Home > Toshiba > Copier > Toshiba Estudio 162 Owners Manual

Toshiba Estudio 162 Owners Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Toshiba Estudio 162 Owners Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							e-STUDIO162/162D/151/151D  MAINTENANCE  11 - 1
    [11] MAINTENANCE
    1. Maintenance table
    : Check (Clean, adjust, or replace when required.) : Clean : Replace : Adjust✩: Lubricate
    2. Maintenance display system
    Section Parts 25K 50K 75K 100K 125K Remark
    Developing Developer
    DV blade
    DV side seal (F/R)
    Process peripheral Drum
    Toner Life8K
    Remaining quantity NEAR EMPTY
    About 10%EMPTY
    LED ON Flash
    Machine Operation allowed Stop
    Developer Life25K
    LED ON at 25K of the developer count.
    Machine Selection is available between Not Stop and Stop by Service Simulation (SIM 26-37) Setup.
    (If Stop is selected, the LED will flash and stop at 25K.)
    ∗ Default: Not Stop
    ∗ Clear: SIM 24-06
    Maintenance LED Selection is available among 25K, 13K, 9K, 6K, 3K, and free (no lighting) with SIM 21-1.∗ Default: 25K
    ∗ Clear: SIM 20-1
    Machine Not stop.
    11_MAINT.fm  1 ページ  2004年12月22日 水曜日 午後2時7分 
    						
    							e-STUDIO162/162D/151/151D  USER PROGRAM  12 - 1
    [12] USER PROGRAM
    The user settings consist of the following items.
    1. User programs
    A. Copy mode
    Program
    numberProgram nameSetting codes
    (factory default setting 
    appears in bold)Explanation
    1 AUTO CLEAR 1: 10 SEC.
    2: 30 SEC.
    3: 60 SEC.
    4: 90 SEC.
    5: 120 SEC.
    6: OFF•Auto clear time automatically returns the copy settings to the initial settings if no 
    keys are pressed for a preset period of time following the end of a copy job.
    •This program is used to select the period of time. Auto clear time can also be 
    disabled.
    2 PREHEAT MODE
    1: 
    30 SEC.
    2: 1 MIN.
    3: 5 MIN.
    4: 30 MIN.
    5: 60 MIN.
    6: 120 MIN.
    7: 240 MIN.•This function automatically switches the machine to a low power consumption 
    state if the set duration of time elapses without the machine being used when the 
    power is on. The power save indicator lights up, however, the keys on the 
    operation panel can be used. Normal operation automatically resumes when a key 
    on the operation panel is pressed, an original is placed, a print job is received.
    3 AUTO SHUT-OFF
    1: ON
    2: OFF•Use this setting to enable or disable auto power shut-off mode.
    4 AUTO SHUT-OFF 
    TIME1: 5 MIN.
    2: 30 MIN.
    3: 60 MIN.
    4: 120 MIN.
    5: 240 MIN.•This function automatically switches the machine to a state that consumes even 
    less power than preheat mode if the set duration of time elapses without the 
    machine being used when the power is on. All lights except the power save 
    indicator  go off. To resume normal operation, press the [START] key. Normal 
    operation also resumes automatically when a print job is received or scanning is 
    begun from a computer. While in auto power shut-off mode, no keys (except the 
    [START] key) can be used.
    5STREAM FEEDING
    1: ON
    2: OFF•When copying using the ADF/RADF, while SET ORIGINALS FOR STREAM 
    FEEDING. appears in the display after an original has been scanned (about 5 
    seconds), a subsequent original can be placed and automatically fed into the 
    machine.
    6LAYOUT IN 2IN1
    1: PATTERN 1
    2: PATTERN 2•Use this setting to select the layout pattern when two original pages are copied 
    onto a single sheet of paper.
    7 OFFSET 
    FUNCTION1: ON
    2: OFF•When enabled, this function offsets the position in the paper output tray of sets of 
    copies during copy job, and print jobs when using the printer function.
    8 ROTATE ORIG. 
    IMAGE1: ON
    2: OFF•When two-sided copying is performed, this function rotates the image on the back 
    of the original. This is convenient when binding the copies at the top (tablet 
    binding).
    9 AE/TEXT 
    RESOLUTION1: 300dpi
    2: 600dpi•This setting is used to change the copy resolution in AUTO and TEXT mode from 
    600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slower when high-
    quality mode is used.
    10 2-SIDED COPY 
    MODE (e-STUDIO
    162D/151D)1: HI-SPEED
    2: NORMAL•If the memory fills up when two-sided copying is performed, NORMAL can be 
    selected to make copying possible. However, NORMAL results in a slower 
    copying speed. Normally HI-SPEED is selected to enable fast two-sided 
    copying.
    11 MARGIN WIDTH 1: 5mm (1/4)
    2: 10mm (1/2)
    3: 15mm (3/4)
    4: 20mm (1)•Use this setting to set the margin width.
