Toshiba Bsx4t Manual

5. SYSTEM MODE  EO18-33012A 
 
5.7 SENSOR ADJUSTMENT
 
5-52 
NOTES: 1.  Perform a sensor threshold setting after changing the media to a different type. 
 
2.  An error related to the print position may be caused by the  improperly set sensor 
threshold.  In this case please perform a threshold setting in this mode.  In case further 
adjustment is required, refer to Section 5.5 Printer Parameter Fine Adjustment to make 
the threshold fine adjustment.
 
 
3.  When pressing the [FEED] and [RESTART] keys at...

5. SYSTEM MODE  EO18-33012A 
 
5.7 SENSOR ADJUSTMENT
 
5-53 
 5.7.2  Black Mark Sensor Adjustment 
 
 
 
 
 
 
 Follow the Black mark sensor adjustment procedure below. 
 (1)
 Load a tag stock in the B-SX series printer so that the Black Mark Sensor detects a print 
area (no black mark). 
 (2)
 Press and hold the [RESTART]
 or [FEED]
 key for more than 3 seconds. 
 
 
 
 
 (3)
 Remove the tag stock from the printer.
 
 (4)
 Press the [PAUSE]
 key to show the current Feed Gap Sensor status.
 
 
 
 5.7.3...

5. SYSTEM MODE  EO18-33012A 
 
5.7 SENSOR ADJUSTMENT
 
5-54 
 5.7.4  Black Mark Sensor and Feed Gap Sensor Adjustment (No Paper) 
 
 
 
  
  
 
 
 Follow the Black Mark Sensor (no paper)/Feed Gap Sensor (no paper) adjustment procedure 
below. 
 (1)
 Remove 
any paper from the detecting area of the Black Mark Sensor and the Feed Gap 
Sensor. 
 (2)
 Press and hold the [RESTART]
 or [FEED]
 key for more than 3 seconds. 
 
 
 
 
 
 (3)  Press the [PAUSE]
 key to show the current Ribbon End Sensor status....

5. SYSTEM MODE  EO18-33012A 
 
5.8 RAM CLEAR
 
5-55 
5.8 RAM CLEAR 
„Outline of RAM Clear 
In the RAM Clear mode, clearing the Maintenance Counter and initializing the Parameters are 
possible.  After replacing the print head, ribbon motor, or platen, perform a maintenance clear. 
 
The RAM Clear
 menu contains the following: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
While pressing the [FEED]
 and [PAUSE]
 keys at the same time, turn on the printer.  Hold both keys 
until the “DIAG. Vx.x” Message appears....

5. SYSTEM MODE EO18-33012A
 
 
5.8 RAM CLEAR
 
5-56 
  5.8.2  No RAM Clear 
 
 
 Press the [PAUSE]
 key.  No RAM Clear operation is performed and the display returns to 
“RAM CLEAR”. 
 
  Pressing the [PAUSE]
 key again causes the display to return to “NO RAM CLEAR”. 
 
 
 5.8.3  Maintenance Counter Clear 
 
 
 Press the [PAUSE]
 key to perform the Maintenance Counter Clear. 
 When the Maintenance Counter Clear is completed, the following message appears. 
 
 
 Turn off the printer to exit this mode....

5. SYSTEM MODE EO18-33012A
 
 
5.8 RAM CLEAR
 
5-57 
„Initial values after clearing the parameters (PARAMETER CLEAR) 
Item  Initial Value 
Feed length fine adjustment (PC), (KEY)  0 mm 
Cut (Strip) position fine adjustment (PC), (KEY)  0 mm 
Back feed length fine adjustment (PC), (KEY)  0 mm 
Print tone fine adjustment (Thermal transfer), (PC), (KEY)  0 
Print tone fine adjustment (Thermal direct), (PC), (KEY)  0 
Ribbon take-up motor driving voltage fine adjustment  
(PC), (KEY) 0 
Ribbon feed motor...

5. SYSTEM MODE EO18-33012A
 
 
5.9 IP ADDRESS SETTING
 
5-58 
5.9  IP ADDRESS SETTING 
„Outline of the IP Address Setting
 
In the IP Address Setting mode, you can set the IP Address, Gateway Address, Subnet Mask, DHCP, 
and DHCP ID which are necessary for a network communication.  Since each setting value is different 
depending on your operating environment. 
 
The
 IP Address Setting menu contains the following: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
While pressing the 
[FEED] and 
[PAUSE]...

5. SYSTEM MODE EO18-33012A
 
 
5.9 IP ADDRESS SETTING
 
5-59 
(1) Printer IP Address, Gateway IP Address, and Subnet Mask Settings 
After selecting the menu set the IP address using the following procedure. 
 
 
Set the first 3 digit value with the 
[FEED] or 
[RESTART] key.
 
 
Press the 
[PAUSE] key to move the cursor to the next 3 digit value. 
Set the next values in the same way. 
 
 
 
NOTES: 1. Pressing the [FEED] key one time causes a –1 change.  Pressing the [RESTART] key 
one time causes a +1...

5. SYSTEM MODE EO18-33012A
 
 
5.9 IP ADDRESS SETTING
 
5-60 
(3) DHCP and DHCP ID Settings 
To set the DHCP and the DHCP ID, follow the procedure below.  
 
 
 
 
!,3 $5(66
+&3 21
!,3 $5(66
+&3 &/,(17 ,
02( $6&,,
+&3 &/,(17 ,
02( +(;
+&3 &/,(17 ,
))))))))))))))))
))))))))))))))))
!,3 $5(66
[PAUSE] 
[PAUSE] 
[PAUSE] 
[PAUSE] 
After the 16th byte value is set, the 
display returns to “IP ADDRESS”. 
!,3 $5(66
+&3
!,3 $5(66
+&3 2))
[PAUSE] 
Select ON or OFF with the [FEED] or 
[RESTART] key....

5. SYSTEM MODE EO18-33012A
 
 
5.10 BASIC SETTING
 
5-61 
5.10 BASIC SETTING 
„Outline of Basic Setting 
Setting the BASIC specification and Trace specification to be enabled/disabled, and displaying the 
program file, data file, and area file are available in this mode. 
The Basic Setting menu contains the following.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
While pressing the 
[FEED] and 
[PAUSE] keys at the same time, turn on the printer.  Hold both keys 
until the “DIAG. Vx.x” Message appears.  
 
 
Press the...