Toshiba Bsx4t Manual

5. SYSTEM MODE  EO18-33012A 
 
5.2 OVERVIEW
 
5-2 
5.2 OVERVIEW 
System Mode consists of nine main menus: Self-Diagnostic Test, Parameter Setting, Printer Parameter 
Fine Adjustment, Test Print, Sensor Adjustment, RAM Clear, IP Address Setting, Basic Setting, and 
Factory Mode. 
 
While pressing the [FEED]
 and [PAUSE]
 keys at the same time, turn on the printer.  Hold both keys 
until “DIAG. Vx.x” message appears on the display....

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5-3 
5.3  SELF-DIAGNOSTIC TEST 
„Outline of Self-Diagnostic Test 
In the Self-Diagnostic Test mode ,the printer checks and prints out  the printer system information such 
as the sensor or interface, and the Maintenance Counter.  Also it makes the print head broken element 
check. 
 
The Self-Diagnostic Test contains the following sub menus: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: Use the [FEED] or [RESTART] key to select a...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5-4 
 5.3.1
 Printing Mode Selection 
 Press the [PAUSE]
 key.  The type of printing mode can be selected: 
 “TRANSFR” (Thermal transfer) or “DIRECT” (Thermal direct). 
 After selecting the printing mode to be used, press the [PAUSE]
 key. 
 
 
 
 
 
 
 
 
 
NOTE: When using the ribbon, be sure to select “Thermal Transfer”.  When using the thermal 
media, be sure to select the “Thermal Direct”.
 
 
 5.3.2
 Dispensing Mode Selection 
  When...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 5 
 5.3.3  Maintenance Counter/Parameter Settings Print Out 
The printer is ready to print out the Maintenance Counter/Parameter Settings.  Press the 
[PAUSE]
 key to start. 
 
 
 
 The printer starts printing out the Maintenance Counter/Parameter Settings.  During printing, the 
message below appears on the display. 
 
 
 
 After printing is completed, the display returns to “DIAG.  Vx.x”. 
 
· Print Sample...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 6 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTE: Print conditions: 
  
Preset count: 1, Print speed: 6”/sec. (B-SX4T) or 5”/sec. (B-SX5T), Sensor: No sensor, 
Printing mode: Thermal transfer, Media length: 288 mm, Issue mode: Batch printing
 
 
· Descriptions of the Maintenance Counter 
# Item  Count Condition  Range 
(1) 
 
(2) Total media distance 
covered 
Media distance covered Counted when the feed motor drives to feed, 
print...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 7 
 NOTES: 1.  Item from (2) through (10) are initialized to “0” after RAM clear. 
  
2.  If the print distance is 8.2m or less (B-SX4T) or 5.5m or less (B-SX5T), it is rounded 
down and no data is added to the memory at power off.
 
  
3.  If the count is 31 or less, it is rounded down and no data is added to the memory at 
power off.
 
  
4.  If the driving time is 32 sec. or less (B-SX4T) or 27sec. or less (B-SX5T), it is rounded 
down and...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 8 
# Item  Contents 
(27)  Language selection for LCD message  ENGLISH: English 
GERMAN: German 
FRENCH: French 
DUTCH: Dutch 
SPANISH: Spanish 
JAPANESE: Japanese 
ITALIAN: Italian 
(28)  Auto forward wait  ON: Available 
OFF: Unavailable 
NOTE:  The stop position fine 
adjustment value is also 
printed out. 
Head up on in cut mode  ON: Available 
OFF: Unavailable (29) 
Rewinder selection  ON: Rewinder is used. 
OFF: Rewinder is not used....

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 9 
 
# Item  Contents 
(42)  Centronics interface operating mode  SPP: Compatible mode 
ECP: ECP mode 
(43)  Plug & Play setting ON: Available 
OFF: Unavailable 
(44)  Print processing setting at the label end detection TYPE1: Printing is paused while the 
label is issued. 
TYPE2: Printing is paused after the 
label is issued. 
(45)  Pre-Strip setting ON: Available 
OFF: Unavailable 
(46)  Back Feed Speed setting  STD: 3”/second 
LOW :...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 10 
  5.3.4  Self-Diagnostic Test and Result Print Out 
When the Maintenance Counter/Parameter Settings is printed, the message returns to 
“DIAG. Vx.x”.  Press the [PAUSE]
 key twice. 
 
 The Self-Diagnostic Test is ready.  Press the [PAUSE]
 key to start. 
 
 
 
 The printer starts printing out the Self-Diagnostic Test, and prints out the result.  During printing, 
the message below appears on the display. 
 
 
 
 After printing is completed,...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 11 
· Descriptions 
 (1)  Program ROM Check (Model Name, Date, Version, Part number, Checksum) 
 PROGRAM
  B-SX4T 7FM00226000 
    
 
 
 
 
 MAIN
 01DEC2002 V1.0 A : 1A00 
 
 
 
 BOOT
 16DEC2002 V1.0 A : 8500 
 
 
 (2)  Alphanumeric Font ROM Check 
 FONT
 5600 
 
 
 
 (3)  Kanji ROM Check 
  KANJI
 NONE 
 :  0000 
 
 
 
 
 NONE
  :  0000 
 
 
 
 (4) EEPROM Check 
  EEPROM
 OK 
 
 
 
 
 (5) SDRAM Capacity 
  SDRAM
 8MB 
 
 
 
OK: Data in the...