    12 MEM. FOR 
    PRINTER1: 30%
    2: 40%
    3: 50%
    4: 60%
    5: 70%•Use this to change the proportion of machine memory used for printer mode.
    13 AUTO KEY REPEAT
    1: ON
    2: OFF•Use this setting to select whether or not holding down a key causes repeated input 
    of the key. For keys that normally cause a set value to increase when held down 
    (for example, holding down the [] key [^]), this program can be used 
    to have the set value not change when the key is held down.
    14 KEY PRESS TIME
    1: NORMAL
    2: 0.5 SEC.
    3: 1.0 SEC.
    4: 1.5 SEC.
    5: 2.0 SEC.•Use this setting to select how long a key must be pressed for the input to be 
    accepted. By selecting a longer time, you can prevent settings from being 
    changed by the accidental pressing of a key.
    e-STUDIO162_151.book  1 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  USER PROGRAM  12 - 2
    B. Print mode
    *1: The scanning speed increases when the USB 2.0 mode is set to HI-SPEED, however, the printing speed does not increase considerably.
    *2: When the 250-sheet paper feed unit is installed.15 KEY TOUCH 
    SOUND1: LOW
    2: HIGH
    3: OFF•This sets the volume of beep signals.
    16 SOUND AT 
    DEFAULT1: ON
    2: OFF•Use this to sound a beep when a base setting is selected.
    17 TONER SAVE 
    MODE1: ON
    2: OFF•This mode reduces toner usage by about 10% when copying. Toner save mode is 
    effective when the exposure mode is AUTO or TEXT.
    18 AE LEVEL ADJUST 1: ADF/RADF
    2: DOCUMENT GLASS•This is used to adjust the exposure level.
    •The automatic exposure level can be adjusted separately for the document glass 
    and the ADF/RADF.
    •The factory default setting for the exposure level is center.
    19 LANGUAGE 1: AMERICAN  ENGLISH
    2: ENGLISH
    3: FRENCH
    4: SPANISH
    :
    :This is used to set the language used in the display.
    20 RESET FACTORY 1: Yes
    2: NoThis is used to return all settings to the factory default settings.
    21 SORT AUTO 
    SELECT1: ON
    2: OFFUse this setting to enable or disable sort auto select mode. Program
    numberProgram nameSetting codes
    (factory default setting 
    appears in bold)Explanation
    Program
    numberProgram nameSetting codes
    (factory default setting 
    appears in bold)Explanation
    1 FORCED OUTPUT 1: ON
    2: OFFWhen this function is enabled, printing in printer mode will automatically continue 
    using a different size of paper if the specified size of paper runs out in all trays. This 
    feature does not function in copy mode.
    2 USB 2.0 MODE 
    SWITCH *
    11: FULL-SPEED
    2: HI-SPEEDThis sets the USB 2.0 data transfer speed. To obtain the fastest speed when using 
    the USB 2.0 connector, first verify that your computer meets the system 
    requirements (operating system and driver), and then use this program to change 
    the USB 2.0 mode to Hi-Speed. Note that the setting should not be changed while 
    running a TWAIN driver. (For the system requirements.)
    3AUTO TRAY 
    SWITCH*
    21: ON
    2: OFFIf the paper runs out during printing and there is paper of the same size in another 
    tray, this function automatically switches to that tray (excluding the bypass tray). The 
    function can be disabled.
    e-STUDIO162_151.book  2 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D  USER PROGRAM  12 - 3
    2. Selecting a setting for a user program
    1) Press the [MENU] key and then press the [OK (ENTER)] key.
    In printer mode, the user programs are accessed by simply press-
    ing the [MENU] key.
    2) Press the [] key [^] to select the item that you wish to
    configure in the USER PROGRAM items, and then press the [OK
    (ENTER)] key.
    •You can also select a program by directly entering the program
    number with the numeric keys.
    3) Press the [
    ] key [^] to change the setting of the
    selected item.
    NOTE:
    •If you mistakenly select the wrong item, press the [CLEAR] key [C]
    and repeat the procedure from step 2).
    •To cancel a setting for a user program, press the [MENU] key.
    4) Press the [OK (ENTER)] key.
    Your selection appears briefly and then the previous screen
    appears.
    NOTE:
    When AE LEVEL ADJUST is selected in the user programs and the
    [OK (ENTER)] key is pressed, the automatic exposure adjustment
    screen appears. Adjust the exposure and press the [OK (ENTER)] key.(e-STUDIO151/151D) (e-STUDIO162/162D)
    (e-STUDIO151/151D) (e-STUDIO162/162D)
    (e-STUDIO151/151D) (e-STUDIO162/162D)
    112222111,2,3,
    1,2,3,SP. FUNCAUTOZOOMOK
    MAIN MENU
    1:USER PROGRAMMAIN MENU
    1:USER PROGRAM
    112222111,2,3,
    1,2,3,SP. FUNCAUTOZOOMOK
    USER PROGRAM
    2:PREHEAT MODEUSER PROGRAM
    2:PREHEAT MODE
    112222111,2,3,
    1,2,3,SP. FUNCAUTOZOOMOK
    PREHEAT MODE
    1:30 SEC.PREHEAT MODE
    1:30 SEC.
