Home > Singer > Sewing Machine > Singer Serger Professional 5 Manual

Singer Serger Professional 5 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Singer Serger Professional 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Singer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							33
    9
    10
    11
    81
    7
    5
    6
    4
    3
    2 1
    2 2
    3) Threading the
    (Brown)
    Chain Stitch/Cover stitch Looper
    20
    While holding thread with fingers, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the tension
    discs 3.
    Thread the chain stitch/cover stitch looper as indicated
    1~11.
    Thread the top cover
    thread guide by pulling
    the thread towards the
    left until it slips under
    guide. Then pull thread
    along the right side of
    button as illustrated. Pass thread from back to the front through the
    thread guide 1. Raise Presser foot by lowering presser bar lifter to
    release Tension discs. 
    						
    							92
    7 5
    8
    6
    43
    1
    10 11
    8
    7
    9
    6
    4
    5
    C
    A
    BD
    21
    Thread the right needle as indicated 1~9.Turn the hand wheel toward you until the chain stitch
    looper extends out 10mm from the needle plate
    edge.
    Thread the looper area of the machine following
    the brown color-coded thread guides 4~11.
    Place the thread with the point of the tweezers
    through threading guide 4.
    Place the thread with the point of the tweezers
    through the front slot of threading guide 5.
    Thread the looper eye (A) from front to back.
    Pull about 10cm (4 inches) of thread through the
    looper. Position thread into V cutout (B) on
    threader. Firmly hold thread tail with left hand
    and pull threader lever (C) up into place (D).
    Raise Presser foot
    to release Tension discs. by lowering presser bar lifter
    Note: Use the tweezers provided in the accessory
    case to aid in threading the looper.
    4) Threading the (Blue)
    Overedge Right Needle
    (B on needle clamp) 
    						
    							95
    8 6
    7
    4
    3
    3
    2
    2
    1
    22
    Pass thread from back to the front through the
    thread guide 1.
    While holding thread with finger, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the
    tension discs 3.
    Continue to thread points 4~8.
    Note: Slip thread into the rear slot on the thread guide 5 and the slot of take-up lever cover 6.
    Then slip thread into the right slot on the thread guide 7, and into the right slot on the thread
    guide 8.
    Before threading eye of needle, slip thread behind
    thread guide located on the bottom of the needle
    clamp. Thread the top cover
    thread guide by pulling
    the thread towards the
    left until it slips under
    guide. Then pull thread
    along the right side of
    button as illustrated. 
    						
    							3
    2 1
    9
    7
    8 5
    6
    2
    4
    1
    29
    5) Threading the
    (Orange)
    Chain Stitch Needle
    (D on needle clamp)
    23
    Thread the eye of the right needle 9.
    Note: Use of tweezers in the accessory case willmake needle eye threading easy.
    The position of the thread must be behind the thread
    guide.
    Draw about 10cm(4 inches) of thread through
    needle eye towards the rear of machine.
    Place the thread to the back, under the presser
    foot.
    Thread the top cover
    Thread guide by pulling
    the thread towards the
    left until it slips under
    guide. Then pull thread
    along the right side of
    button as illustrated. Pass thread from back to the front through the
    thread guide 1. Thread the left needle as indicated 1~9.Raise Presser foot
    to release Tension discs. by lowering presser bar lifter 
    						
    							4
    9
    9
    8
    7
    6
    5
    3
    3
    24
    While holding thread with fingers, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the
    tension discs 3.
    Thread the eye of the left needle 9.
    Note: Use of tweezers in the accessory case will make needle eye threading easy.
    The position of the thread must be behind the
    the thread guide.
    Draw about 10cm (4 inches) of thread through
    needle eye to hang free.
    Place the thread to the back, under the presser
    foot. Continue to thread points 4~8.
    Note: Slip thread into the middle slot of the thread guide 5 and into the slot of take-up
    lever cover 6.
    Then continue by slipping thread into the middle slot of the thread guides 7 and 8.
    Before threading eye of needle, slip thread behind
    thread guide located on the bottom of the needle
    clamp.
    Before threading eye of needle, make sure thread
    is located on the bottom of
    in front of thread guide
    the needle clamp.
    Note: For 4 thread overlock left needle: Use needle
    A.
    Note: For chain stitch :Use needle D. 
    						
