Home > Toshiba > Copier > Toshiba Estudio 162 Owners Manual

Toshiba Estudio 162 Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Estudio 162 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 22 46 29 Image contrast adjustment 
    (600dpi) (GAMMA 600)[Function]
    Contrast is set for each mode.
    When this test command is executed, the current se value is displayed in 2 digits (Default: 50).
    Change the set value and press [START] key to make a copy under the set value.
    When the set value is increased, the contrast becomes higher. When the set value is decreased, the
    contrast becomes lower.
    In this case, only Exp.3 copy is made. When, however, the setting is made to make higher contrast,
    Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast, Exp1. and
    Exp.5 copies become lower contrast, too.
    Press [
    ←/→] key to switch the mode. The set value of the selected mode is displayed on the LCD.
    (Adjustment value: 1 – 99)
    ∗No density display on LCD.
    [Operation]
    The operation is similar to test command 46-01.
    30 AE limit adjustment (AE 
    LIMIT)[Function]
    Used to set the limit value in AE and AE (toner save).
    Change the setting and press [OK (ENTER)/START] key to write the setting into the EEPROM. The
    machine goes into the sub code entry standby mode.
    By pressing [
    ←/→] key, setting is changed. (Setting range: 0 – 31, Default: 0)
    
    When test command 26-06 (Destination setting) or test command 46-19 Auto Exposure mode is
    changed, the setting of this test command is also changed to the default in connection.
    [Operation]
    The operation is similar to test command 46-19.
    31 Image sharpness 
    adjustment (SHARPNESS)[Function]
    Used to adjust sharpening/blurring of image in each mode.
    When this test command is executed, warm-up and shading are performed and the current set value
    is displayed. (Default: 1)
    Change the set value and press [START] key to make a copy under the set conditions.
    To change the mode, press [
    ←/→] key. The code number of the selected mode is dip0slayed on the
    LCD.
    [Operation]
    The operation is similar to test command 46-01. Main 
    codeSub 
    codeContents Details of function/operation
    Mode Display item Default LED
    AE mode (600dpi) AE 50 COPY mode lamp
    TEXT mode (600dpi) TEXT 50 PRINT mode lamp
    PHOTO mode  PHOTO 50 SCAN mode lamp
    TS mode (TEXT)(600dpi)   TSTXT 50 PRINT  mode  lamp
    SCAN mode lamp
    TS mode (AE)(600dpi)    TSAE 50 COPY mode lamp
    SCAN mode lamp
    Mode Display item Remark
    Limit value for AE AE
    Limit value for AE (toner save) TSAE
    Image quality  Setting  No Remark
    Blurring 0
    Standard 1 Default
    Sharpening 2
    Mode Display item Default setting LED
    AE mode  AE 1 COPY mode lamp
    TEXT mode  TEXT 1 PRINT mode lamp
    PHOTO mode  PHOTO 1 SCAN mode lamp
    TS mode  (TEXT)  TSTXT 1 PRINT  mode  lamp
    SCAN mode lamp
    TS mode  (AE)  TSAE 1 COPY mode lamp
    SCAN mode lamp
    e-STUDIO162_151.book  22 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 23 46 32 Copier color reproduction 
    setting (COLOR 
    REAPPEAR)[Function]
    Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be copied
    can be switched.
    ∗This setting has virtually no effect on black-and-white documents.
    When this test command is executed, warm-up and shading are performed and the current set value
    is displayed. (Default: 0)
    Press [START] key to make a copy under the set conditions . At that time, color components are
    changed for used in copying.
    To change the mode, press [
    ←/→] key. The code number of the selected mode is dip0slayed on the
    LCD.
    [Operation]
    The operation is similar to test command 46-01.
    39 FAX mode sharpness 
    adjustment (Executable only 
    when the FAX is installed.)[Function]
    When [START] key is pressed, scan is started with the entered sharpness adjustment value, and the
    data of the selected mode stored on the FAX side is changed to the entered value.
