TiE Onyx 2, 3, 4, 5 Service And Programming Manual

E- EXTENSIONS
EU- MAILBOX ACCESS CODE, REPETITIVE (ONYX IV)
Description
If you enter the Voice Mail master number for EU- Repetitive 
Extension, this option lets you set the mailbox that plays the announcement
while ACD callers wait. (In 1002, this is a Node Mailbox. Make sure you set
all Node Mailbox options to Exit. Refer to the Voice Mail documentation for
the specifics on programmin g Node Mailboxes.) You 
can only use this
option if you enter the Voice Mail master numberfor EU- Repetitive...

E- EXTENSIONS
EU- PLAYBACK INTERVAL WITH 
 (ONYX IV)
Description
If you enter the Voice Mail master number for EU- Repetitive Announcement
Extension, use this option to set how often VX should repeat the Repetitive
Announcement Message. The range is O-255 (where 
 seconds). If you
enter 0, the wait is 1 
 and 30 seconds. You can  use this option if
 enter the   master number for EC’-  Announcement
Extension.
This option only applies to ONYX IV.
Conditions
None
Default Value
1 minute, 30 second wait (0)...

E- 
EY- COPY  ACCESS   CONTROL
Description
Related
Programming
Feature Reference
Instructions
Step 1 Refer to the data you entered for the ED option.
Step  
Step  l
Step 3 
Step  
Step 5 l
Step 6 l
Use this option to  the ED- Ring. Access and  Control
programming from one  to another. Use this option only to 
data. You cannot enter ED data with this option.
Conditions
None
Default 
None
None
None
To enter data on the PRF:
To enter data at the programming terminal:
Type EY. You see: 
COPY RING CONTROL?
To...

E- EXTENSIONS
 EXTENSION-PORT SWAP
Description
Related
Programming
Feature Reference
Use this option to change the  assignment for a port.  port
is the hardware location of the 
 When you change a port
number, all programming for the 
 goes to the new port
assignment (location).
All 
 use a single port. except for Data Sets,  and DSS
Consoles. These are dual-port 
 that use a port pair. A port pair
consists of two consecutive ports. beginning with an even numbered port (e.g.
00 and 01). When changing a...

E- EXTENSIONS
EZ- EXTENSION-PORT SWAP
Instructions
Step  l
Step 1 l
Step  
Step 3 
Issue 1-O
To enter data on the PRF:
Enter the port 
 for each extension on Table 
To enter data at the programming terminal:
Type 
 You see: PORT 00
Press RETURN to program port 00.
OR
Enter another port number (00-79) and press RETURN. In either case, you see:
EXT
Enter data for this option from Table  and press RETURN.
You advance to the next consecutive port.
 CONFIGURATIONZ-143 

E- EXTENSIONS
EZ- EXTENSION-PORT SWAP
 For   
Issue 1-O 

E- TRUNKS
EO- ALL DATA
Description
Use EO to enter data for all options sequentially for a trunk. The charts below
show the 
 options that correspond to each EO entry. Refer to these options
for more information. Also, the charts below show the default value for each
option (where applicable).
EO Prompts for CO Trunks
For this option...
EXTPORT
CIRCUIT TYPE cos 01 NEXT LINE IN ROTARY
SERVICE # DIR TERM OR OPR EXTFIRST LINE IN GROUP
CALL PICKUP GROUP NIGHT CALL TO EXTTANDEM OK N [Y/N] 
TOLL RESTRICT Y...

E- TRUNKS
EO- ALL DATA
Description
(Cont’d)
EO Prompts for DISA Trunks
For this option...
EXT
PORT
CIRCUIT TYPE (12-15)
cos  
NEXT EXT IN HUNTSERVICE # ALLOW LINE DIAL-UP Y [Y/N] 
ACCESS TO GROUP  Y [Y/N] throughACCESS TO GROUP  Y [Y/N] DIR TERM OR OPR EXT UCD MASTER EXT
SPD DIAL BLOCXCALL PICKUP GROUP ACCESS CONTROL
COPY? 
 [Y/N] LINES 1 TO8 YYYY YYYY through
 YYYY YYYY CALL-OUT CONTROL
COPY?  [Y/N] LINES 8YYYY
YYYY through65 TO72 Y Y Y Y Y Y Y Y LOOP  (ONYX IV)
PRIORITY (ONYX IV)
Look here...
El
E2
E3...

 TRUNKS
EO- ALL DATA
Description
(Cont’d)
Issue 1-O
EO Prompts for Tie Trunks
For this option...
EXT
PORT
CIRCUIT TYPE (16-19)
  00 cos 01 
NEXT EXT IN HUNTSERVICE # ALLOW LINE DIAL-UP Y [Y/N] ACCESS TO GROUP  Y [Y/N] through
ACCESS TO GROUP  Y [Y/N] DIR TERM OR OPR EXT UCD MASTER EXT 
SPD DIAL BLOCKCALL PICKUP GROUP ACCESS CONTROL
COPY? 
 [Y/N] LINES 1 TO8 YYYYYYYY through
6 5   TO72 YYYY YYYY 
CALL-OUT CONTROLCOPY?  [Y/N] 
LINES 1 TO8 YYYYYYYY 
through
65 TO 72YYYYYYYY 
LOOP NUMBER (ONYX IV)
PRIORITY...

E- TRUNKS
EO- ALL DATA
Related
Programming
Feature Reference
Instructions
Step 1 
Step 
Step 2 
Step 3 l
Refer to the charts above.
Refer to the individual E options.
To enter data on the PRF:
Refer to the individual E options.
To enter data at the programming terminal:
Type 
EO.
Enter the number of the trunk you want to program and press RETURN. You
see: 
PORT
Enter data for this option from Table 5.After you enter data for one option, you automatically advance to the next option.
2-148 SOFTWARE...