surface where scale is printed (lower side)
    Document guideThe trailing edge has a scale
    Table glass
    The trailing edge void on the first printing surface
     is shown above. Paper Void position to be check
    Scale (D-D mode)
    e-STUDIO162_151.book  6 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  ADJUSTMENTS  9 - 7
    5. ADF (RADF) scan position automatic 
    adjustment (With optional ADF/RADF 
    installed)
    Place a black chart so that it covers the ADF scan glass and the OC
    glass together, and close the OC cover.
    When test command 53-08 is executed, the current adjustment value
    is displayed as the initial display.
    * Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about
    0.127mm
    * If the values are kept as the default values, ADF scan is not per-
    formed properly. The front area of the proper scan position may be
    scanned.
    In case of AUTO, press [START] key, and the mirror unit scans from
    the home position to the ADF scan position with the adjustment value
    displayed. The ADF glass cover edge position is calculated from the
    difference between the SPFG glass cover edge and the OC side
    document glass CCD output level. If the adjustment is normal, the
    adjusted value is displayed. If abnormal, the error LED lights up with
    the current set value displayed. 
    During the error LED is lighted, when [START] key is pressed again,
    execution is performed again.
    Operation
    The operation is similar to test command 46-01.  (In MANUAL)
    OK/ERR display in AUTO
    * Use a black chart or prepare a chart as shown below.
    Chart size: 300 x 100, prepared with cutting sheet No. 791 (Black) or
    an equivalent one.
    6. RADF (ADF) mode sub scanning 
    direction magnification ratio adjustment 
    (With optional ADF/RADF installed)
    Note : Before performing this adjustment, be sure to check that the OC
    mode adjustment in copying has been completed.
    1) Put a scale on the original table as shown below, and make a
    normal copy (100%) on the front and the back surfaces to make a
    test chart. 
    Note :Since the printed copy is used as a test chart, put the scale in
    paralled with the edge lines.
    2) Set the test chart  on the RADF and make a duplex copy (D-D or
    D-S) in the normal ratio (100%).
    3) Compare the scale image and the actual image.
    If necessary, perform the following adjustment procedures.
    4) Execute TC 48-05.
    5) The current front surface sub scanning direction magnification ratio
    correction value is displayed in two digits on the display section.
    To select SIDE1 and SIDE2, use [
    ←/→] keys.
    6) Enter the set value and press the start key.
    When adjusting the RADF, use [2-SIDED COPY] key to select
    single/duplex after entering the one page print mode, performing 2-
    page single copy.
    * When there is no document in ADF, copy is inhibited.
    
    ModeDisplay 
    itemDefault LED
    ADF scan position auto 
    adjustment AUTO 1 COPY mode lamp
    ADF scan position manual 
    adjustment MANU 1 PRINT mode lamp
    Reason: To prevent erroneous detection by disturbing light of a
    fluorescent lamp, etc. 
     
    53-08 ADF AUTO
    AUTO  100% **    OK
    53-08 ADF AUTO
    AUTO  100% **    ERR
    6cm or more is required.
    ModeDisplay 
    itemDefault LED
    Sub scan magnification ratio 
    adjustment on the surface of ADF/
    RADF document SIDE1 50 COPY 
    mode lamp
    Sub scan magnification ratio 
    adjustment on the surface of 
    RADF documentSIDE2 50 PRINT 
    mode lamp
    Adjustment 
    modeSpec value TC Set valueSetting 
    range
    Sub scanning 
    direction 
    magnification 
    ratio (ADF/RADF 
    mode)At normal: 
    ±1.0%48-5 Add 1: 
    0.1% increase
    Reduce 1: 0.1% 
    decrease1 – 99
    09_ADJUS.fm  7 ページ  2004年12月22日 水曜日 午後3時39分 
    						
    							e-STUDIO162/162D/151/151D  ADJUSTMENTS  9 - 8
    7. Automatic black level correction
    a. Cases when the adjustment is required
    1) When the main PWB is replaced.
    2) When the EEPROM in the main PWB is replaced.
    3) When U2 trouble occurs.
    4) When repairing or replacing the optical section.
    b. Adjustment procedure
    Used to acquire the black level target value used for the black level
    adjustment of white balance. 
    When test command 63-02 is executed, the current correction value is
    displayed in 3 digits of 12bit hexadecimal number. 
    Place the gray gradation chart used as the correction document so that
    the density 10 (black side) comes on the left side and that the chart is
    upside down at the center of the plate left center.
    When [OK (ENTER)/START] key is pressed, the mirror base unit
    scans the chart and calculates the correction value.
    After completion of correction, the corrected value is displayed on the
    LCD.
    * Default: 0
    * If the value is set to the default, operation is made with 0x60.
    c. Operation
    1) Initial display
    2) [OK (ENTER)/START] Correction start
    
