Toshiba Bsx4t Manual

6. ON LINE MODE EO18-33012A 
 
6.3 DUMP MODE 
6- 9 (11) Reset the printer by turning the power off and on.  The display shows “ON LINE”. 
 
 
 
 
NOTE: 
When the [PAUSE] key is pressed during printing, the number of unprinted media is displayed. 
The data in the receive buffer is printed as follows: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Print Conditions 
 
· Printing width: 4.2 inches 
· Sensor selection: None 
· Print speed: 6”/sec. (B-SX4T), 5”/sec. (B-SX5T) 
· Printing mode: Depends on...

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.1 OUTLINE OF FEATURES
 
7- 1 
7. PROGRAM DOWN LOAD 
This section provides step-by-step instructions on how to setup and download the firmware to the B-
SX series thermal printer.  The firmware download will be made from a PC via the RS-232C interface 
and Centronics interface of the printer. 
7.1  OUTLINE OF FEATURES 
The software for performing the program download will allow the download of the Firmware (Boot 
program, Application program, and Character generator)...

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.3 FIRMWARE DOWNLOAD
 
7- 2 
 7.2.2 Setup 
 Setup Disk 
 Make sure that you have all two diskettes available of the “Download Program for B-SX”.
 
 
 Installation Procedure
 
 (1)  While running Windows 95 or Windows 98, insert Setup Disk (1/2) into the PC floppy drive. 
 (2)  Click on the START button then highlight RUN and click on RUN.
 
 (3)  When the RUN display appears, type in A:\SETUP and click on OK. 
  (4)  Install the Download Program by following the...

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.3 FIRMWARE DOWNLOAD
 
7- 3 
(1)  Turn on the printer power by the following procedure. 
 
 
 
 
 
 
 
 
 
NOTE:  Program downloading must be performed in the DOWNLOAD MODE.  It cannot be 
performed in On line mode or System mode.  
 
(2)  Turn on the PC power and start up Windows. 
 
(3)  Click on the START button to access the program menu. 
 
(4)  Highlight “TOSHIBA TEC”, ”B-SX” and “Dwnld”, and click on “B-SX Downloader” to start up the 
download program.  The...

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.3 FIRMWARE DOWNLOAD
 
7- 4 
(5)  On the main menu screen, perform Default Device setting and Default Path setting in the 
following procedure. 
  1)  Click on “Setting” on the upper left corner of the main menu screen. 
  2)  Click on “Open” to show the sub menu screen as shown below. 
 
 
 
 
 
 
 
 
 
 
 
 
 
  3)  Click on the Search button to show the sub menu screen as shown below.   
Select a directly to be required as the default path....

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.3 FIRMWARE DOWNLOAD
 
7- 5 
  5)  Select a device to be required as the default device, and then click the OK button.  The 
default device setting is completed.  This setting will be effective next time you start up 
Windows. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTES:  1.  When COM1 or COM2 is selected as the default drive, communications parameter 
will be fixed as follows; Baud rate: 115200bps, Parity: even, Data Length: 8 bits, 
and Stop Bit: 1 bit. 
    2.  The default...

7. PROGRAM  DOWN LOAD EO18-33012A 
 
7.3 FIRMWARE DOWNLOAD
 
7- 6 
(7)  The following message screen appears.  Click on the Yes button to start the program download.  
If canceling the download, click on the No button. 
 
 
 
 
 
 
 
 
NOTE:  While downloading, the following message will appear on the LCD display, respectively. 
  Data in the Flash ROM is being erased.:  “ERASING…” 
  The printer is receiving data.:  “RECEIVING…” 
  Data is being written into the Flash ROM.:  “PROGRAMMING…” 
 
(8)  While...

8. PERIODIC MAINTENANCE PROCEDURE EO18-33012A 
8. PERIODIC MAINTENANCE PROCEDURE 
 
8- 1 8. PERIODIC MAINTENANCE PROCEDURE 
All machines are generally delivered in their best condition.  To maintain optimal operating condition 
and help gain maximum performance and life of machines, we would recommend you to conduct 
periodic maintenance.  Doing this is also effective in preventing unexpected troubles and avoiding 
wasteful system down time, by which more benefit is produced to your customers and greater...

8. PERIODIC MAINTENANCE PROCEDURE EO18-33012A 
8. PERIODIC MAINTENANCE PROCEDURE 
 
8- 2 (5) When using the cutter unit, clean the cutter blade and the media path. WARNING! When cleaning the cutter, be careful not to be injured by the cutter blade.  1) Remove the cutter cover and the media guide cover. 
 B-8204-QM B-4205-QM 
 
 
 
 
 
 
 
 
 
 2) Wipe the cutter blade with a soft cloth or a cotton swab moistened with alcohol. 
  Wipe the media path with a soft cloth moistened with alcohol. 
 B-8204-QM...

8. PERIODIC MAINTENANCE PROCEDURE EO18-33012A 
8. PERIODIC MAINTENANCE PROCEDURE 
 
8- 3 6. Apply FLOIL G-488 to the cutter unit using a soft cloth. 
 
 
 
 
 
All machines are generally delivered in their best condition.  Efforts should be made to keep them 
that way.  Lack of oil, or the presence of debris or dust, may cause an unexpected failure.  To 
maintain in optional operating condition, periodically clean the machine and apply the proper kind 
of oil to each part in which lubrication is needed....