    Audible signals (key entry beep, invalid key beep, base setting 
    beep)
    The machine sounds three different types of beep signals: a key
    entry beep that sounds when a valid key is pressed, an invalid key
    beep that sounds when an invalid key is pressed, and a base setting
    beep that sounds when a setting is the same as the base setting
    (base settings are explained below). The base setting beep is initially
    disabled. If you wish to enable the base setting beep, see SOUND
    AT DEFAULT. If you wish to change the volume of the beep signals
    or disable them, see KEY TOUCH SOUND.
    The beep patterns of each type of beep signal are as follows:
    Key entry beep: One beep
    Invalid key beep: Two beepsBase setting beep: Three beeps
    Base settings
    The base settings are preset standard selections for each copy set-
    ting. The base settings are as follows:
    Copy ratio: 100%
    Light and Dark level: centerPaper feed location: 
    Tray 1 (Upper paper tray)
    AUTO/TEXT/PHOTO: AUTO
    e-STUDIO162_151.book  3 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 1
    [13] ELECTRICAL SECTION
    1. Block diagram
    A. Overall block diagram
    Carriage UnitOptional
    CCD PWB
    12V 12V
    RegA5V 
    3.3V
    R
    G8bits (MSB/LSB)
    Optional
    B
    ADF Motor
    5V
    Speaker
    (Power Supply unit)
    Mechanical Load
    FAX only (Optional) MPFS,RRS,CPFS1
    MCU-PWB
    (ADF UNIT SGS, SRRC, SPUS, SPPS,
    4Mb
    or 8Mb  (Counter) MCNT
    256Mbx1 or 16Mb
    3.3V
    D[7..0]
    RD
    IEEE 1284 I/F
    CS
    INTSensor/SW
       (Electorical detector/SW/Sensor)
    UART
    CPU  INTERRUPT
    Printer CLK(16.1511MHz)SPPD
    3.3V
    CPU I/O
    Scanner CLK(48MHz)16.1511MHz
    12MHz
    Interlock SW
    Cassette detector X 2
    Drum Initial detector
    PPD1
    POD
    A[19…1]
        
    OPE PWB
    MFD
    Duplex MotorPPD2
    D[15…0]
    SDOD
    1MbitSPOD
    PSL LEDShifter Motor
    Note: Energy-saving 1W correspondence)
    8Mbit8bit
    Optional
       8bit
    2KbyteFAX OPE PWB
    BuzzerFan Motor (1speed)
    2nd Cassette
    Main Motor
    Toner Motor
    Mirror Motor
    (Optional)
    Polygon
    Mechanical load
    Motor
    CPFS2
    Sensor/SW
    PAPD,PPD3,
    PD2,CED2
    AC Code
    KRONOS  ASIC
    (296pin)
    CPU
    H8S/2321
    (19.6608MHz)
    I
    E
    E
    E
    1
    2
    8
    4
    LSU
    EEPROM
    SDRAM
    16Mbyte
    Reset IC
        SRAM
    Driver
    Flash ROM
    AFE(AD9826)C
    D
    S
    A
    G
    C
    M
    P
    X
    AD
     
    16bits
    CCD Driver
    CCFL x 2Lamp
    Inverter
    HOME
    POSITION
    SENSOR
    CCD
    (uPD8861)
    CPU CLK(19.6608MHz) System ResetSSCG
    PMD
    Driver
    LED Driver
    LED
    Copier 11pcs
    HC151
    KEY Matrix
    Copier 24pcs
    LVC1284
    START KEY
      POWER SUPPLY 
    /POFF,HL,PR
    FW
    3.3V,5VEN,5V,24V
    HVUTC, GRID, MC, BIAS
    PMCLKPSW KEYIN
    SELIN1,2,3 OP-CLK
    OP-LATCH
    OP-DATAPSL MHPS
    Driver
    Driver
    /MMRDY/MMD
    PWM0 - 24V
    HC151
    DC-DC
    Image BUS(PI-Bus)
    Image BUS(PO-Bus)
        OA982
    SDRAM
    Flash ROM
    8
    8
    KEYSCAN1-3
    ISP1581
    USB2.0
    High-speed
    P-Bus
    LCD
    (2 x 20)
    FAX  I/F
    HC238
    (3 to 8 decode)
    LCD E
    LCD RS
    LCD R/W(TBD)
    LCD DB7-4
    FAX
    Modem / LIU PCBA
    Driver
    LCX574
    LASER
    Network BOX
    RJ45
    (N/W
    connec-
    tor)USB
    DC Adapter
    KEY Matrix
    21 pcsLED
    3 pcs
    13_ELECT.fm  1 ページ  2004年12月22日 水曜日 午後2時8分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 2
    2. Circuit descriptions
    A. Main PWB (MCU)
    (1) General
    The MCU PWB is composed of: 
    •CPU peripheral section which performs mechanical sequence
    control, U/I, and each function job management.