    [Operation] Main 
    codeSub 
    codeContents Details of function/operation
    Set value Colors easy to be copied Colors difficult to be copied
    0 Purple, Blue, Red Yellow, Green, Water blue
    1 Water blue, Green, Blue Purple, Red, Yellow
    2 Yellow, Red, Green Blue, Water blue, Purple
    Specification component Setting No Remark
    Green 0 Default
    Red 1
    Blue 2
    Mode Display item Default setting LED
    AE mode (including TS) AE 0 COPY mode lamp
    TEXT mode (including TS) TEXT 0 PRINT mode lamp
    PHOTO mode  PHOTO 0 SCAN mode lamp
    Sharpness adjustment value data table
    When initializing each data: 1Mode Sharpness adjustment value
    1: STD
    2: FINE
    3: S-FINE
    4: FINE/PHOTO
    5: S-FINE/PHOTO
    1) Initial display
    2) [
    ←/→] or after 2sec
    Every time when [
    →] key is pressed, the
    second line is changed in the sequence of
    No. 1 
    → 2 → 3 → 4 → 5 → 1.
    When [
    ←] key is pressed, the sequence is
    reversed.
    3) Select the arrow key 1-5, and the LED of
    [START] key is lighted.
    (ZZZZ is the mode selected among STD,
    FINE, S-FINE, FINE/PHOTO, and S-FINE/
    PHOTO.)
    (X is the corresponding sharpness adjustment
    value of the selected mode stored on the FAX
    side.)
    ∗[CLEAR] key: Returns to “2)” display.4) Enter a one-digit value (0-2) as the sharp-
    ness adjustment value with [10KEY].
    (Y is the entered sharpness adjustment value.)
    ∗[CLEAR] key: Returns to “2)” display.
    5) Scan start (self print)
    6) Print start (self print)
    After completion of printing, returns to “4)” 
    display.
    SHARPNESS SETTING
    PRESS ←,→
    SHARPNESS SET (1-5)
    1:STD
    SHARPNESS SETTING
    ZZZZ(0-2)       X
    SHARPNESS SETTING
    ZZZZ(0-2)       Y
    SHARPNESS SETTING
     SCAN           Y
    SHARPNESS SETTING
     PRINT          Y
    e-STUDIO162_151.book  23 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 24 48 01 Main scan/sub scan 
    direction magnification ratio 
    (COPY MAG.)[Function]
    Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direction.
    Enter the adjustment value with [10KEY]. Press [START] key to save the set value and make a copy.
    (When the adjustment value is increased by 1, the magnification ratio is increased by 0.1%.)
    The adjustment mode can be changed by pressing [
    ←/→] key. (Adjustment range: 1 – 99, Default: 50)
    [Operation]
    The operation is similar to test command 46-01.
    05 ADF/RADF mode sub scan 
    direction magnification ratio 
    in copying (ADF/RADF 
    MAG.) (Disabled when set to 
    OC) (Executable only when 
    the ADF/RADF is installed.)[Function]
    Used to display the current ADF/RADF mode sub scan direction magnification ratio on the LCD. 
    When [START] key is pressed, the entered data is acquired and saved into the EEPROM, and a copy
    is made. (When the set value is increased by 1, the magnification ratio is increased by 0.1%.) 
    (Adjustment range: 1 – 99, Default: 50)
    When adjusting the RADF, use [2-SIDED COPY] key to select single/duplex after entering the one
    page print mode, performing 2-page single copy.
    For printing, regardless of the density mode and the density level, 
    Density mode = MANUAL
    Density level = 3
    ∗When there is no document in ADF, copy is inhibited.
    *1: Only when RADF is installed. If installed, skipped.
