Toshiba Bsx4t Manual

5. SYSTEM MODE EO18-33012A
 
 
5.10 BASIC SETTING
 
5- 62 
  5.10.2  Basic File Browser 
Data files in the program file and basic file area are displayed.  
When “BASIC” appears, press the 
[PAUSE] key, then 
[RESTART] key. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  5.10.3  Basic Trace Selection Mode 
Select whether the Basic trace specification is enable or not.  
When “BASIC” appears, press the 
[PAUSE] key, then 
[RESTART] key twice. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 7(67%$6
 7(67$7
 7(67%$6
),/(...

5. SYSTEM MODE EO18-33012A
 
 
5.11 DOWN LOAD MODE
 
5- 63 
5.11 DOWNLOAD MODE 
In this mode, the printer enables downloading. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: Centronics Interface ACK/BUSY timing is different between “DOWNLOAD MODE” and 
“DOWNLOAD MODE 2”.).  If data cannot be downloaded in DOWNLOAD MODE, select 
“DOWNLOAD MODE 2” and retry downloading. 
 
2:1/2$ 02( 
5(&(,9,1*
21 /,1(
%6;7 9[[[
Power off. 
2:1/2$ 02(
Select “DOW NLOAD MODE” or 
“DOW...

6. ON LINE MODE EO18-33012A 
 
6. ON LINE MODE 
6- 1 6. ON LINE MODE 
In the ON LINE mode, the following settings can be performed.  
 
Threshold Setting for the Feed Gap Sensor 
Threshold Setting for the Black Mark Sensor 
Reset 
Parameter Settings 
Printer Parameter Fine Adjustment 
Dump Mode 
 
n LED function 
LED Illuminates when… Flashes when… POWER The printer is turned on. ----- ON LINE The printer is ready to print. The printer is communicating with your computer. ERROR Any error occurs with the...

6. ON LINE MODE EO18-33012A 
 
6. ON LINE MODE 
6- 2 n Error messages (continued) 
Error Messages Problems/Cause Solutions PAPER JAM   **** 1. The media is jammed in the media 
path.  The media is not fed smoothly. 
 
 
2. A wrong Media Sensor is selected for 
the media being used. 
 
 
3. The Black Mark Sensor is not 
correctly aligned with the Black Mark 
on the media. 
4. Size of the loaded media is different 
from the programmed size. 
 
 
 
 
 
5. The Feed Gap Sensor cannot 
distinguish the print...

6. ON LINE MODE EO18-33012A 
 
6. ON LINE MODE 
6- 3 n LCD message and LED indication 
Symbols in the message 
1: m: The LED is illuminated.  ¤: The LED is flashing.  l: The LED is unlit. 
2: ****: the number of unprinted media.  Up to 9999 (in pieces) 
3: %%%%%%%: ATA Card’s remaining memory  0 to 9999999 (in K bytes) 
4: ###: Flash memory card remaining memory for PC save area: 0 to 895 (in K bytes) 
5: &&&&: Remaining flash memory capacity for storing writable characters  0 to 3147 (in K bytes) 
 
LED...

6. ON LINE MODE EO18-33012A 
 
6. ON LINE MODE 
6- 4 NOTES: 1. If a command error is found in the command received, 16 bytes of the command error, 
starting from the command code, will be displayed.  (However, [LF] and [NUL] will not be 
displayed.) 
 Example 1 
 [ESC] T20 G30 [LF] [NUL] 
 Command error 
 The following message appears. 
 
 
 
 Example 2 
 [ESC] XR; 0200, 0300, 0450, 1200, 1, [LF] [NUL] 
 Command error 
 The following message appears. 
 
 
 
 Example 3 
 [ESC] PC001; 0A00, 0300, 2, 2, A,...

6. ON LINE MODE EO18-33012A 
 
6. ON LINE MODE 
6- 5 Reset Operation, Parameter Setting, Printer Parameter Fine Adjustment and Dump Mode 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: This section describes the threshold setting for the Feed Gap/Black Mark Sensor, Reset 
Operation, and Dump Mode.  The procedures of the Parameter Setting and Printer Parameter 
Fine Adjustment are described in the System Mode, please refer to Section 5.4 and Section 
5.5, respectively.   Printer Parameter Fine 
Adjustment Dump...

6. ON LINE MODE EO18-33012A 
6.1 THRESHOLD SETTING 
6- 6 6.1 THRESHOLD SETTING 
To maintain a constant print position the printer uses the Transmissive Sensor to detect the gap 
between labels by measuring the amount of light passing through the media.  When the media is pre-
printed, the darker (or more dense) inks can interfere with this process causing paper jam errors.  To 
get around this problem a minimum threshold can be set for the sensor in the following way.  
 
n Threshold setting procedure...

6. ON LINE MODE EO18-33012A 
 
6.2 RESET 
6- 7 6.2 RESET 
Reset operation clears the print data sent to the printer from the computer, and returns the printer to an 
idle condition.  
 
(1) The printer is turned on, standing by, or printing.  
 
 
 
 
(2) To stop printing, or clear the data sent from the computer, press the [PAUSE] key.  The printer 
stops printing.  
 
 
 
 
 
(3) Press and hold the [RESTART] key for 3 seconds or longer.   
 
 
 
(4) Press the [PAUSE] key.  The data sent from the...

6. ON LINE MODE EO18-33012A 
 
6.3 DUMP MODE 
6- 8 6.3 DUMP MODE 
In Dump mode, any characters sent from the host computer will be printed.  Received characters are 
expressed in hexadecimal values.  This allows the user to verify programming commands and debug 
the program.   
 
(1) The printer is turned on, standing by, or printing. 
 
 
 
 
(2) Press the [PAUSE] key. 
 
 
 
 
(3) During the Pause state, press and hold the [RESTART] key for 3 seconds or more. 
The display shows “ RESET”. 
 
 
 
(4)...