Toshiba Bsx4t Manual
Have a look at the manual Toshiba Bsx4t Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 566 Toshiba manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.3 STRIP MODULE (B-9904-H-QM) 4-14 10) Connect the longer harness of the rewind full sensor (Tr) and the rewinder harness to CN4 and CN15 on the Main PC board, respectively. NOTES: 1. You should change the selection switch setting depending on the issue mode. Improper setting may affect the print quality. STANDARD/PEEL OFF (STRIP): Batch or strip mode REWINDER: Built-in rewinder mode For the cut mode, the selection switch can be set to either position. 2. The backing paper can be wound directly onto the Take- up Spool or a paper core. When using the Take-up Spool, detach the Holder Stopper by removing the B-3x4 screw. Otherwise, it may be difficult to pull out the wound backing paper roll. When using a paper core, put the core on the Take-up Spool with the Holder Stopper on it, and Attach the top edge of the backing paper to the core with adhesive tape. The Take-up Clip is not necessary. This winding method is applicable to the Built-in Rewinder mode. 11) Open the printer block. (Refer to section 3.3.) 12) Fix the longer harness of the rewind full sensor and the rewinder harness under the Main PC board with the cable clamp. Main PC Board Longer Harness of the Rewind Full Sensor (Tr) CN4 CN15 Selection Switch Cable Clamp Longer Harness of the Rewind Full Sensor (Tr) Rewinder Harness Rewinder Harness Main PC Board Take-up Spool B-3x4 Screw Holder Stopper Take-up Clip
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A
4.3 STRIP MODULE (B-9904-H-QM)
4-15 13) Secure the strip sensor (LED) and strip sensor (Tr) to the printer with the SM-4x8B screws.
14) Connect the shorter harness of the strip sensor (Tr) to the strip sensor harness (for LED).
15) Fix the connected strip sensor harness (for LED) to the base with the cable clamp. While passing
the other strip sensor harness through the cut and the bush, reassemble the operation panel ass’y
to the printer. Then pass the strip sensor harness over the tab on the back of the operation panel
ass’y.
NOTE: Be careful not to pinch the strip sensor harnesses by the operation panel.
SM-4x8B Screw Strip Sensor
(Tr) Strip Sensor
Harness (for LED) Shorter Harness of the Strip
Sensor Harness (for Tr) Strip Sensor (LED) SM-4x8B Screw Tab Strip Sensor (Tr) Bush Strip Sensor Harness (for LED) Cable Clamp Operation Panel Ass’y Strip Sensor Harness Cut
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.3 STRIP MODULE (B-9904-H-QM) 4-16 16) Fix the strip sensor harness with the three cable clamps and connect it to CN20 on the Main PC board. 17) Reassemble the side panel (L) in the reverse order of removal. 18) Close the print head block and ribbon shaft holder plate. NOTE: DO NOT excessively push down the print head block to close it. Doing so may cause a failure of the print head block or damage to the print head. 19) When using the printer in batch mode or strip mode, attach the front plate removed in step 1). 20) When using the printer in built-in rewinder mode, attach the rewinder guide plate to the front of the printer with the two SMW-4x8 screws. 21) Make a test print to check for proper strip issue. NOTE: If the label skews, refer to section 8. Cable Clamp CN20 Main PC Board Strip Sensor Harness Rewinder Guide Plate SMW-4x8 Screw SMW-4x8 Screw
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.4 RIBBON SAVING MODULE (B-9904-R-QM) 4-17 4.4 RIBBON SAVING MODULE (B-9904-R-QM) All the following parts are supplied with the kit. Make sure you have all items shown below. NOTE: The ribbon saving module is standard on the B-SX5T series. Solenoid (1 pc.) RSV PC Board (1 pc.) Solenoid Harness (1 pc.) Cable Clamp (1 pc.) Locking Support (3 pcs.) · Installation Manual (1 copy) · SM-4x8 Screw (2 pcs.) 1) Remove the side panel (L) from the printer. (Refer to section 3.2.) 2) Remove the operation panel ass’y from the printer. (Refer to section 3.4.) 3) Fit the three locking supports into the RSV PC board. 4) Secure the RSV PC board to the printer with the locking support. NOTE: Do not push the center of the RSV PC board when attaching it to the printer. Doing so may break the PC board. Hold the locking supports and push them into the holes for securing the RSV PC board. RSV PC Board Locking Support RSV PC Board Holes for securing the RSV PC Board Locking Support
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.4 RIBBON SAVING MODULE (B-9904-R-QM) 4-18 5) Insert folded tag paper (1.5-mm thick) between the print head and the platen, and then turn the head lever to Lock position. Insert the head up arm into the plunger of the solenoid. While holding down the head up arm slightly, lift the solenoid. Secure the solenoid to the frame with the two SM-4x8 screws keeping the solenoid in contact with the spacer. 6) Attach the cable clamp to the frame of the printer. Fix the solenoid cable with this cable clamp. NOTE: Be careful not to snag the solenoid harness when running it. Frame SM-4x8 Screw Head Up Arm Plunger Solenoid Spacer Cable ClampSolenoid Cable Solenoid Solenoid Harness
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A
4.4 RIBBON SAVING MODULE (B-9904-R-QM)
4-19 7) Connect the solenoid harness to CN1 on the RSV PC board and CN11 on the Main PC board.