    [Operation]
    The operation is similar to test command 46-01. Main 
    codeSub 
    codeContents Details of function/operation
    Mode Display item Default value LED
    Main scan direction magnification ratio F-R 50 PRINT mode lamp
    OC mode sub scan direction 
    magnification ratioSCAN 50 SCAN mode lamp
    Mode Display item Default LED
    Sub scan magnification ratio adjustment on the 
    surface of ADF/RADF document SIDE1 50 COPY mode lamp
    Sub scan magnification ratio adjustment on the 
    surface of RADF document *1SIDE2 50 PRINT mode lamp
    e-STUDIO162_151.book  24 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 25 49 01 Download mode 
    (DOWNLOAD MODE)[Function]
    When this test command is executed, DLOWNLOAD MODE is displayed on the LCD and the
    machine goes into the program writing mode from PC to Flash ROM.
    Use the writing tool on the PC and write the program. 
    During writing, the display shows as follows:
    After completion of download, turn OFF/ON the power to reset.
    In case of an error in download, the following message is displayed on the LCD.
    To enter the download mode, there is a method to use key operations as well as to use a test com-
    mand. With the power OFF, press and hold [CA] + [
    ←], turn on the power.
    [Operation] Main 
    codeSub 
    codeContents Details of function/operation
    Status Display item
    Download data receiving RECEIVING
    Loader function transfer  LOADER COPYING
    Date delete start FLASH ERASE
    Data write (Boot section) BOOT WRITING
    Data write (Program section) PROGRAM WRITING
    Data write (EEPROM) E2PROM WRITING
    Data write (LCD) LCD DATE WRITING
    During SUM CHECK FLASH ROM SUM CHECK
    During BOOT SUM CHECK BOOT SUM CHECK
    During EEPROM SUM CHECK EEPROM SUM CHECK
    Download complete DOWNLOAD COMPLETE!
    Error status Display item
    PC data receiving E-01 PC TRANS
    Loader function transfer E-02 LOADER COPY
    FLASH ROM delete E-03 FLASH ERASE
    Boot section FLASH ROM write E-04 BOOT WRITE
    Program section FLASH ROM write E-05 PROGRAM WRITE
    Loader section SUM CHECK E-06 LOADER SUM
    Boot section SUM CHECK E-07 BOOT SUM
    Program section SUM CHECK E-08 PROGRAM SUM
    E2PROM SUM CHECK E-09 E2PROM SUM
    E2PROM write E-10 E2PROM WRITE
    E2PROM read Verify E-11 E2PROM READ
    E2PROM collating Verify E-12 E2PROM COLLATE
    Boot section lens check  E-13 BOOT LENGTH
    Program section lens check  E-14 PROGRAM LENGTH
    E2PROM lens check  E-15 E2PROM LENGTH
    Total data size check  E-16 DATE SIZE
    IMC communication error E-17 IMC TRANS
    IMC FRASH ROM write E-18 IMC FLASH WRITE
    LCD section lens check  E-19 LCD DATE LENGTH
    LCD section FLASH ROM write E-20 LCD DATE WRITE
    LCD section SUM CHECK E-21 LCD DATE SUM
    1) Initial display
    DOWNLOAD MODE
    e-STUDIO162_151.book  25 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 26 50 01 Lead edge image position 
    (LEAD EDGE)[Function]
    Used to adjust the copy image position and the lead edge void amount on copy paper. The adjust-
    ment is made by adjusting the image scan start position at 100% and the print start position (resist
    roller ON timing). When this test command is executed, the current set value is displayed in 2 digits.
    (Center value: 50)
    When [
    ←/→] key is pressed, the setting mode and the display are changed. 
    Enter the adjustment value and press [START] key to save the set value and make a copy. 
    When the adjustment is made by the main cassette paper feed, the adjustment values of all the paper
    feed ports become the same. (When the set value is increased by 1, shift is made by 0.1mm.)
    (*): Support for the installation models. For non-installation models, skip.
    [Adjustment procedure]
    1) Set the print start position (A: COPY mode lamp ON), the lead edge void amount (B: PRINT mode
    lamp ON), the scan start position (C: SCAN mode lamp) to zero, and make a copy of the scale at
    100%.