    The CPU connects with the ASIC and memory by use of the system
    bus and performs jog management and sequence control of the
    whole engine.
    •Image process ASIC which performs image process, CCD control,
    LSU control, and print control.
    •OA982 peripheral section which performs E-Sort and FAX control.
    The OA982 performs image data input/output with the ASIC,
    SDRAM memory management, and communication with USB2.0
    devices.
    •I/F section for USB2.0 and IEEE1284 control. (For the AL series,
    IEEE1284 is not available.)
    •Motor control circuit
    •Mechanical load, sensor I/O circuit
    It performs control and management of the process, the transport
    loads, the fusing, the optical, and the operation panel sections for exe-
    cuting a series of copy/print/scan operations.
    (2) CPU signal table (H8S/2321)
    PIN 
    No.Signal codeInput/
    OutputOperating
    1 /CS1 Output SRAM chip select
    2 /CS0 Output Flash ROM chip select
    3 GND DGND
    4 GND DGND
    5Vcc CPU3.3V
    6 A0 Output Address bus
    7 A1 Output Address bus
    8 A2 Output Address bus
    9 A3 Output Address bus
    10 GND DGND
    11 A4 Output Address bus
    12 A5 Output Address bus
    13 A6 Output Address bus
    14 A7 Output Address bus
    15 A8 Output Address bus
    16 A9 Output Address bus
    17 A10 Output Address bus
    18 A11 Output Address bus
    19 GND DGND
    20 A12 Output Address bus
    21 A13 Output Address bus
    22 A14 Output Address bus
    23 A15 Output Address bus
    24 A16 Output Address bus
    25 A17 Output Address bus
    26 A18 Output Address bus
    27 A19 Output Address bus
    28 GND DGND
    29 A20 Pull-Up
    30 PSW Interruption 
    level inputPrint SW
    31 SPPD Interruption 
    level inputADF paper sensor
    32 CCD_TG Interruption 
    level inputCCD horizontal sync signal
    33 MHPS Interruption 
    level inputMirror Home Position
    34 /CPUSYNC Interruption 
    level inputHorizontal sync (ASIC)
    35 GND DGND
    36 GND DGND
    37 FW Interruption 
    level inputZero cross signal
    38 ARB_INT Interruption 
    level inputASIC interruption
    39 Vcc CPU3.3V
    40 D0 Data I/O Data bus
    41 D1 Data I/O Data bus
    42 D2 Data I/O Data bus
    43 D3 Data I/O Data bus
    44 GND DGND
    45 D4 Data I/O Data bus
    46 D5 Data I/O Data bus
    47 D6 Data I/O Data bus
    48 D7 Data I/O Data bus
    49 D8 Data I/O Data bus
    50 D9 Data I/O Data bus
    51 D10 Data I/O Data bus
    52 D11 Data I/O Data bus
    53 GND DGND
    54 D12 Data I/O Data bus
    55 D13 Data I/O Data bus
    56 D14 Data I/O Data bus
    57 D15 Data I/O Data bus
    58 Vcc CPU3.3V
    59 POFF Output Shut off control
    60 TxD1 Output For debug
    61 SDA Output EEPROM Data bus
    62 SCL Output EEPROM clock
    63 LCDRS Output LCD control
    64 LCDE Output LCD control
    65 GND DGND
    66 CS4 (FAX) Chip select (FAX)
    67 GND DGND
    68 GND DGND
    69 RY/BY Input Flash Busy signal
    70 LCDDB4 Output LCD control
    71 LCDDB5 Output LCD control
    72 BZR Output Buzzer signal
    73 LCDDB7 Output LCD control
    74 LCDDB6 Output LCD control
    75 Reset OUT1 Output Reset signal
    76 DMT0 Output Duplex Motor signal
    77 DMT1 Output Duplex Motor signal
    78 DMT2 Output Duplex Motor signal
    79 DMT3 Output Duplex Motor signal
    80 WDTOVF Output NC Pull-Up
    81 /RES Input Reset
    82 NMI Output NC Pull-Up
    83 STBY Output NC Pull-Up
    84 Vcc CPU3.3V
    85 XTAL Input Clock
    86 EXTAL Output Clock
    87 GND DGND
    88 CPUCLK Output NC
    89 Vcc CPU3.3V
    90 PRINTST Output Print start signal
    91 /RD Output Read signal
    92 /HWR Output Write signal (High address)
    93 /LWR Output Write signal (Low address)
    94 SELIN3 Output HC151 select signal 
    95 SELIN2 Output HC151 select signal
    96 SELIN1 Output HC151 select signal
    97 ESSTS Output E-sort control
    98 ESCMD Input E-sort control
    99 GND DGND
    100 GND DGND
    101 ESSRDY Input E-sort control
    102 ESCRDY Output E-sort control
    103 AVcc CPU3.3V
    104 Vref CPU3.3V
    105 RTH Analog 
    inputFusing thermistor PIN 
    No.Signal codeInput/
    OutputOperating
    e-STUDIO162_151.book  2 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 3
    (3) Image process ASIC (HG73C114HF)
    a. General
    The ASIC is composed of the three blocks: the image process block,
    the print control block, and the I/F block.
