Toshiba Bsx4t Manual

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-22 
 5.4.6  Parity Selection 
 With this parameter you can select the parity of the RS-232C interface.  
 When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key 5 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 After selecting the parity, press the [PAUSE]
 key.  
 
 5.4.7  Transmission Control Code Selection 
With this parameter you can select the...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-23 
  5.4.8  LCD Message Selection 
With this parameter you can select the language in which the LCD message is displayed.   
When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key 7 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 
 
 
 
 After selecting the language, press the [PAUSE]
 key. 
 
  5.4.9  Auto Forward Wait Selection 
With this parameter...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-24 
 NOTES: 1.  If the printer is not used for a few days, the top edge of the media may become curly, 
resulting in a paper jam.  The Auto Forward Wait Function prevents this problem since 
the media feed amount is increased so that the media stops past the platen.
 
  
2.  When the Stop Position Fine Adjustment Value is set to + direction, the media will stop 
past the media outlet. 
When the value is set to – direction, the media will stop...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-25 
 5.4.12 Control Code Selection 
With this parameter you can select a Control Code.  When “PARAMETER SET” appears, 
press the [PAUSE]
 key and the [FEED]
 key 11 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 
 
NOTES: 1.  This parameter is used to select the Control Code for the communication between  
    
the printer and the host computer. 
  
2.  Selecting...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-26 
After setting the control code for Control Code 1, press the [PAUSE]
 key to show the CONTROL 
CODE2 screen.  In a same manner, press the [PAUSE]
 key after setting the control code for 
Control Code 2 to display the CONTROL CODE3 screen. 
 
 
 
 
 
 
 
Press the [PAUSE]
 key after setting the control code for Control Code 3, and the Strip Wait 
Status Selection screen will appear. 
 
 
  5.4.13 Strip Wait Status Selection 
With this parameter...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-27 
= 
 5.4.15  KANJI Code Selection 
With this parameter you can select KANJI code.  When “PARAMETER SET” appears, press 
the [PAUSE]
 key and the [FEED]
 key 14 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
NOTE: Kanji code selection is not supported by the QQ/QP models as the Kanji ROMs are not 
installed. 
 
 After selecting the Kanji code, press the [PAUSE]
 key....

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-28 
 5.4.17  Auto Print Head Check Selection 
With this parameter you can select whether or not the Auto Print Head Check function is 
activated at the power on time.  When “PARAMETER SET” appears, press the [PAUSE]
 key 
and the [FEED]
 key 16 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 NOTES: 1.  It will take about 2 seconds to perform the Auto Print Head check....

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-29 
 NOTE: ACK/BUSY Signal Timing Chart 
   If the error occurs with the Centronics interface communication, change the types. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 5.4.19  Web Printer Function Selection 
With this parameter you can select whether or not the B-SX series printer can be used as a web 
printer.  When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key 18 
times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-30 
 5.4.20  Input Prime Selection 
With this parameter you can select whether or not the Reset operation can be performed when 
INIT signal is ON.  When “PARAMETER SET” appears, press the [PAUSE]
 key and the 
[FEED]
 key 19 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 After selecting the Input Prime, press the [PAUSE]
 key. 
 
  5.4.21  Ribbon Near End Selection 
With...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-31 
 5.4.23  Centronics Interface Selection 
With this parameter you can select Type of the Centronics interface operating mode. 
When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key 22 times. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 After selecting the Centronics Interface, press the [PAUSE]
 key. 
 
 
 5.4.24  Plug & Play Selection 
With this parameter...