Toshiba Bsx4t Manual

PRINTED IN JAPAN
EO10-33013A 

 
PRINTED IN JAPAN 
 
TEC Thermal Printer 
B-SX4T/SX5T SERIES 
 
Document No. EO18-33012A 
 
Original Jan., 2003 
(Revised Feb., 2003) 
 
Maintenance Manual  

 
 
 
NOTES:  1.  Manual instructions must be followed when installing option kits or adding cables 
to avoid system failures and to insure proper performance and operation. 
2.  Failure to follow manual instructions or any unauthorized modification, 
substitution or change to this product will void the limited product warranty. 
WARNING! 
Follow all manual instructions.  Failure to do so could create safety hazards such as fire or 
electrocution.  

EO18-33012A 
 
TABLE OF CONTENTS 
 
 Page 
1. UNPACKING --------------------------------------------------------------------------------------------- 1- 1 
 1.1 PROCEDURES ----------------------------------------------------------------------------------------- 1- 1 
 1.2 CHECKS -------------------------------------------------------------------------------------------------- 1- 3 
2.  PRINTER INSTALLATION --------------------------------------------------------------------------- 1- 3 
3.  NOTE FOR...

EO18-33012A 
 
      5.4.11  Ribbon Saving Function Selection ------------------------------------------------------- 5-24 
      5.4.12  Control Code Selection --------------------------------------------------------------------- 5-25 
      5.4.13  Strip Wait Status Selection ----------------------------------------------------------------- 5-26 
      5.4.14  FEED Key Function Selection ------------------------------------------------------------- 5-26 
      5.4.15  KANJI Code...

EO18-33012A 
 
      5.8.3  Maintenance Counter Clear---------------------------------------------------------------- 5-56 
      5.8.4  Printer Parameter Clear--------------------------------------------------------------------- 5-56 
  5.9  IP ADDRESS SETTING ------------------------------------------------------------------------------ 5-58 
 5.10 BASIC SETTING --------------------------------------------------------------------------------------- 5-61 
      5.10.1  Basic Specification Selection Mode...

EO18-33012A 
 
      10.11.4  Reassembling the Media Sensor Ass’y ----------------------------------------------- 10-30 
  10.12  HEAD UP SENSOR --------------------------------------------------------------------------------- 10-32 
 10.13 PRINTER OPEN SENSOR ------------------------------------------------------------------------ 10-34 
  10.14  RIBBON END SENSOR---------------------------------------------------------------------------- 10-36 
 10.15 FAN...

1. UNPACKING EO18-33012A 
1.1 PROCEDURE 
 
1- 1 1. UNPACKING 
1.1 PROCEDURE 
1) Open the carton. 
2) Unpack the accessories and the front pad from the carton. 
 
 
 
 
 
 
 
 
 
 
 
 
3) Unpack the pads and the printer from the carton. 
 
 
 
 
 
 
 
 
 
 
 
 
4) Remove the four pieces of tape and the rear pad from the printer. 
 
 
 Carton Accessories 
Front Pad  Printer 
Bottom Pad Right Side Pad Left Side Pad  Tape 
Rear Pad Tape    

1. UNPACKING EO18-33012A 
1.2 CHECKS 
 
1- 2 5) Open the top cover and remove the five pieces of tape.  And then, open the ribbon shaft holder 
plate to remove the ribbon shaft pad from the printer. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6) In case of the B-SX5T series, take out the rewinder guide plate and two SMW-3x8 screws from 
the printer inside.  Also, remove the tape from the rewinder unit in the printer.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: For the installation procedure of the...