Toshiba Bsx4t Manual

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-32 
 5.4.26  Pre-Strip Selection 
With this parameter you can select whether or not the Pre Strip function is activated.   
When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key 25 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 After selecting the Pre Strip, press the [PAUSE]
 key. 
 
 NOTE:  When the print speed is set to 10”/sec., the pre-strip...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-33 
5.5  PRINTER PARAMETER FINE ADJUSTMENT 
„Outline of Printer Parameter Fine Adjustment 
In the Printer Parameter Fine Adjustment mode, you can fine adjust each parameter, such as Print 
tone, Print start position, Threshold, etc. which are set by the PC command.  This is useful when using 
several types of media by turns or when the print start position or cut/strip position is required to be fine 
adjusted. 
 
The Printer...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-34 
While pressing the [FEED]
 and [PAUSE]
 keys at the same time, turn on the printer.  Hold both keys 
until the “DIAG. Vx.x” Message appears. 
 
 
Press the [FEED]
 key twice.  
The printer is at the start of the Printer Parameter Fine Adjustment menu. 
 
 
 
NOTES: 1.  When pressing the [FEED] and [RESTART] keys at the same time in the parameter 
setting, the message returns to “ADJUST SET”.
 
 
2. If holding the [FEED] or...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-35 
· Feed Length Fine Adjustment (Example) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTE: The fine adjustment value equals to the sum of the fine adjustment values set by the PC 
command and this parameter. 
  The maximum feed length fine adjustment value is ±50.0mm.  When the value reached 
the maximum, the value remains unchanged even if the subsequent fine adjustment is 
performed. 
 
 
 
5.5.2  Cut/Strip Position Fine Adjustment 
With this...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-36 
· Cut Position Fine Adjustment (Example) 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTES: 1. Cut issue is available only when the optional cutter unit (B-7208-QM) is installed.   
 
2.  The fine adjustment value equals to the sum of the fine adjustment values set by the 
PC command and this parameter. 
The maximum cut position fine adjustment value is ±50.0mm.  When the value 
reached the maximum, the value remains unchanged even if the...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-37 
 5.5.3  Back Feed Length Fine Adjustment 
 With this parameter you can fine adjust the Back Feed Length.  When “ADJUST SET” 
appears, press the [PAUSE]
 key and the [FEED]
 key twice. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 [FEED]
 key:  Pressing the [FEED]
 key one time causes a –0.5mm change, up to –9.5 mm. 
 [RESTART] 
key:...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-38 
 5.5.4  X Axis Fine Adjustment 
With this parameter you can fine adjust the print position on X Axis.  When “ADJUST SET” 
appears, press the [PAUSE]
 key and the [FEED]
 key 3 times.  
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 [FEED]
 key:  Pressing the [FEED]
 key one time causes a –0.5mm change, up to –99.5 mm. 
 [RESTART] 
key:...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-39 
 NOTES: 1.  The X Axis fine adjustment is performed to fine adjust the print position in horizontal 
direction (left or right).
 
 
2.  Adjust the X axis within the effective print range.  After the value reaches the 
coordinate 0, the value remains unchanged even if the subsequent fine adjustment is 
performed in the negative direction. 
 3.  This adjustment cannot be used in the Self Test mode or Test print. 
 4.  The fine...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-40 
 5.5.6  Ribbon Motor Voltage Fine Adjustment (Feed/Take-up Motor) 
With this parameter you can fine adjust the Ribbon Motor Voltage (Torque).  When “ADJUST 
SET” appears, press the [PAUSE]
 key and the [FEED]
 key 6 times to enter the Ribbon Motor 
Voltage Fine Adjustment (Take-up Motor) menu. 
 
 
 
To change the screen to the Ribbon Motor Voltage Fine Adjustment (Feed Motor), press the 
[FEED]
 key again.  
 
 
 
When the LCD...

5. SYSTEM MODE  EO18-33012A 
 
5.5 PRINTER PARAMETER FINE ADJUSTMENT 
 
5-41 
 5.5.7  Threshold Manual Fine Adjustment (Black Mark/Feed Gap Sensor) 
 With this parameter you can fine adjust the Threshold of the Black Mark and Feed Gap Sensors.  
When “ADJUST SET” appears, press the [PAUSE]
 key and the [FEED]
 key 8 times to enter 
the Threshold Manual Fine Adjustment (Black Mark Sensor) menu.  
 
 
 
 To change the screen to the Threshold Manual Fine Adjustment (Feed Gap Sensor), press the 
[FEED]
 key...