Toshiba Bsx4t Manual

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-24   5) If the PCMCIA interface board is used together with the USB interface board, attach the PCB 
attachment plate to the plate to which the PCMCIA interface board is secured with the SM-3x6 
screw.  If not, go to the next step.  
 
 
 
 
 
 
 
 
 
 
 
 
6) Firmly connect CN50 connector on the USB interface board directly to CN7 on the Main PC board 
or CN1 on the PCMCIA interface board....

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-25   7) Secure the USB interface board to the rear plate with the two SM-3x6 screws.  
 
 
 
 
 
 
 
 
 
 
 
 
 
8) Tighten the two M-3x5 screws of the USB interface board that were loosened previously. 
(Refer to Caution) 
9) Secure the USB interface board to the PCB support plate (when connecting to the Main PC board) 
or PCB attachment plate (when connecting to the PCMCIA interface board) with...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-26  10) Attach the blind plate A to the rear plate.  If the PCMCIA interface board has been installed,  
 go to the next step.  
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: In case that the PCMCIA interface board has been installed, retain the blind plate A.  
 
11) Reassemble the side panel (L) to the printer in the reverse order of removal.  
 
 
 Blind Plate A  SM-3x6 Screw Rear Plate 

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-27 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
This optional interface board enables the printer to be used in a LAN network. 
CAUTION! 
1. Loosen the two M-3x5 screws of the LAN interface board before installing it.  Failure to do this 
may cause damage to the connector.  
 
 
 
 
 
 
 
 
 
2. When using the PCMCIA interface board together, first install the PCMCIA PC board, and then 
LAN interface...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-28 1) Loosen the two M-3x5 screws of the LAN interface board. (Refer to Caution above.) 
2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
3) Remove the two SM-3x6 screws to remove the blind plate A from the back. 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: Keep the blind plate A safe as this will be necessary when the machine is modified to the 
standard type. 
 
4) If the PCMCIA...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-29 5) Firmly connect CN50 on the LAN interface board directly to CN7 on the Main PC board or CN1 on 
the PCMCIA interface board.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6) Secure the LAN interface board to the rear plate with the two SM-3x6 screws. 
 
 When connecting to the Main PC Board When connecting to the PCMCIA Interface Board  LAN Interface Board MAIN PC BoardCN50 CN7   LAN...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-30  7) Tighten the two M-3x5 screws on the LAN interface board that were loosened previously. 
(Refer to Caution.) 
8) Secure the LAN interface board to the PCB support plate (when connecting to the Main PC board) 
or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 
screw. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9) Reassemble the side panel (L) in...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
 
4-31 4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
This optional interface board is provided with an expansion I/O interface. 
NOTE: The expansion I/O interface board is standard on the B-SX5T series.  
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Expansion I/O Board (1 pc.) Expansion I/O Cable (1 pc.) 
  Installation Manual (1 copy)...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
 
4-32 5) Connect the expansion I/O cable to CN3 on the Main PC board.  
 
 
 
 
 
 
 
 
 
 
6) Secure the expansion I/O board to the rear plate with the two B-3x6 screws removed in Step 4. 
7) Connect the expansion I/O cable to CN1 on the expansion I/O board.  
 
 
 
 
 
 
 
 
 
 
 
8) Reassemble the side panel (L) in the reverse order of removal.  
9) Perform a loop back check to confirm...

5. SYSTEM MODE  EO18-33012A 
 
5.1 OPERATION PANEL
 
5-1 
5. SYSTEM MODE 
This chapter describes usage and purpose of the keys on the Operation Panel in System Mode. 
For service personnel, System Mode should be used for the following eight purposes: 
· To check and print the system status, the Maintenance Counter, and the Print Head Element. 
· To set the parameters for the communication with the host computer, and the printer functions 
such as the keys and LCD Message Display. 
· To make fine...