Toshiba Bsx4t Manual

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-24   5) If the PCMCIA interface board is used together with the USB interface board, attach the PCB 
attachment plate to the plate to which the PCMCIA interface board is secured with the SM-3x6 
screw.  If not, go to the next step.  
 
 
 
 
 
 
 
 
 
 
 
 
6) Firmly connect CN50 connector on the USB interface board directly to CN7 on the Main PC board 
or CN1 on the PCMCIA interface board.  
 When connecting to the Main PC Board: When connecting the PCMCIA Interface Board:  PCMCIA Interface Board  PCB Attachment Plate SM-3x6 Screw USB Interface Board Main PC Board  CN50 CN7 USB Interface Board PCMCIA Interface Board  CN50 CN1  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-25   7) Secure the USB interface board to the rear plate with the two SM-3x6 screws.  
 
 
 
 
 
 
 
 
 
 
 
 
 
8) Tighten the two M-3x5 screws of the USB interface board that were loosened previously. 
(Refer to Caution) 
9) Secure the USB interface board to the PCB support plate (when connecting to the Main PC board) 
or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 
screw. 
 When connecting to the Main PC Board: When connecting to the PCMCIA Interface Board:   SM-3x6 Screw USB Interface Board   SM-3x6 Screw USB Interface Board When connecting to the Main PC Board: M-3x5 Screw  SM-3x6 ScrewPCB Support Plate When connecting to the PCMCIA Interface Board: M-3x5 Screw   SM-3x6 Screw PCB Attachment 
Plate  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.6 USB INTERFACE BOARD (B-9700-USB-QM) 
 
4-26  10) Attach the blind plate A to the rear plate.  If the PCMCIA interface board has been installed,  
 go to the next step.  
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: In case that the PCMCIA interface board has been installed, retain the blind plate A.  
 
11) Reassemble the side panel (L) to the printer in the reverse order of removal.  
 
 
 Blind Plate A  SM-3x6 Screw Rear Plate 
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-27 4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
This optional interface board enables the printer to be used in a LAN network. 
CAUTION! 
1. Loosen the two M-3x5 screws of the LAN interface board before installing it.  Failure to do this 
may cause damage to the connector.  
 
 
 
 
 
 
 
 
 
2. When using the PCMCIA interface board together, first install the PCMCIA PC board, and then 
LAN interface board.  
 
 
 
NOTE: When both B-9700-LAN-QM and B-9700-PCM-QM are installed, inserting a LAN PC card into 
the slot of the B-9700-PCM-QM disables the B-9700-LAN-QM. 
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
LAN Interface Board (1pc.) 
 
 
 
 
 
 
 PCB Attachment Plate NOTE: When using the PCMCIA interface board (B-9700-PCM-QM) together, the PCB attachment 
plate will be used. 
   M-3x5 Screw License Agreement 
Please be sure to read the License Agreement before opening the sealed LAN Interface Board.  If you do not 
agree with the License Agreement, please do not use this product.  Your unpacking the product indicates your 
approval for the License Agreement.    · Installation Manual (1 copy) 
· License Agreement (1 copy) 
· SM-3x6 Screw (4 pcs.)  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-28 1) Loosen the two M-3x5 screws of the LAN interface board. (Refer to Caution above.) 
2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
3) Remove the two SM-3x6 screws to remove the blind plate A from the back. 
 
 
 
 
 
 
 
 
 
 
 
 
NOTE: Keep the blind plate A safe as this will be necessary when the machine is modified to the 
standard type. 
 
4) If the PCMCIA interface board is also installed, attach the PCB attachment plate to the plate to 
which the PCMCIA interface board is secured with the SM-3x6 screw.  If not, go to the next step. 
 
   Blind Plate A SM-3x6 Screw  PCB Attachment PlateSM-3x6 Screw PCMCIA Interface Board  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-29 5) Firmly connect CN50 on the LAN interface board directly to CN7 on the Main PC board or CN1 on 
the PCMCIA interface board.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
6) Secure the LAN interface board to the rear plate with the two SM-3x6 screws. 
 