    2) Measure the image loss (Rmm) of the scale.
    Set C = 10 x R (mm). (Example: Set to 40.)
    When the value of C is increased by 10, the image loss is decreased by 1mm. (Default: 50)
    3) Measure the distance (Hmm) from the paper lead edge to the image print start position. 
    Set A = 10 x H (mm). (Example: Set to 50.)
    When the value of A is increased by 10, the image lead edge is moved to the paper lead edge by
    1mm. (Default: 50).
    4) Set the lead edge void amount to B = 50 (2.5mm). (Default: 50)
    When the value of B is increased by 10, the void is extended by about 0.1mm. (For 25 or less,
    however, the void amount is regarded as 0.)
    ∗The SFP adjustment is made by adjusting the ADF image scan start position after OC adjustment.
    ∗When paper is discharged, the shifter is operated.
    (Example)
    [Operation]
    The operation is similar to test command 46-01. Main 
    codeSub 
    codeContents Details of function/operation
    Mode Display item Default LED
    Print start position (Main cassette 
    paper feed)TRAY1 50 COPY mode lamp
    Main cassette lamp
    (*) Print start position (2nd 
    cassette paper feed)TRAY2 50 COPY mode lamp
    2nd cassette lamp
    Print start position (Manual paper 
    feed)MFT 50 COPY mode lamp
    Manual feed lamp
    Image lead edge void amount DEN-A 50 PRINT mode lamp
    Image scan start position  RRC-A 50 SCAN mode lamp
    Image rear edge void amount DEN-B 50 COPY mode lamp
    PRINT mode lamp
    SCAN mode lamp
    5mm
    10mm
    Distance from the paper lead edge 
    to the image lead edge, H = 5mm
    Image loss, R = 4mm
    e-STUDIO162_151.book  26 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 27 50 06 Copy lead edge position 
    adjustment (ADF/RADF) 
    (ADF/RADF EDGE) 
    (Disabled when set to OC) 
    (Executable only when the 
    ADF/RADF is installed.)[Function]
    Used to adjust the ADF copy lead edge.
    When the adjustment value of the document scan position adjustment is increased by 1, the scan
    start timing is advanced by 0.1mm. 
    The print result is shifted to the opposite direction of the scan start position.
    The adjustment mode can be changed by pressing [
    ←/→] key. (Adjustment range: 1 – 99, Default:50)
    When scanning a back surface of document, the mode must be changed to operate the RADF by
    pressing [2-SIDED COPY] key.
    (*) : Support for the installation models. For non-installation models, skip.
    ∗When there is no document in the ADF, copy is inhibited.
    ∗When paper is discharged, the shifter is operated.
    [Operation]
    The operation is similar to test command 46-01.
    10 Print center offset 
    adjustment (PRT.OFF-
    CENTER)[Function]
    Used to adjust the center offset position of copy images on copy paper and that in scanning docu-
    ment.
    When this test command is executed, the current set value is displayed.
    Enter the adjustment value and press [START] key to save the setting and make a copy. (When the
    set value is changed by 1, the center is shifted by 0.1mm.)
    When the adjustment value is increased, the center is shifted to right. When decreased, the center is
    shifted to left.
    The modes can be selected by pressing [
    ←/→] key.
    When the set value is changed largely, the area outside the shading area may be scanned to cause
    black streaks on the edges. When the RADF is used, select the mode for use of the RADF by [2-
    SIDED COPY] key.
    (*) : Support for the installation models. For non-installation models, skip.
    ∗In the 2nd print center offset adjustment, print is made forcibly as 1to2/Short Edge from OC regard-
    less of duplex setting.
    ∗When paper is discharged, the shifter is operated.
    [Operation]
    The operation is similar to test command 46-01.
    12 Document feed off-center 
    adjustment (ORG.OFF-
    CENTER)[Function]
    Used to adjust document scan off-center adjustment.
