Toshiba Bsx4t Manual

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 4 4.1 SWING CUTTER (B-4205-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. This optional device is used for cut print, which cannot be used together with either B-8204-QM or B-
9904-H-QM. 
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Cutter Unit (1 pc.) Cutter Cover (1 pc.) Cutter Harness (1 pc.) Print Head Cleaner (1 pc.) 
(P/No.: FMQB0051601) Cutter Attachment Screw  
(2 pcs.) 
 
 
 Bush (1 pc.) 
· Installation manual (1 copy) 
· FL-4x6 Screw (1 pc.)  
1) Remove the two black screws to detach the front plate. 
 
 
 
 
 
 
 
 
 
 
NOTE: Retain the two black screws and front plate.   Cutter Blade         Front Plate Black Screws  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 5 2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Open the printer block. (Refer to Section 3.3.) 
5) Attach the cutter unit to the front of the printer with the cutter attachment screws and the FL-4x6 
screw. 
 
 
 
 
 
 
 
 
 
 
 
6) Connect the cutter harness to CN1 on the cutter I/F PC board. 
7) Fit the bush to the cutter harness in the orientation shown below. 
 
 
 
 
 
 
 
 
 
 
 
8) Insert the cutter harness into the gap between the cutter unit and the printer, and then into the 
hole in the main frame.  Fit the bush into the hole.  
 
 
 
 
 
 
 
 
 
    Cutter Attachment Screw FL-4x6 ScrewCutter Unit   CN1 
Cutter Harness  Cutter I/F 
PC Board   Bush Cutter Harness  Hole  Main Frame  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.1 SWING CUTTER (B-4205-QM) 
 
4- 6   9) Close the print head block and the ribbon shaft holder plate.  
NOTE: DO NOT excessively push down the print head block to close it.  Doing so may cause a 
failure of the print head block or damage to the print head. 
10) Connect the cutter harness to CN15 on the Main PC Board.  
 
 
 
 
 
 
 
 
 
 
 
11) Fit the cutter cover on the cutter attachment screws, and fix it to the cutter unit with the two cutter 
screws.  
NOTE: Be careful not to pinch the cutter harness by the cutter cover. 
 
 
 
 
 
 
 
 
 
 
 
 
12) Reassemble the side panel (L) and close the top cover.  Finally check the cutter operation. 
NOTE: For cleaning the cutter, refer to section 8.  CN15  Main PC Board 
Cutter Harness  Cutter Screw Cutter Attachment Screw  Cutter Cover  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 7 4.2 ROTARY CUTTER (B-8204-QM) WARNING! Be careful not to injure your fingers when installing the cutter unit. This optional device is used for cut print, which cannot be used together with either B-4205-QM or B-
4905-H-QM. 
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Cutter Unit (1 pc.) 
 
 
 
 
 
 Cutter Cover (1 pc.) Cutter Drive Unit (1 pc.) Harness Ass’y 
(2-pin & 9-pin) (1 pc.) Cord Bush (1 pc.) 
 Print Head Cleaner (1 pc.) 
(P/No.: FMQB0051601) · Installation Manual (1 copy) 
· SM-4x8 Screw (6 pcs.)    Cutter Blade        
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 8 1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 
2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Fix the cutter drive unit to the printer with the three SM-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
5) Connect the 9-pin connector of the harness ass’y to CN7 and 2-pin connector to CN9 on the cutter 
driver unit, respectively. 
 
 
 
 
 
 
 
 
 
 
 
6) Fit the bush to the harness ass’y in the orientation as shown below. 
   SM-4x8 Screw Cutter Drive Unit SM-4x8 Screw  CN7 (9 pins) CN9 (2 pins) Harness Ass’y  BushHarness Ass’y  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4- 9 7) Insert the harness ass’y into the hole in the main frame.  Fit the bush into the hole. 
 