    							32
    3
    2
    7
    1 9
    8
    5
    6
    1
    43
    2
    (1) Threading the
    Cover Stitch Left Needle
    25
    While holding thread with finger, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the
    tension discs 3. Thread the top cover
    thread guide by pulling
    the thread towards the
    left until it slips under
    guide. Then pull thread
    along the right side of
    button as illustrated. Thread the cover stitch left / chain stitch needle as
    indicated 1~9.
    Pass thread from back to the front through the
    thread guide 1.Raise Presser foot
    to release Tension discs.
    by lowering presser bar lifter
    (Orange) (C on needle clamp)
    6) Threading the Cover Stitch Needles 
    						
    							4
    5
    8
    9 7
    6 3
    2 9
    1
    8
    9
    7
    6
    45
    (2) Threading the Cover Stitch Middle / Chain Stitch
    26
    Needle(Blue) (D on needle clamp)
    Thread the cover stitch middle / chain stitch
    needle as indicated 1~9. Continue to thread points 4~8.
    Note: Slide thread into front slot on thread guide 5 and slot of take-up lever
    cover 6. Then slip thread into left slots
    of thread guides 7 and 8.
    Thread the eye of the left needle 9.
    Note: Use of tweezers in the accessory case will make needle eye threading easy.
    Draw about 10cm (4 inches) of thread through
    needle eye to hang free.
    Place the thread to the back, under the presser
    foot. Before threading eye of needle, make sure thread
    is located on the bottom
    in front of thread guide
    of the needle clamp.
    Raise the Presser foot by lowering presser bar lifter
    to release Tension discs. 
    						
    							9
    8
    6
    7
    3
    4
    5
    3
    2
    2
    1
    27
    While holding thread with fingers, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the
    tension discs 3.
    Continue to thread points 4~8.
    Pass thread from back to the front through the
    thread guide 1.
    Thread the top cover
    thread guide by pulling
    the thread towards the left
    until it slips under guide.
    Then pull thread along the
    right side of button as
    illustrated.
    Before threading eye of needle, make sure thread is
    in front of thread guide located on the bottom of the
    needle clamp for Cover stitch and for Chain stitch. Note: Slip thread into the middle slot of the thread
    guide 5 and into the slot of take-up
    lever cover 6.
    Then continue by slipping thread into the middle slot of the thread guides 7 and 8. 
    						
    							221
    9
    6
    7
    8 5
    43
    2
    1 9
    (3) Threading the
    Cover Stitch Right Needle
    (Green) (E on needle clamp)
    28
    Thread the cover stitch right needle as indicated
    1-9.
    Pass thread from back to the front through the
    thread guide 1.
    Thread the top cover
    thread guide by pulling
    the thread towards the
    left until it slips under
    guide. Then pull thread
    along the right side of
    button as illustrated. Thread the eye of the middle needle 9.
    Note: Use of tweezers in the accessory case will make needle eye threading easy.
    Draw about 10cm (4 inches) of thread through
    needle eye towards the back of the machine.
    Place the thread to the back, under the presser
    foot.
    Raise Presser foot by lowering presser bar lifter to
    release Tension discs. 
    						
    							9
    8
    9 4
    5
    7
    6
    3
    3
    29
    Continue to thread points 4~8.
    Note: Slip thread into the rear slot on thread
    guides 5. Slip the thread into the slot
    of the Take-up Lever Cover 6. Slip the thread
    into the right slots for thread guides 7 and 8.
    Before threading eye of needle, make sure thread is
    in front of thread guide located on the bottom of the
    needle clamp for Cover stitch.
    Thread the eye of the right needle 9.
    Note: Use of tweezers in the accessory case will make needle eye threading easy.
    Draw about 10cm (4 inches) of thread through
    needle eye towards the rear of the machine.
    Place the thread to the back under the presser
    foot. While holding thread with fingers, pass it between
    the tension discs and pull thread down to make
    certain it is properly located in between the
    tension discs 3. 
    						
    All Singer manuals Comments (1)

    Related Manuals for Singer Serger Professional 5 Manual