    The adjustment modes can be selected by pressing [
    ←/→] key. (Adjustment range: 1 – 99, Default:50)
    When the adjustment value is increased, the print result is shifted to left.
    (*) : Support for the installation models. For non-installation models, skip.
    ∗When paper is discharged, the shifter is operated.
    [Operation]
    The operation is similar to test command 46-01. Main 
    codeSub 
    codeContents Details of function/operation
    Mode Display item Default LED
    Front surface document scan position 
    adjustmentSIDE1 50 COPY mode lamp
    (*) Back surface document scan position 
    adjustmentSIDE2 50 PRINT mode lamp
    Rear edge void adjustment (ADF) END 50 SCAN mode lamp
    Mode Display item Default LED
    Print center offset (Main cassette paper 
    feed)TRAY1 50 COPY mode lamp
    Main cassette lamp
    (*) Print center offset (2nd cassette paper 
    feed)TRAY2 50 COPY mode lamp
    2nd cassette lamp
    Print center offset (Manual paper feed) MFT 50 COPY mode lamp
    Manual feed lamp
    (*) 2nd print center offset (Main cassette 
    paper feed) SIDE2 50 PRINT mode lamp
    Main cassette lamp
    Mode Display item Default LED
    Platen document scan  OC 50 COPY mode lamp
    (*) ADF document front scan ADF 50 PRINT mode lamp
    (*) RADF document back scan  RADF 50 SCAN mode lamp
    e-STUDIO162_151.book  27 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 28 50 18 Memory reverse position 
    adjustment in duplex copy 
    (DPLX REVERSE) (Enabled 
    when Duplex setting is ON 
    with OC or ADF set) 
    (Executable only when the 
    RADF is installed.)[Function]
    When this test command is executed, the current set correction value is displayed.
    Enter the correction value and press [START] key to save the entered correction value. (Correction
    value range; 1 – 99, Default: 50)
    For S-D mode front surface print and print of even paged in D-S mode, reverse memory copy opera-
    tion is performed from the rear edge of documents.
    When, therefore, the print position adjustment of output images is required, adjust as follows:
    In the reverse memory coping, when the document scan is made in the arrow direction, the output
    image is printed from the rear edge of scan image,
    When, therefore, the print lead edge is shifted, set the reference chart so that the reference position is
    on the rear edge, and use this test command to adjust the set value so that the print lead edge is
    matched.
    Since printing is made from the image data most lately stored in memory to the lead edge data from
    the print start position, the image lead edge adjustment is made by changing the end data position
    stored in memory by the set value of this test command.
    Since it is performed by changing the scan end position, the image position adjustment is made by
    changing the scan end position and the end data stored in memory.
    ∗The initial value of duplex setting is 1to2/Long Edge for the duplex model, or 2to1 for the simplex
    model.
    ∗When paper is discharged, the shifter is operated.
    [Operation]
    The operation is similar to test command 46-01.
    19 Duplex copy rear edge void 
    adjustment (DPLX END 
    EDGE) (Enabled when 
    Duplex setting is ON) 
    (Executable only when the 
    RADF is installed.)[Function]
    Used to adjust the rear edge void amount in duplex copy. 
    When this test command is executed, the current set value is displayed in 2 digits. (Center value: 50.)
    The adjustment modes can be selected by pressing [
    ←/→] key. (Adjustment range; 1 – 99)
    Enter the adjustment value and press [START] key to save the set value and make a copy. (The
    paper information is cleared for every copy.)
    When the set value is increased by 1, the void amount is increased by about 0.1mm.
    ∗The initial value for duplex setting is 1to2/Short Edge for the OC/ADF setting, or 2to2 for the
    RADF setting.
    ∗When paper is discharged, the shifter is operated.