Pass the solenoid harness through the cut.
8) Connect the solenoid cable to CN2 on the RSV PC board.
9) After attaching the solenoid, reassemble the operation panel ass’y and the side panel (L) in the
reverse order of removal.
NOTE: Perform “ FOR FACTORY” of system mode to make sure the solenoid performs
properly.
CN2
CN1 Solenoid Cable CN11 Main PC Board
Solenoid Harness RSV PC Board Cut
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 4-20 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) This optional interface board is provided with the two slots, which allows for the use of the two TYPE II PC cards. However, it is not applied to TYPE III PC cards. CAUTION! 1. Loosen the two M-3x5 screws of the PCMCIA interface board before installing it. Failure to do this may cause damage to the connector. 2. When using the LAN interface board or USB interface board together, install the PCMCIA interface board first. NOTE: When both B-9700-PCM-QM and B-9700-LAN-QM are installed, inserting a LAN PC card into the slot of the B-9700-PCM-QM disables the B-9700-LAN-QM. All the following parts are supplied with the kit. Make sure you have all items shown below. PCMCIA Interface Board (1 pc.) 1) Remove the side panel (L) from the printer. (Refer to section 3.2.) 2) Loosen the two M-3x5 screws of the PCMCIA interface board. (Refer to Caution above.) 3) Remove the two SM-3x6 screws to detach the blind plate A from the back. M-3x5 Screw · Installation Manual (1 copy) · SM-3x6 Screw (3 pcs.) Rear Plate SM-3x6 Screw Blind Plate A
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 4-21 NOTE: In case of the B-SX5T or the B-SX4T that the optional Expansion I/O board (B-7704-IO-QM) has been installed in, remove the expansion I/O board from the printer temporarily using the following procedure. (1) Disconnect the Expansion I/O cable from CN1 on the Expansion I/O board. (2) Remove the two B-3x6 screws to detach the Expansion I/O board from the printer. 4) Firmly connect CN101 on the PCMCIA interface board directly to CN7 on the Main PC board. 5) Secure the PCMCIA interface board to the rear plate with the two SM-3x6 screws. PCMCIA Interface Board Main PC Board CN101 CN7 SM-3x6 Screw Rear Plate Rear Plate B-3x6 Screw Expansion I/O Board CN1 Expansion I/O Cable
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.5 PCMCIA INTERFACE BOARD (B-9700-PCM-QM) 4-22 6) Secure the PCMCIA interface board to the PCB support plate with the SM-3x6 screw. Tighten the two M-3x5 screws that were loosened previously. (Refer to Caution) 7) Attach the blind plate A to the rear plate with the two SM-3x6 screws that were removed in step 6). If the LAN interface board or USB interface board is also installed, go to the next step. NOTE: Keep the two SM-3x6 screws and blind plate A safe when the LAN interface board or USB interface board is installed. 8) Reassemble the side panel (L) in the reverse order of removal. If the Expansion I/O board was removed at the beginning, reassemble it. NOTE: For inserting, removing, and handling the PC card, refer to the Owner’s Manual. Blind Plate A SM-3x6 ScrewRear Plate SM-3x6 screw PCB Support Plate M-3x5 Screw
4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 4.6 USB INTERFACE BOARD (B-9700-USB-QM) 4-23 4.6 USB INTERFACE BOARD (B-9700-USB-QM) This optional interface board is provided with the interface port, which allows for the installation of USB devices. CAUTION! 1. Loosen the two M-3x5 screws of the USB interface board before installing it. Failure to do this may cause damage to the connector. 2. When using the PCMCIA interface board together, first install the PCMCIA PC board, and then USB interface board. All the following parts are supplied with the kit. Make sure you have all items shown below. USB Interface Board (1pc.) PCB Attachment Plate (1 pc.) NOTE: When using the PCMCIA interface board (B-9700-PCM-QM) together, the PCB attachment plate will be used. 1) Turn the power off and disconnect the power cord. 2) Loosen the two M-3x5 screws of the USB interface board. (Refer to Caution above.) 3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 4) Remove the two SM-3x6 screws to detach the blind plate A from the back. M-3x5 Screw · Installation Manual (1 copy) · SM-3x6 Screw (4 pcs.) SM-3x6 Screw Blind Plate A