Toshiba Bsx4t Manual

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 4 4.1 SWING CUTTER (B-4205-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. This optional device is used for cut print, which cannot be used together with either B-8204-QM or B-
9904-H-QM. 
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Cutter Unit (1 pc.) Cutter Cover (1 pc.) Cutter Harness (1 pc.) Print Head Cleaner (1...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 5 2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Open the printer block. (Refer to Section 3.3.) 
5) Attach the cutter unit to the front of the printer with the cutter attachment screws and the FL-4x6 
screw. 
 
 
 
 
 
 
 
 
 
 
 
6) Connect the cutter harness to CN1 on the cutter I/F PC board. 
7) Fit the bush to the cutter...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 6   9) Close the print head block and the ribbon shaft holder plate.  
NOTE: DO NOT excessively push down the print head block to close it.  Doing so may cause a 
failure of the print head block or damage to the print head. 
10) Connect the cutter harness to CN15 on the Main PC Board.  
 
 
 
 
 
 
 
 
 
 
 
11) Fit the cutter cover on the cutter attachment screws, and fix it to the cutter unit with the two...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 7 4.2 ROTARY CUTTER (B-8204-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. This optional device is used for cut print, which cannot be used together with either B-4205-QM or B-
4905-H-QM. 
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Cutter Unit (1 pc.) 
 
 
 
 
 
 Cutter Cover (1 pc.) Cutter Drive Unit (1 pc.) Harness...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 8 1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 
2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Fix the cutter drive unit to the printer with the three SM-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
5) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter 
driver...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 9 7) Insert the harness ass’y into the hole in the main frame.  Fit the bush into the hole. 
 
 
 
 
 
 
 
 
 
 
 
8) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the 
Main PC board, respectively.  
 
 
 
 
 
 
 
 
 
 
 
 
9) Open the printer block. (Refer to section 3.3.) 
10) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4-10 11) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three 
SM-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
12) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover 
turns on the cutter cover open switch. 
 NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover. 
  2. Make sure that the...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-11 4.3 STRIP MODULE (B-9904-H-QM) 
This optional device is used for strip print, which cannot be used together with either B-4205-QM or B-
8204-H-QM. 
 
NOTE: The strip module is standard on the B-SX5T series.  
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Rewinder Ass’y (1 pc.) 
 
 
 
 
 
 Rewinder Guide Plate (1 pc.) Bush (1 pc.) 
 Strip Sensor (TR) (1...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-12   1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 
2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Remove the operation panel ass’y from the printer. (Refer to section 3.4.) 
5) Attach the rewind paper guide to the base with the two M-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
6) Align the notch of the...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-13  8) Fit the bush to the longer harness of the rewind full sensor (Tr) and the rewinder harness in the 
orientation shown below.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9) Insert the longer harness of the rewind full sensor (Tr) into the hole in the printer frame.  Fit the 
bush into the hole.  
    SM-4x8B Screw SM-4x8C ScrewSM-4x8B Screw Take-up Holder Notch Rewind Full Sensor (LED)...