Toshiba Bsx4t Manual

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 12 
 (6)  PC Card Slot Check 
 CARD
 SLOT 1 ATA 
    SLOT 2
 LAN 
 
 
 
 
 
 
 
 
 (7)
 Sensor 1 Check 
  The status of the Strip Sensor, Ribbon Feed Motor Sensor, Ribbon Take-up Motor Sensor, 
Rewinder Overflow Sensor, Cutter Home Position Sensor, Print Head Up Sensor, and Print 
Block Open Sensor are printed. 
 
  SENSOR1     00000000
, 0 1 1 1 0 0 1 1 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
ATA:  ATA Card is inserted. 
LAN:  LAN card is...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 13 
 
Sensor/Switch  Print status content description 
Printer block open sensor  Detects the Open or Close status of the printer block.  W hen 
the printer block is closed, printing is performed. 
Print head up sensor  Detects the Up or Down status of the print head.  W hen the 
print head is down, printing is performed. 
Cutter home position sensor  Indicates whether or not the cutter is at the home position. 
Rewinder overflow sensor...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 14 
 (9)
 Expansion I/O Interface Check 
 EXP.I/O
 OK 
 
 
 
 
 
Connect the jig like below to the Expansion I/O PC board’s connector and perform a loop 
back check.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 (10)
 Internal Serial Interface Check 
 EX.232C
 NG 
 
 
 
 
Connect the jig like below to the serial interface connector and perform a loop back check.  
 
Loopback test 
OK: The circuit has no problem. 
NG: The circuit has a problem or...

5. SYSTEM MODE  EO18-33012A 
 
5.3 SELF-DIAGNOSTIC TEST
 
5- 15 
  5.3.5  Print Head Element Check 
When the Self-Diagnostic Test result is printed, the message returns to “DIAG. Vx.x”.  Press 
the [PAUSE]
 key three times and [FEED]
 key twice. 
 
The printer is ready to check the print head to see if there is any problem with the print head.  
Press the [PAUSE]
 key to start. 
 
 
 
 The printer starts checking the print head. 
 
 
 
If there is no problem with the print head, the print head check is...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-16 
5.4 PARAMETER SETTING 
„Outline of Parameter Setting 
In the Parameter Setting mode, various kinds of parameters, such as communication, key, LCD, etc. can be set.  
This will allow the use of the printer to comply with your operating conditions. 
The 
Parameter Setting menu contains the following: 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Character code selection 
Zero font code selection 
Baud rate...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-17 
NOTE: Baud rate, Data length, Parity, and Transmission control code should be set to the same 
values as those of the host computer.  Failure to do this causes improper operation. 
 
While pressing the [FEED]
 and the [PAUSE]
 keys at the same time, turn on the printer.  Hold both 
keys until the “DIAG. Vx.x” message appears. 
 
Press the [FEED] 
key.  The printer is at the start of the Parameter Setting menu. 
 
 
 
 5.4.1  Character Code...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-18 
Example:  Character code table 
Printable characters depend on the fonts.  The fonts of the following characters are Times 
New Roman, Helvetica, Letter Gothic, Prestige Elite, Courier, and Gothic 725 Black 
 
 
PC-850 PC-8 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PC-852 PC-857 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
B-851 B-855 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
  

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-19 
 
PC-1250 PC-1251 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PC-1252 PC-1253 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
PC-1254 PC-1257 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-20 
LATIN9 Arabic 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 NOTE: Euro font codes are changeable.  For details, refer to Euro Code Selection of Section 5.4 
Parameter Setting.
 
 
 5.4.2  Zero Font Code Selection 
 With this parameter you can select the way to indicate zero between “0” and “
Ø”. 
 When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a...

5. SYSTEM MODE  EO18-33012A 
 
5.4 PARAMETER SETTING
 
5-21 
 5.4.3  Baud Rate Selection 
With this parameter you can select the baud rate of the RS-232C interface.   
When “PARAMETER SET” appears, press the [PAUSE]
 key and the [FEED]
 key twice. 
 
 
 
 Press the [PAUSE]
 key to start.  Use the [FEED]
 or [RESTART]
 key to select a desired option.
 
 
 
 
 
 
 
 
 
 
 
 After selecting the baud rate, press the [PAUSE]
 key. 
 
 5.4.4  Data Length Selection 
With this parameter you can select the...