Toshiba Bsx4t Manual

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-14   10) Connect the longer harness of the rewind full sensor (Tr) and the rewinder harness to CN4 and 
CN15 on the Main PC board, respectively.  
 
 
 
 
 
 
 
 
 
 
 
NOTES:  
1. You should change the selection switch setting depending on the issue mode.  Improper setting 
may affect the print quality. 
 STANDARD/PEEL OFF (STRIP): Batch or strip mode 
 REWINDER: Built-in rewinder mode 
 For the cut mode,...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-15    13) Secure the strip sensor (LED) and strip sensor (Tr) to the printer with the SM-4x8B screws.  
14) Connect the shorter harness of the strip sensor (Tr) to the strip sensor harness (for LED). 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
15) Fix the connected strip sensor harness (for LED) to the base with the cable clamp.  While passing 
the other strip sensor harness through the cut and the bush,...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-16   16) Fix the strip sensor harness with the three cable clamps and connect it to CN20 on the Main PC 
board.  
 
 
 
 
 
 
 
 
 
 
 
 
 
17) Reassemble the side panel (L) in the reverse order of removal.  
18) Close the print head block and ribbon shaft holder plate.  
NOTE: DO NOT excessively push down the print head block to close it.  Doing so may cause a 
failure of the print head block or damage to...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.4 RIBBON SAVING MODULE (B-9904-R-QM) 
 
4-17    4.4 RIBBON SAVING MODULE (B-9904-R-QM) 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
NOTE: The ribbon saving module is standard on the B-SX5T series.  
Solenoid (1 pc.) RSV PC Board (1 pc.) Solenoid Harness (1 pc.) Cable Clamp (1 pc.) Locking Support (3 pcs.) 
 · Installation Manual (1 copy) 
· SM-4x8 Screw (2 pcs.) 
  
1) Remove the side...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.4 RIBBON SAVING MODULE (B-9904-R-QM) 
 
4-18   5) Insert folded tag paper (1.5-mm thick) between the print head and the platen, and then turn the 
head lever to Lock position.  Insert the head up arm into the plunger of the solenoid.  While 
holding down the head up arm slightly, lift the solenoid.  Secure the solenoid to the frame with the 
two SM-4x8 screws keeping the solenoid in contact with the spacer.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6)...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.4 RIBBON SAVING MODULE (B-9904-R-QM) 
 
4-19 7) Connect the solenoid harness to CN1 on the RSV PC board and CN11 on the Main PC board.  
Pass the solenoid harness through the cut.  
8) Connect the solenoid cable to CN2 on the RSV PC board.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9) After attaching the solenoid, reassemble the operation panel ass’y and the side panel (L) in the 
reverse order of removal. 
 NOTE: Perform “ FOR FACTORY”...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 
 
4-20 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 
This optional interface board is provided with the two slots, which allows for the use of the two TYPE II 
PC cards.  However, it is not applied to TYPE III PC cards. 
 
CAUTION! 
1. Loosen the two M-3x5 screws of the PCMCIA interface board before installing it.  Failure to do 
this may cause damage to the connector.  
 
 
 
 
 
 
 
 
 
2. When...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 
 
4-21 NOTE: In case of the B-SX5T or the B-SX4T that the optional Expansion I/O board (B-7704-IO-QM) 
has been installed in, remove the expansion I/O board from the printer temporarily using the 
following procedure. 
 (1) Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. 
 (2) Remove the two B-3x6 screws to detach the Expansion I/O board from the printer.  
 
 
 
 
 
 
 
4)...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 
 
4-22 6) Secure the PCMCIA interface board to the PCB support plate with the SM-3x6 screw.   
Tighten the two M-3x5 screws that were loosened previously. (Refer to Caution) 
 
 
 
 
 
 
 
 
 
 
 
7) Attach the blind plate A to the rear plate with the two SM-3x6 screws that were removed in step 6).  
If the LAN interface board or USB interface board is also installed, go to the next step.  
NOTE:...

4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-23 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
This optional interface board is provided with the interface port, which allows for the installation of USB 
devices. 
CAUTION! 
1. Loosen the two M-3x5 screws of the USB interface board before installing it.  Failure to do this 
may cause damage to the connector.  
 
 
 
 
 
 
 
 
 
2. When using the PCMCIA interface board together, first install the...