    [Operation]
    The operation is similar to test command 46-01. Main 
    codeSub 
    codeContents Details of function/operation
    *1: Only when ADF/RADF is installed. If installed, skipped.Mode Display item Default LED
    OC memory reverse output position  OC 50 COPY mode lamp
    ADF memory reverse output position *1 ADF 50 PRINT mode lamp
    Document transport directionDocument transport direction
    Scan lead edge Print lead edge
    Lead edge void (1)
    Print start position
    Scan end position
    (Default: Scan cut by void (1))   Rear edge void
    Print rear edge
    Scan direction Scan rear edge
    Mode Display item Default LED
    Paper rear edge void amount DEN-B 50 PRINT mode lamp
    Print start position (Duplex back surface) RRC-D 50 SCAN mode lamp
    e-STUDIO162_151.book  28 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 29 51 02 Resist amount adjustment 
    (RESIST ADJ.)[Function]
    Used to adjust the contact pressure of the main unit resist roller and the RADF resist roller onto paper.
    When this test command is executed, the current set value is displayed. 
    The adjustment modes can be selected by pressing [
    ←/→] key.
    Enter the adjustment value with [10KEY] and press [START] key to save the set value and make a
    copy.
    (*): Support for the installation models. For non-installation models, skip.
    [Operation]
    The operation is similar to test command 46-01.
    53 08 ADF scan position automatic 
    adjustment (ADF AUTO) 
    (Disabled when set to OC) 
    (Executable only when the 
    ADF is installed.)[Function]
    Place a black chart so that it covers the ADF scan glass and the OC glass together, and close the OC
    cover.
    When this test command is executed, the current adjustment value is displayed as the initial display.
    ∗Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about 0.127mm
    ∗If the values are kept as the default values, ADF scan is not performed properly. The front area of
    the proper scan position may be scanned.
    In case of AUTO, press [START] key, and the mirror unit scans from the home position to the ADF
    scan position with the adjustment value displayed. The ADF glass cover edge position is calculated
    from the difference between the SPFG glass cover edge and the OC side document glass CCD out-
    put level. If the adjustment is normal, the adjusted value is displayed. If abnormal, the error LED lights
    up with the current set value displayed. 
    During the error LED is lighted, when [START] key is pressed again, execution is performed again.
    [Operation]
    The operation is similar to test command 46-01.  (In MANUAL)
    OK/ERR display in AUTO
    61 03 HSYNC output check (LSU 
    CHK)[Function]
    When [OK (ENTER)/START] key is pressed, HSYNC is performed and the polygon motor is rotated 
    for 30sec. 
    At that time, the COPY mode lamp is lighted for 100msec every time when HSYNC is detected.
    [Operation] Main 
    codeSub 
    codeContents Details of function/operation
    Mode Display item Default LED
    Main cassette paper fed TRAY1 50 COPY mode lamp
    Main cassette lamp
    (*) 2nd cassette paper feed TRAY2 50 COPY mode lamp
    2nd cassette lamp
    Manual paper feed MFT 50 COPY mode lamp
    Manual feed lamp
    (*) RADF document paper feed 
    (Front surface)SIDE1 50 COPY mode lamp
    PRINT mode lamp
    SCAN mode lamp
    (*) RADF document paper feed 
    (Back surface) SIDE2 50 COPY mode lamp
    PRINT mode lamp
    (*) Duplex back surface DUP-2 50 PRINT mode lamp
    SCAN mode lamp
    Mode Display item Default LED
    ADF scan position auto adjustment  AUTO 1 COPY mode lamp
    ADF scan position manual adjustment  MANU 1 PRINT mode lamp
     
    53-08 ADF AUTO
    AUTO  100% **    OK53-08 ADF AUTO
    AUTO  100% **    ERR
    1) Initial display
    61-03 LSU CHK
    EXECUTING...
    e-STUDIO162_151.book  29 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 30 63 01 Shading check (SHADING 
    CHK)[Function]
    Used to display the detection level of white plate for shading.
    When [OK (ENTER)/START] key is pressed, the mirror base unit moves to the white plate for shading
    and the copy lamp is lighted.