    Image process section
    According to the operation mode set by the register set value, the
    image data from the CCD PWB are placed under shading, AE pro-
    cess, input gamma process, area separation, filter process, resolu-
    tion conversion, zoom process, output gamma process, and binary
    coding. 
    Print control section
    During copying, image-processed data are outputted to the LSU at
    the timing of LSU writing.
    I/F section
    This section performs DRUM control as image data buffer, image
    data send/receive with the OA982, and data send/receive with the
    IEEE1284 I/F. 106 ESPAGE Input E-sort control
    107 SIN1 Input HC151 select detection
    108 SIN2 Input HC151 select detection
    109 SIN3 Input HC151 select detection
    110 Pull up
    111 KEY IN Input NC
    112 MSUST1 Input NC
    113 Avss DGND
    114 GND DGND
    115 /SCANSP Output Scan STOP signal
    116 /SCANST Output Scan START signal
    117 /TRANSST Output ASIC transfer signal
    118 PMCLK Output Polygon clock
    119 SPMT3 Output ADF motor signal
    120 SPMT2 Output ADF motor signal
    121 SPMT1 Output ADF motor signal
    122 SPMT0 Output ADF motor signal
    123 GND DGND
    124 GND DGND
    125 Vcc CPU3.3V
    126 PSL Output Power save LED control
    127 /CS3 Output Chip select signal
    128 /CS2 Output ASIC chip select PIN 
    No.Signal codeInput/
    OutputOperating
    nCS2
    nRDPORT1OUT[15..0]
    nLWRPORT2OUT[10..0]
    A[9..1]
    D[15..0]OPE-LATCH
    LED DriverOPE-DATAto OPU-PWBnRESETControlOPE-CLK
    JTAG TONER MOTORTMCLK,TMENto TONER MOTOR DRIVER
    ControlTM,TM-
    to SDRAM
    64Mb or 128MbCCD-RS,CCD-CK1,CCD-CK2to CCD(SCAN UNIT)
    (Op.400MByte)CCD-CP,CCD-SHRbsmp,vsmp,mclk,OEBafesen,afesck,afesdito AFE(SCAN UNIT)
    to USB I/F
    AFE-DB[7..0]
    to IEEE1284 I/F
    MIRCNT,MTR-Y1,MTR-PH-1,MTR-I01,MTR-I11,MTR-I21
    MTR-Y2,MTR-PH-2,MTR-I02,MTR-I12,MTR-I22
    to MIRROR MOTOR DRIVERSYNC
    to LSU-PWBLDto CCFL(Scan UNIT)LENDCL
    CPUSYNC
    I/O PORT
    CPU BUS
    I/F
    e-STUDIO162_151.book  3 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 4 b. ASIC (Signal table)
    PIN 
    No.Signal Name IN/OUT Connected to Description
    1 cpudata7 IN/OUT CPU CPU data bus
    2 cpudata6 IN/OUT CPU CPU data bus
    3 cpudata5 IN/OUT CPU CPU data bus
    4 cpudata4 IN/OUT CPU CPU data bus
    5 VCC_AC Power
    6 cpudata3 IN/OUT CPU CPU data bus
    7 cpudata2 IN/OUT CPU CPU data bus
    8 cpudata1 IN/OUT CPU CPU data bus
    9 cpudata0 IN/OUT CPU CPU data bus
    10 GND_AC Power
    11 mircnt OUT Buffer IC ADF scanner select 
    signal 
    12 cpusync OUT CPU CPU SYNC signal
    13 mem_intr Not used
    14 arb_intr OUT CPU INTR signal
    15 VCC_core Power
    16 cpu_ad8 IN CPU CPU address bus
    17 cpu_ad7 IN CPU CPU address bus
    18 cpu_ad6 IN CPU CPU address bus
    19 cpu_ad5 IN CPU CPU address bus
    20 GND_core Power
    21 ram_clk_in IN ASIC SDRAM clock on the 
    board
    22 cpu_ad4 IN CPU CPU address bus
    23 cpu_ad3 IN CPU CPU address bus
    24 cpu_ad2 IN CPU CPU address bus
    25 cpu_ad1 IN CPU CPU address bus
    26 cpu_ad0 IN CPU CPU address bus
    27 xcpucs IN CPU CS signal
    28 sfclk IN Oscillator Clock
    29 GND_core Power
    30 xcpuwr IN CPU CPU write signal
    31 xcpurd IN CPU CPU read signal
    32 nrst IN SYSTEM 
    RESETSYSTEM RESET
    33 VCC_core Power
    34 pfclk2 IN Not used
    35 clock_sw IN Pull up
    36 GND_core Power
    37 pfclk1_xout OUT X-tal units VIDEO clock
    38 pfclk1 IN X-tal units VIDEO clock
    39 VSSPLL2 Pull up
    40 VDDPLL2 Pull up
    41 VSS2 Pull up
    42 VDDI2 Pull up
    43 tm2_15m Pull up
    44 xsync IN LSU Horizontal sync 
    signal from LSU 