 When connecting to the Main PC Board When connecting to the PCMCIA Interface Board  LAN Interface Board MAIN PC BoardCN50 CN7   LAN Interface Board PCMCIA Interface Board CN50 CN1 When connecting to the Main PC Board When connecting to the PCMCIA Interface Board   SM-3x6 
Screw SM-3x6 
Screw Rear PlateRear Plate LAN Interface Board LAN Interface Board  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.7 LAN INTERFACE BOARD (B-9700-LAN-QM) 
 
4-30  7) Tighten the two M-3x5 screws on the LAN interface board that were loosened previously. 
(Refer to Caution.) 
8) Secure the LAN interface board to the PCB support plate (when connecting to the Main PC board) 
or PCB attachment plate (when connecting to the PCMCIA interface board) with the SM-3x6 
screw. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9) Reassemble the side panel (L) in the reverse order of removal.  
 
NOTE: Precaution for the LAN cable connection 
 When connecting a LAN cable with the hooded connectors to the LAN interface board, it may 
not be connected depending on the shape of the hood.  In this case, move aside the hood, 
connect the cable, and return the hood to the former position.  
 
 
 When connecting to the Main PC Board  M-3x5 ScrewSM-3x6 Screw PCB Support Plate When connecting to the PCMCIA Interface Board   M-3x5 ScrewSM-3x6 Screw PCB Attachment Plate  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
 
4-31 4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
This optional interface board is provided with an expansion I/O interface. 
NOTE: The expansion I/O interface board is standard on the B-SX5T series.  
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Expansion I/O Board (1 pc.) Expansion I/O Cable (1 pc.) 
  Installation Manual (1 copy) 
 Locking Support WLS-16-0 (1 pc.) 
NOTE: The locking support is not used on this printer.  
 
1) Turn the power off and disconnect the power cord. 
2) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
3) Remove the two M-3x6 screws and detach the blind plate B from the back. 
 
 
 
 
 
 
 
 
 
4) Remove the two B-3x6 screws from the expansion I/O board.  
 
   Blind Plate B M-3x6Screw  B-3x6 Screw   
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.8 EXPANSION I/O INTERFACE BOARD (B-7704-IO-QM) 
 
4-32 5) Connect the expansion I/O cable to CN3 on the Main PC board.  
 
 
 
 
 
 
 
 
 
 
6) Secure the expansion I/O board to the rear plate with the two B-3x6 screws removed in Step 4. 
7) Connect the expansion I/O cable to CN1 on the expansion I/O board.  
 
 
 
 
 
 
 
 
 
 
 
8) Reassemble the side panel (L) in the reverse order of removal.  
9) Perform a loop back check to confirm that the expansion I/O board functions properly.  
 
   Expansion I/O Cable CN3 Main PC Board   CN1 Expansion I/O Board Expansion I/O Cable B-3x6 ScrewRear Plate  
						

							5. SYSTEM MODE  EO18-33012A 
 
5.1 OPERATION PANEL
 
5-1 
5. SYSTEM MODE 
This chapter describes usage and purpose of the keys on the Operation Panel in System Mode. 
For service personnel, System Mode should be used for the following eight purposes: 
· To check and print the system status, the Maintenance Counter, and the Print Head Element. 
· To set the parameters for the communication with the host computer, and the printer functions 
such as the keys and LCD Message Display. 
· To make fine adjustment related to the media issue. 
· To perform a test print for checking print quality. 
· To check the status of the sensors and to set the threshold of the media sensors. 
· To perform a Maintenance Counter clear and Parameter clear. 
· To set the IP Address. 
· To set the Basic setting. 
· To perform the factory mode. 
 
5.1 OPERATION PANEL 
The figure below illustrates the Operation Panel and key functions. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the 
printer’s status.  Up to 16 characters in 2 lines can be displayed. 
 
There are three LEDs on the Operation Panel. 
LED Illuminates when… 
POWER  The printer is turned on. 
ON LINE  The printer is ready to print. 
ERROR  Any error occurs with the printer. 
 
In System Mode, the [FEED], [RESTART] 
and [PAUSE]
 keys function as described below. 
FEED Used to start the system mode as a [PAUSE]
 key does.  Used to select the 
parameter mode or to fine adjust the parameters in the negative direction (-). 
RESTART Used to select the parameter mode or to fine adjust the parameters in the positive 
direction (+). 
PAUSE Used to start the system mode as a [FEED]
 key does and to select the parameter 
mode.  Used as an enter key. 
NOTE: Use the [RESTART] key to resume printing after a pause condition, or after clearing an error. 
LCD Message Display 
(16 characters x 2 lines) 
ON LINE LED (Green) 
ERROR LED (Red) 
[PAUSE]
 key  POW ER LED (Green) 
[FEED]
 key 
[RESTART]
 key ON L I N E
B- SX4T V1 0A