    When the light quantity is stabilized, revision is made for every second, and the level of one pixel at
    the center of CCD which is not corrected is detected and the value is displayed in decimal values on
    the LCD. (3 digits)
    [Operation]
    02 Black level automatic 
    correction (BLACK LEVEL)[Function]
    Used to acquire the black level target value used for the black level adjustment of white balance.
    When this test command is executed, the current correction value is displayed in 3 digits of 12bit
    hexadecimal number.
    Place the gray gradation chart used as the correction document so that the density 10 (black side)
    comes on the left side and that the chart is upside down at the center of the plate left center.
    When [OK (ENTER)/START] key is pressed, the mirror base unit scans the chart and calculates the
    correction value.
    After completion of correction, the corrected value is displayed on the LCD.
    ∗Default: 0
    ∗If the value is set to the default, operation is made with 0x60.
    [Operation] Main 
    codeSub 
    codeContents Details of function/operation
    1) Initial display
    63-01 SHADING CHK
    EXECUTING...     000
    Chart back surface 
    10
    1) Initial display
    2) [OK (ENTER)/START] Correction
    start 63-02 BLACK LEVEL
                 000
    63-02 BLACK LEVEL
    EXECUTING...
    After canceling, the machine goes into the sub code entry
    standby mode. 
    3) After execution
    3) In case of an errorTHE JOB IS BEING
    CANCELED.
    63-02 BLACK LEVEL
                 *** OK 
    63-02 BLACK LEVEL
                 *** ERR
    10_TESTCOMMAND.fm  30 ページ  2004年12月22日 水曜日 午後3時40分 
    						
    							e-STUDIO162/162D/151/151D  TEST COMMAND, TROUBLE CODES  10 - 31 64 01 Self print (1by2 mode) 
    (SELF PRT.)[Function]
    The status of the optical section is ignored and printing of one page is made. Also when the print com-
    mand is received from the host, printing is made.
    When this test command is executed, warm-up is performed and the ready lamp is lighted. (Since,
    however, the scanner is disabled, initializing is not made.)
    Enter the code number and press [OK (ENTER)/START] key to start paper feed from the selected
    cassette and print in the selected pattern.
    ∗For 4 – 99, flip.
    [Operation]
    The operation is similar to test command 21-01.
    66 01 FAX soft SW setting 
    (Executable only when the 
    FAX is installed.)[Function]
    Use to check the FAX soft SW setting.
    Every time when the key is pressed, the bit on the first line is switched 0 and 1.
    [Operation]
    02 FAX soft SW initializing 
    (excluding the adjustment 
    values) (Executable only 
    when the FAX is installed.)[Function]
    Use to initializing FAX soft SW.
    [Operation] Main 
    codeSub 
    codeContents Details of function/operation
    Code number Pattern  Display item
    0 1by2 1 BY 2
    1 Grid pattern  CHECK
    2 White paper  WHITE
    3 Black background BLACK
    1) Initial display
    ∗[CLEAR] key: FAX control is terminated.
    2) Enter a 3-digit value of soft SW No. (To
    enter the fourth digit, shift to the left.), and
    the press [OK (ENTER)] key.
    xxxxxxxx is the set content.
    ∗Select 2: Returns to the soft SW No. entry dis-
    play.3) Select 1
    4) Change with 1-8 of [10KEY] and the press
    [OK (ENTER)] key.
    xxxxxxxx is the set content.
    ∗Select 2: Returns to the soft SW No. entry dis-
    play.
    5) Select 1
    After 2sec, returns to 1) Initial display.
    ENTER FAX SOFT SW. #
    (3 DIGITS)    SW.___
    No.###    xxxxxxxx
    CHANGE?   1:YES 2:NONo.###    xxxxxxxx
    USE # KEY   12345678
    No.###    xxxxxxxx
    STORED?   1:YES 2:NO
    STORED
    1) Initial display
    After 2sec, FAX control is terminated.
    INITIALIZED
    e-STUDIO162_151.book  31 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    All Toshiba manuals Comments (0)