 
 
 
 
 
 
 
 
 
 
8) Connect the 9-pin connector of the harness ass’y to CN15, and 2-pin connector to CN18 on the 
Main PC board, respectively.  
 
 
 
 
 
 
 
 
 
 
 
 
9) Open the printer block. (Refer to section 3.3.) 
10) Connect the four harnesses of the cutter unit to CN8, CN10, CN11 and CN12 on the cutter drive 
unit.  Main PC BoardCN18 (2 pins) CN15 (9 pins)Harness Ass’y Hole  Main Frame Harness Ass’yCutter Unit   Cutter Drive Unit Print Head Block CN8 CN12 CN10 CN11  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.2 ROTARY CUTTER (B-8204-QM) 
 
4-10 11) Fit the two tabs of the cutter drive unit into the notches, and then fix the cutter unit with the three 
SM-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
12) Attach the cutter cover to the cutter unit with the two screws so that the tab of the cutter cover 
turns on the cutter cover open switch. 
 NOTES: 1. Be careful not to pinch the cutter harness by the cutter cover. 
  2. Make sure that the anti-static brush is protruding from the media outlet.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
13) Close the print head block and ribbon shaft holder plate.  
NOTE: DO NOT excessively push down the print head block to close it.  Doing so may cause a 
failure of the print head block or damage to the print head. 
14) Reassemble the side panel (L) and close the top cover.  Finally check the cutter operation. 
     Cutter Unit Notch Tab SM-4 x 8 Screw Notch Tab SM-4 x 8 Screw    Screw Cutter Cover Anti-static Brush Media Outlet Tab Cutter Cover Open Switch Cutter Cover  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-11 4.3 STRIP MODULE (B-9904-H-QM) 
This optional device is used for strip print, which cannot be used together with either B-4205-QM or B-
8204-H-QM. 
 
NOTE: The strip module is standard on the B-SX5T series.  
 
All the following parts are supplied with the kit.  Make sure you have all items shown below. 
Rewinder Ass’y (1 pc.) 
 
 
 
 
 
 Rewinder Guide Plate (1 pc.) Bush (1 pc.) 
 Strip Sensor (TR) (1 pc.) Strip Sensor (LED) (1 pc.) Rewind Paper Guide (1 pc.) 
 
 
 
 
 · Installation Manual (1 copy) 
· SM-4x8B Screw (10 pcs.) 
· SM-3x6B Screw (1 pc.) 
· SM-4x8C Screw (1 pc.) 
        
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-12   1) Remove the two black screws to detach the front plate. (Refer to section 4.1.) 
2) Open the top cover. (Refer to Section 3.1.) 
3) Remove the side panel (L) from the printer. (Refer to section 3.2.) 
4) Remove the operation panel ass’y from the printer. (Refer to section 3.4.) 
5) Attach the rewind paper guide to the base with the two M-4x8 screws. 
 
 
 
 
 
 
 
 
 
 
 
6) Align the notch of the take-up holder with the screw hole of the rewinder ass’y, and attach them to 
the printer with the four SM-4x8B screws and the SM-4x8C screw. 
7) Attach the rewind full sensor (LED) to the base with the SM-3x6B screw. 
  Screw Hole Rewind Paper Guide M-4x8 Screw  
						

							4. INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO18-33012A 
 
4.3 STRIP MODULE (B-9904-H-QM) 
 
4-13  8) Fit the bush to the longer harness of the rewind full sensor (Tr) and the rewinder harness in the 
orientation shown below.  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
9) Insert the longer harness of the rewind full sensor (Tr) into the hole in the printer frame.  Fit the 
bush into the hole.  
    SM-4x8B Screw SM-4x8C ScrewSM-4x8B Screw Take-up Holder Notch Rewind Full Sensor (LED) SM-3x6B Screw Rewinder Ass’yBase Bush Longer Harness of the Rewind  
Full Sensor (Tr)    Longer Harness of the Rewind 
Full Sensor (Tr)  Bush Hole Frame Rewinder Harness