    (/SYNC)
    45 GND_AC Power
    46 xld OUT LSU Laser drive signal 
    47 xlend OUT LSU Laser APC signal 
    48 VCC_AC Power
    49 mmd OUT Tr array IC Main motor control 
    signal. H: Main 
    motor ON
    50 pmd OUT I/O Polygon motor drive
    51 tc OUT Tr array IC  Transfer charger 
    control signal. H:ON
    52 gridl OUT Tr array IC Main charger grid 
    control signal. H: L 
    output
    53 mc OUT Tr array IC Main charger control 
    signal. H: ON
    54 bias OUT I/O HV bias drive
    55 NC OUT I/O Not used
    56 vfmcnt OUT Tr array IC Ventilation fan 
    rotation speed control 
    signal. H: High 
    speed, L: Low 
    speed
    57 VCC_core Power
    58 vfm OUT Tr  array  IC Ventilation fan control 
    signal. H: Fan ON
    59 /FPOFF OUT I/O FAX poff signal
    60 GND_core Power
    61 DEV DIR OUT I/O CRUM bus control
    62 spfclh OUT Tr array IC ADF/RADF resist 
    roller clutch control 
    signal H:ON
    63 spfrsol OUT Tr array IC ADF/RADF document 
    feed solenoid control 
    signal H:ON
    64 spfgsol OUT Tr array IC ADF/RADF gate 
    solenoid control 
    signal H:ON
    65 spfpsol OUT Tr array IC ADF/RADF document 
    transport solenoid 
    control signal H:ON
    66 VCC_core Power
    67 bias OUT Tr array IC DV bias control 
    signal. H:ON
    68 lden OUT Tr array IC Laser circuit control 
    signal. H: Laser 
    circuit ON
    69 GND_AC Power
    70 MRPS1 OUT I/O ADF current control
    71 MRPS2 OUT I/O ADF current control
    72 MRPS3 OUT I/O ADF current control
    73 CPFS1 OUT I/O 1st cassette pick up 
    solenoid
    74 VCC_AC Power
    75 CPFS2 OUT I/O 2nd cassette pick up 
    solenoid
    76 pr OUT I/O Power relay control
    77 hl OUT Tr array IC Heater lamp control 
    signal. H:ON
    78 GND_core Power
    79 MPFS OUT I/O Multi-bypass solenoid
    80 miron OUT Buffer IC ADF scanner select 
    signal 
    81 spfon OUT Buffer IC ADF ON signal
    82 KEYSC1 OUT I/O Key sense control
    83 KEYSC2 OUT I/O Key sense control
    84 KEYSC3 OUT I/O Key sense control
    85 IMC ready OUT I/O IMC control
    86 VCC_core Power
    87 tmx OUT Buffer IC Toner motor control 
    signal 
    88 tm OUT Buffer IC Toner motor control 
    signal 
    89 op_data OUT Tr array IC Operation circuit data 
    signal
    90 ope_latch OUT Tr array IC Operation circuit latch 
    signal. Data take-in at 
    L
    91 GND_AC Power PIN 
    No.Signal Name IN/OUT Connected to Description
    e-STUDIO162_151.book  4 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 5 92 op_clk OUT Tr array IC Operation circuit 
    clock signal
    93 VCC_AC Power
    94 scanstop IN CPU Scan stop signal
    95 testpin0 IN TEST TEST
    96 testmode_on IN TEST TEST
    97 ie1284_stb IN I/F board 
    connector/STB signal 
    (IEEE1284 
    communication port) 
    98 ie1284_autofd IN I/F board 
    connector/AUTOFD signal 
    (IEEE1284 
    communication port) 
    99 VCC_core Power
    100 ie1284_slctin IN I/F board 
    connector/SLCTIN signal 
    (IEEE1284 
    communication port) 
    101 ie1284_init IN I/F board 
    connector/INIT signal 
    (IEEE1284 
    communication port) 
    102 ie1284_slct OUT I/F board 
    connectorSLCT signal 
    (IEEE1284 
    communication port) 
    103 GND_core Power
    104 ie1284_pe OUT I/F board 
    connectorPE signal (IEEE1284 
    communication port) 
    105 ie1284_busy OUT I/F board 
    connectorBUSY signal 
    (IEEE1284 
    communication port) 
    106 ie1284_ack OUT I/F board 
    connector/ACK signal 
    (IEEE1284 
    communication port) 
    107 ie1284_fault OUT I/F board 
    connector/FAULT signal 
    (IEEE1284 
    communication port) 
    108 VCC_core Power
