TiE Onyx 2, 3, 4, 5 Service And Programming Manual

E- TRUNKS
El- PORT NUMBER
Description
Use this option to change the port assignment for a trunk. The port is the
hardware location of the trunk. When you change a trunk’s port number, all
programming for the trunk goes to the new port assignment (location). All
trunks use a single port.
Keep the following in mind when programming ports:
oUse HH- Port/Extension Checker to make sure each port has only one
assigned trunk
Do not swap an extension port with a trunk port.
o You can optionally Use...

E- TRUNKS
 CIRCUIT TYPE
Description
Use this option to identify the type of trunk connected to each trunk port. The
trunk circuit type choices are:
05 OPX, 
   and  ports (see E- Extension programming)
07 DID trunk
08 CO trunk. ground start. 
09 CO trunk, ground start, DP (Dial Pulse)’
10 CO trunk, loop start. DTMF
11 CO trunk, loop start, DP
12 DISA trunk. DTMF, day or night*
13 DISA trunk, DP. day or 
14 DISA trunk. DTMF. night only’
15 DISA trunk. DP, night 
16 Tie trunk, DTMF, wink 
17 Tie trunk, DP,...

E- TRUNKS
 CIRCUIT TYPE
Feature Reference
Instructions
Step  
Step  l
Step 2 
Step 3 l
Refer to Programming in the following features:
Background Music
Centralized Attendant 
Central Office Calls. Answering
Central Office Calls. Placing
DP and DTMF Compatibility
Direct Inward Dialing
Direct Inward System Access
Music On Hold
Off-Premise Extension
Paging
Private Line
Special Services and OCC Compatibility
Tenant Service
Tie Lines
Voice Mail Compatibility
To enter data on the 
PRF:
Enter the circuit type...

E- TRUNKS
  CIRCUIT NUMBER
Description
Related
Programming
l
l
l
l
Z-152  CONFIGURATIONIssue  
Use this option to assign the associated  circuit number for each 
DID and tie trunk. Refer to the  Installation and Programming Manual for
charts and drawings that explain this association. This option does not 
 
.
Conditions
This option only applies to OPX. DID and tie trunks.
Default Value
No  circuit number assigned (00).
Centralized Attendant Service
CP- Allow Bell Standard for CAS (BYO:O) 
 Enable this...

 TRUNKS
  CIRCUIT NUMBER
Related
l
l
P
P
P
Feature Reference
Instructions
Step  
Step  l
Step  
Issue 1-O
KS- Programming  for   Each extension should have a line key
for DID trunks or a loop key.
Off-Premise Extension
E- Trunks, 
 Circuit Type  OPX extensions use circuit type 05.
Remember that OPX extensions use trunk numbers.
Tie Lines
CP- Absorb 1st Digit for DID and Tie Trunks   For incoming
wink start tie trunk calls, enable/disable 1st digit absorption. If enabled,
system ignores first incoming...

E- TRUNKS
 CLASS  SERVICE
Description
Related
Programming
Feature Reference
Instructions
Step  l
Step  
Step 2 l
Step 3 l
Use this option to assign a Class of Service (COS) to each DID, DISA and tie
trunk. You can use COS to put dialing restrictions on incoming DISA and tie
trunk callers.
Conditions
This option only applies to DID, DISA and tie trunks.
Default Value
All trunks have COS 00.
Refer to Programming in the features listed below.
Refer to Programming in the following features:
Centralized...

E- TRUNKS
 NEXT TRUNK IN OUTBOUND ROTARY (HYBRID ONLY)
Description
Use this option to determine the selection sequence for trunks within a trunk
rotary. The trunk rotary 
 the order of the list vou create using this
option. When entering data. make sure the last 
 in the rotary  not
loop back to the first. You can program CO, DISA and tie trunks into an
outbound  rotary. Normally. only trunks of the same 
 are in the same
rotary.
For example, to program a trunk rotary using trunks 480, 481 and 482:
For...

E- TRUNKS
 NEXT TRUNK IN OUTBOUND  (HYBRID ONLY)
Related
Programming
(Cont’d)
l
l
Feature Reference
Instructions
Step 1 l
Step 1 
Step 2 
Step 3 l
Centralized Attendant Service
CP- Allow 
 Standard for    Enable this option if hub
system is using Bell Standard Centralized Attendant Service. Disable this
option if hub is a 
 PBX.
E- Trunks,  Circuit Type  Assign each tie trunk used for CAS one of the
following circuit types:
16 DTMF Wink Start tie line
17 Dial Pulse Wink Start tie line
18 DTMF Immediate...

E- TRUNKS
 TRUNK SERVICE NUMBER
Description
Related
Programming
l
If the system has ARS or LCR. use this option to assign a Service Number to
trunks. Trunks of the same type should have the same Service Number. You
can assign a trunk one of 10 
 Numbers (l-10). When routing calls,
ARS and LCR will:
 Analyze the digits a user dials
 Choose a  Number for the call
Route the call on the first available trunk with the selected Service
Number.
You can also use this option to designate a trunk as a PBX trunk...

E- TRUNKS
 TRUNK SERVICE NUMBER
Related
Programming
(Cont’d)
l
Feature Reference
Instructions
Step  l
Step  
Step 2 l
Step 3 
QL-  Codes,  of Service  Enter the type of service
number (O-5). For example. for DDD or WATS, enter 
QL-  Codes. Access Code  For dial-up services. enter
the access code (telephone number) for the service.
QL- 
 Codes,  Code  For dial-up services, enter
the security code the service requires.
 
QB- PBX Access Codes  Designate up to 11 PBX access codes.
Automatic Route Selection...