    After canceling, the machine goes into the sub code entry standby
    mode. 
    3) After execution
    3) In case of an error63-02 BLACK LEVEL
                   0
    63-02 BLACK LEVEL
    EXECUTING...
    THE JOB IS BEING
    CANCELED.
    63-02 BLACK LEVEL
                 *** OK 
    63-02 BLACK LEVEL
                 *** ERR
    Chart back surface 
    10
    09_ADJUS.fm  8 ページ  2004年12月22日 水曜日 午後1時45分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 1
    [10] TEST COMMAND, TROUBLE CODES
    1. Entering the test command mode
    To enter the serviceman test command mode, press the keys as follows:
    [#] key 
    → [*] key → [C] key → [*] key
    To cancel the test command mode, press the [CA] key.
    2. Key rule
    3. List of test commands
    [10KEY]: Entry of MAIN CODE/SUB CODE
    Selection of an item
    Setup of an adjustment value in case of test commands for adjustment
    [
    ←/→]: Selection of MAIN CODE/SUB CODE 
    Selection of an item
    [OK (ENTER)/START]: Settlement
    
    [OK (ENTER)]: Settlement (Without print)
    [START]: Settlement/Print
    [C]: (Interrupting operation check) Returns to the upper hierarchy.
    In case of test command of operation check, terminates the operations.
    [CA]: Exits from the test command mode.
    For a test command of adjustment, the display returns to the initial display (00-00).
    Main 
    codeSub 
    codeContents
    1 01 Mirror scan (SCAN CHK)
    02 Mirror home position sensor (MHPS) status display 
    (MHP-SENSOR)
    06 Mirror scan aging (SCAN AGING)
    2 01 Single Paper Feeder (ADF) aging (ADF AGING) 
    (Disabled when set to OC) (Executable only when the 
    ADF is installed.)
    02 ADF sensor status display (ADF SENSOR) (Disabled 
    when set to OC) (Executable only when the ADF is 
    installed.)
    03 ADF motor operation check (ADF MOTOR CHK) 
    (Disabled when set to OC) (Executable only when the 
    ADF is installed.)
    06 RADF resist clutch operation check (RADF RES.CHK)
    (Enabled only when RADF is set.) (Executable only when
    the RADF is installed.)
    08 ADF paper feed solenoid operation check (ADF SPUS 
    CHK) (Disabled when set to OC) (Executable only when 
    the ADF is installed.)
    09 RADF reverse solenoid operation check (RADF SPFS 
    CHK) (Enabled only when RADF is set.) (Executable only 
    when the RADF is installed.)
    10 RADF paper exit gate solenoid operation check (RADF 
    SGS CHK) (Enabled only when RADF is set.) 
    (Executable only when the RADF is installed.)
    3 03 Shifter operation check (SHIFTER CHK)
    5 01 Operation panel display check (LCD/LED CHK)
    02 Fusing lamp, cooling fan operation check (HT LAMP 
    CHK)
    03 Copy lamp ON check (C-LAMP CHK)
    6 01 Paper feed solenoid (CPFS1, CPFS2, MPFS) operation 
    check (PSOL CHK)
    02 Resist roller solenoid (RRS) operation check (RES.R 
    SOL CHK)
    7 01 Check of warm-up display and aging with JAM (W-UP/
    AGING)
    06 Interval aging (INTERVAL AGING)
    08 Shift to copy with warm-up display (W-UP C-MODE)
    Main 
    codeSub 
    codeContents
    8 01 Developing bias output (DVLP BIAS SET.)
    02 Main charger output (Grid HIGH) (MHV(H) SET.)
    03 Main charger output (Grid LOW) (MHV(L) SET.)
    06 Transfer charger output (THV SET.)
    9 01 Duplex motor normal rotation check (DPLX ROT.) 
    (Enabled when Duplex setting is ON) (Executable only 
    when the RADF is installed.)
    02 Duplex motor reverse rotation check (DPLX ROT.REV.) 
    (Enabled when Duplex setting is ON) (Executable only 
    when the RADF is installed.)
    04 Duplex motor rotating speed adjustment (DPLX 
    ROT.SPEED) (Enabled when Duplex setting is ON) 
    (Executable only when the RADF is installed.)
    10 00 Toner motor operation (TONER MOTOR)
    14 00 Cancel of trouble other than U2 (TRBL CANC.)
    16 00 U2 trouble cancel (U2 TRBL CANC.)
    20 01 Maintenance counter clear (M-CNT CLR.)
    21 01 Maintenance cycle setting (M-CYCLE)
    22 01 Maintenance counter display (M-CNT)
    02 Maintenance preset display (M-CNT PRESET)
    04 JAM total counter display (JAM TTL CNT)
    05 Total counter display (TTL CNT)
    06 Developer counter display (DVLP CNT)
    08 ADF counter display (ADF CNT) (Disabled when set to 
    OC) (Executable only when the ADF is installed.)
    11 FAX-related counter display (Executable only when the 
    FAX is installed.)
    12 Drum counter display (DRUM CNT)
    14 ROM version display (ROM VER.)
    16 Duplex counter display (DPLX CNT) (Enabled when 
    Duplex setting is ON) (Executable only when the RADF is 
    installed.)
    17 Copy counter display (COPIES CNT)
    18 Printer counter display (PRT.CNT)
    19 Scanner mode counter display (S-MODE CNT)
    21 Scanner counter display (SCAN CNT)
    22 ADF JAM counter display (S JAM CNT) (Disabled when 
    set to OC) (Executable only when the ADF is installed.)
    10_TESTCOMMAND.fm  1 ページ  2004年12月22日 水曜日 午後1時47分 
    						
    All Toshiba manuals Comments (0)