TiE Onyx 2, 3, 4, 5 Service And Programming Manual

E- TRUNKS
 DIRECT TRUNK TERMINATION
Description
Use this option to set the termination for a trunk. If the termination is an
attendant:
For a CO trunk, this option sets the attendant that controls Night Answer
for the trunk
For a tie trunk, this option sets the attendant the incoming tie trunk caller
reaches when they dial 0
The termination can also be:
An extension or Ring Group (see the Direct Inward Lines feature)
An ACD or UCD Group master number (see the Automatic Call
Distribution and Extension...

E- TRUNKS
 DIRECT TRUNK 
Related
on
l
l
l
Centralized Attendant Service
CP- Allow Bell Standard for CAS 
  Enable this option if hub
system is using Bell Standard Centralized Attendant Service. Disable this
option if hub is a 
 PBX.
E- Trunks. 
 Circuit   Assign each tie trunk used for CAS one of the
following circuit types:
16 DTMF Wink Start tie line
17 Dial Pulse Wink Start tie line
18 DTMF Immediate Dial tie line
19 Dial Pulse Immediate Dial tie line
E- Trunks, 
  Circuit Number  Enter the  circuit...

E- TRUNKS
 DIRECT TRUNK TERMINATION
Issue 1-O
For Your Notes
 CONFIGURATION  

E- TRUNKS
 DIRECT TRUNK 
Related
Programming
(Cont’d)
l
l
l
Direct Inward Line
KS- Programming 
 for  A  to a  should ring a key.
If the trunk doesn’t 
 a line  it  ring a loop key.
 Answer
 Extensions.  Do Not Disturb (DND)  Allow DND at each attendant
that should be able to 
 Night Answer.
 Answer, Universal Sight Answer
E- Extensions. ED- Trunk Control, Access Control 
 An extension has
UNA pickup only for trunks to which it has access. (ED- Ring Control
programming has no effect on 
 answering.)
E-...

E- TRUNKS
 DIRECT TRUNK TERMINATION
l
l
l
l
l
l
Feature Reference
Instructions
Step 1 l
Step 1 l
Step 2 
Step 3 l
Issue 1-O
QT- System Timers, OPA Overflow Ring Control  Indicate the number of
rings (3-15) before operator overflow to the 
OPA occurs. This pertains only
to operator overflow calls.
Voice Mail Compatibility
E- Extensions, 
 Circuit Type  Each OPX and AS1 P/N 89748 Voice
Messaging System port should have circuit type 05. Each AS1 P/N 89749
Voice Messaging System port should have circuit type...

 TRUNKS
EA- TRUNK GROUP ASSIGN. (FIRST TRUNK IN GROUP), HYBRID
Description
Note:
Related
Programming
P
P
P
P
P
P
l
l
P
l
Use this option to group trunks by assigning  them the same First Trunk in
Group number. Remember. you normally put only trunks of the same type in
the same group.
When programming DISA and tie trunks, use this option instead of  EA
(Extensions)- UCD Group Master Extension Number.
This prompt appears in the key systems, but has no significance.
Conditions
Although this option appears...

E- TRUNKS
EA- TRUNK GROUP ASSIGN. (FIRST TRUNK IN GROUP), HYBRID
Related
Programming
Feature Reference
Instructions
Step 1 
Step  l
Step 2 
Step 3 
Issue 1-O .
Line (Trunk) Rotaries
E- Extensions, ES- Line Access Options, Access To Groups 90-95 
Allow/deny access to each of the first 6 trunk groups  You cannot
program this option for trunk groups 96-98.
E- Trunks,  Next Trunk in Outbound Rotary  This determines the
selection sequence for trunks within the rotary. Make sure the last trunk in
the rotary...

E- TRUNKS
EC- CALL PICKUP GROUP
Description
Use this option to assign a trunk to a Call Pickup Group (01-23). To assign an
extension to a Call Pickup Group, refer to EC (Extensions)- Call Pickup
Group.
Conditions
Although this prompt appears for DID trunks, it is not used.
Default Value
Trunks not assigned to  Pickup Groups (00).
Related
Programming
None
Feature Reference
Instructions
Step 1 
Step 
Step 2 l
Step 3 
Group Call Pickup
To enter data on the PRF:
Enter the Call Pickup Group number for each...

E- TRUNKS
EI- NIGHT CALL ROUTING
Description
Related
Programming
Use this option to define the night call route for each trunk. The night route
can be an extension or a ring group. The trunk uses this route when the
trunk’s attendant activates Night Answer. This option overrides ED- Ring
Control assignments at night. It also lets night mode calls ring 
extensions.
Conditions
This option does not apply to tie trunks. This option only applies to DISA
trunks or a DIL when the called extension is in Do Not...

E- TRUNKS
EI- NIGHT CALL ROUTING
Related
Programming
(Cont’d)
Operator Assistance
 have OPA answer the trunk...
E- Trunks, 
 Direct Trunk Termination  To have OPA intercept
incoming calls on a trunk day and night, enter the number of the first port on
the 
 PCB. Intercept occurs after the first ring.
To configure the OPA dialing and message options...
CP- Inhibit OPA Transfers to Extension 
  Allow/deny OPA
Transfers to extensions with this Class of Service.
E- Extensions,  Class of Service  Assign Class...