    109 ie1284_rev OUT I/F board 
    connector/REV signal 
    (IEEE1284 
    communication port) 
    110 ie1284_parad7 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    111 ie1284_parad6 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    112 ie1284_parad5 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    113 ie1284_parad4 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    114 ie1284_parad3 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    115 ie1284_parad2 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    116 VCC_AC Power
    117 ie1284_parad1 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    118 ie1284_parad0 IN/OUT I/F board 
    connectorDATA bus (IEEE1284 
    communication port) 
    119 suspend OUT I/F board 
    connectorSUSPEND signal 
    (USB communication 
    port) 
    120 GND_AC Power
    121 oen OUT I/F board 
    connectorOEN signal (USB 
    communication port) 
    122 vmout OUT I/F board 
    connectorVMOUT signal (USB 
    communication port) 
    123 vpout OUT I/F board 
    connectorVPOUT signal (USB 
    communication port) 
    124 GND_core PowerPIN 
    No.Signal Name IN/OUT Connected to Description
    125 vmin IN I/F board 
    connectorVMIN signal (USB 
    communication port) 
    126 vpin IN I/F board 
    connectorVPIN signal (USB 
    communication port) 
    127 rcv IN I/F board 
    connectorRCV signal (USB 
    communication port) 
    128 scanst IN CPU Scan start signal
    129 printst IN Start signal Start signal
    130 receptst IN Start signal Start signal
    131 transst IN CPU Data transfer start 
    signal
    132 VCC_core Power
    133 dci_dat7 IN E-SORT 
    (OA982)E-SORT data bus
    134 dci_dat6 IN E-SORT 
    (OA982)E-SORT data bus
    135 dci_dat5 IN E-SORT 
    (OA982)E-SORT data bus
    136 dci_dat4 IN E-SORT 
    (OA982)E-SORT data bus
    137 dci_dat3 IN E-SORT 
    (OA982)E-SORT data bus
    138 dci_dat2 IN E-SORT 
    (OA982)E-SORT data bus
    139 dci_dat1 IN E-SORT 
    (OA982)E-SORT data bus
    140 dci_dat0 IN E-SORT 
    (OA982)E-SORT data bus
    141 GND_core Power
    142 out_dc_req IN E-SORT 
    (OA982)E-SORT control 
    signal
    143 in_dc_req IN E-SORT 
    (OA982)E-SORTcontrol signal
    144 GND_AC Power
    145 out_dc_ack OUT E-SORT 
    (OA982)E-SORT control 
    signal
    146 out_dc_wt OUT E-SORT 
    (OA982)E-SORT control 
    signal
    147 VCC_AC Power
    148 in_dc_ack OUT E-SORT 
    (OA982)E-SORTcontrol signal
    149 in_dc_cs OUT E-SORT 
    (OA982)E-SORTcontrol signal
    150 dco_dat7 OUT E-SORT 
    (OA982)E-SORT data bus
    151 dco_dat6 OUT E-SORT 
    (OA982)E-SORT data bus
    152 dco_dat5 OUT E-SORT 
    (OA982)E-SORT data bus
    153 dco_dat4 OUT E-SORT 
    (OA982)E-SORT data bus
    154 dco_dat3 OUT E-SORT 
    (OA982)E-SORT data bus
    155 VCC_AC Power
    156 dco_dat2 OUT E-SORT 
    (OA982)E-SORT data bus
    157 dco_dat1 OUT E-SORT 
    (OA982)E-SORT data bus
    158 dco_dat0 OUT E-SORT 
    (OA982)E-SORT data bus
    159 hsync FAX FAX
    160 GND_core Power
    161 out_req Not used
    162 in_ack Not used
    163 in_cs Not used
    164 GND_AC Power PIN 
    No.Signal Name IN/OUT Connected to Description
    e-STUDIO162_151.book  5 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    							e-STUDIO162/162D/151/151D ELECTRICAL SECTION  13 - 6 165 mdat00 Not used
    166 mdat01 Not used
    167 mdat02 Not used
    168 mdat03 Not used
    169 VCC_core Power
    170 mdat04 Not used
    171 mdat05 Not used
    172 mdat06 Not used
    173 GND_core Power
    174 mdat07 Not used
    175 mdat08 Not used
    176 mdat09 Not used
    177 VCC_AC Power
    178 mdat10 Not used
    179 mdat11 Not used
    180 mdat12 Not used
    181 VCC_core Power
    182 mdat13 Not used
    183 mdat14 Not used
    184 mdat15 Not used
    185 GND_AC Power
    186 pcl_s_print Not used
    187 fax_s_print Not used
    188 es_s_print Not used
    189 out_ack Not used
    190 out_cs Not used
    191 in_req Not used
    192 VCC_core Power
    193 TCK JTAG Not used
    194 TMS JTAG Not used
    195 TRSTA JTAG Not used
    196 TDI JTAG Not used
    197 TDO JTAG Not used
    198 GND_core Power
    199 afp_vsmp OUT CCD PWB AFE control signal
    200 ccd_tg OUT CCD PWB CCD control signal
    201 ccdrs OUT CCD PWB CCD control signal
    202 afp_bsmp OUT CCD PWB AFE control signal
    203 ccdcp OUT CCD PWB CCD control signal
    204 afe_sdata IN CCD PWB ADs serial data
    205 ccd_ph2 OUT CCD PWB CCD control signal
    206 ccd_ph1 OUT CCD PWB CCD control signal
    207 afp_afesen OUT CCD PWB AFE control signal
    208 GND_core Power
    209 afp_adcclk OUT CCD PWB AFE control signal
    210 VCC_core Power
    211 afp_afesck OUT CCD PWB AFE control signal
    212 GND_AC Power
    213 afp_data7 IN CCD PWB Image scan data
    214 afp_data6 IN CCD PWB Image scan data
    215 afp_data5 IN CCD PWB Image scan data
    216 afp_data4 IN CCD PWB Image scan data
    217 afp_data3 IN CCD PWB Image scan data
    218 afp_data2 IN CCD PWB Image scan data
    219 afp_data1 IN CCD PWB Image scan data
    220 afp_data0 IN CCD PWB Image scan data
    221 VCC_AC Power
    222 cl OUT Logic IC Copy lamp control 
    signal
    223 GND_core Power
    224 mtr_y3 OUT I/O Carriage motor 
    current control signal 
    225 mtr_y2 OUT Tr array IC Carriage motor 
    current control signal  PIN 
    No.Signal Name IN/OUT Connected to Description
    226 mtr_y1 OUT Tr array IC Carriage motor 
    current control signal
    227 VCC_core Power
    228 mtr_phase2 OUT Motor driver Carriage motor 
    control signal 
    229 mtr_i02 OUT Motor driver Carriage motor 
    control signal 
    230 mtr_i12 OUT Motor driver Carriage motor 
    control signal 
    231 mtr_i22 OUT Motor driver Carriage motor 
    control signal 
    232 mtr_phase1 OUT Motor driver Carriage motor 
    control signal 
    233 mtr_i01 OUT Motor driver Carriage motor 
    control signal 
    234 mtr_i11 OUT Motor driver Carriage motor 
    control signal 
    235 mtr_i21 OUT Motor driver Carriage motor 
    control signal 
    236 GND_AC Power
    237 ram_mad3 OUT SDRAM SDRAM (Image 
    process page 
    memory) address bus
    238 ram_mad2 OUT SDRAM SDRAM (Image 
    process page 
    memory) address bus
    239 GND_core Power
    240 ram_mad1 OUT SDRAM SDRAM (Image 
    process page 
    memory) address bus
    241 ram_mad0 OUT SDRAM SDRAM (Image 
    process page 
    memory) address bus
    242 ram_mad10 OUT SDRAM SDRAM (Image 
    process page 
    memory) address bus
    243 VCC_core Power
    244 ram_banks1 OUT SDRAM SDRAM (Image 
    process page 
    memory) BANK 
    signal
    245 ram_banks0 OUT SDRAM SDRAM (Image 
    process page 
    memory) BANK 
    signal
    246 xram_cs OUT SDRAM (Image 
    process page 
    memory) CS signal
    247 xram_ras OUT SDRAM SDRAM (Image 
    process page 
    memory) RAS signal
    248 xram_cas OUT SDRAM SDRAM (Image 
    process page 
    memory) CAS signal
    249 VCC_AC Power
    250 xram_wde OUT SDRAM SDRAM (Image 
    process page 
    memory)  WDE signal
    251 ram_dqm0 OUT SDRAM SDRAM (Image 
    process page 
    memory) DQM signal
    252 GND_AC Power
    253 ram_data7 IN/OUT SDRAM SDRAM (Image 
    process page 
    memory) data bus PIN 
    No.Signal Name IN/OUT Connected to Description
    e-STUDIO162_151.book  6 ページ  2004年12月2日 木曜日 午後9時37分 
    						
    All Toshiba manuals Comments (0)