Singer Serger Professional 5 Manual
Have a look at the manual Singer Serger Professional 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Singer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
4. While holding the thread, firmly pu ll the thread between the tension disks.
5. Turn the handwheel toward you unt il the lower looper extends 5-10mm
(approximately ½”) from the needl e plate edge.
6. Thread the looper area of the mach ine following the red color coded
thread guides 4-10.
7. Place the thread slighty from left and
to the ri ght of threading guide f.
8. Place the thread slightly from the
fr ont and to the back of threading
guide g.
9. Place the thread through h, i and j.
Three-Thread Overlock (narrow) page 10
Three-Thread Overlock (narrow) page 11
10. Thread the looper eye (A) from front to back. Pull about 4 inches of thread.
Position thread into V cutout (B) on thr eader. Firmly hold thread tail with left
hand and pull Threader Lever (C) up into place (D).
NOTE: Make sure the Upper Looper thread is
behind the Lower Looper thread.
Threader Lever
“V” cutout
5. Continue to thread point s 4-8. Slip the thread into the rear slot of the
thread guide g. Go over the take up lever h. Continue by slipping the
thread into the right slot of the thread guides i and j.
8. Before threading the eye of the needle, make sure the thread is
behind
the thread guide located on t he bottom of the needle clamp.
9. Draw about 4 inches of the thr ead through the needle eye towards the back
of the machine.
10. Place the thread to t he back, under the Presser Foot.
Three-Thread Overlock (narrow) page 13
Three-Thread Overlock (wide)
The Three-Thread Overedge (wide) has the same set up as the Three-Thread Over-
edge (narrow) Stitch. The only exceptions are the Right
Overedge Needle is now
unthreaded and removed and the Left
Overedge Needle is threaded. By using the
left needle the stitch becomes wider. The ot her exception is the Auto Tension Dial
is turned to “B”.
Three-Thread Overlock (wide) page 1
Right Overedge Needle Thread
Left Overedge Needle Thread
ATD:
Auto Tension Dial
“B”
Left Cover Stitch
Needle “C” Unthreaded and
Remove Needle
Middle Cover Stitch
Needle “D” Unthreaded and
Remove Needle
Right Cover Stitch
Needle “E” Unthreaded and
Remove Needle
Overedge Left
Needle “A” (Orange) Threaded
Overedge Right
Needle “B” Unthreaded and
Remove Needle
Upper Looper
(Green) Looper Engaged
and Threaded
Lower Looper
(Red) Threaded
Chain Stitch Looper
(Brown) Unthreaded
Upper Knife Engaged
Seam Guide Plate Not Installed, use
Knife Plate Cover
Seam Width Dial “N”
Stitch Length Dial “2”
Presser Foot
Pressure “N”
Differential Feed Dial “N”
Stitch Finger “N”
Spreader Disengaged
Set-up:
Needle:
Three-Thread Overlock (wide) page 2
5. Continue to thread point s 4-8. Slip the thread into the middle slot of the
thread guide g. Go over the take up lever h. Continue by slipping the
thread into the middle slot of the thread guides i and j.
6. Before threading the eye of the needl e, make sure the thread is behind
the thread guide located on the bottom of the needle clamp.
7. Thread the eye of the left needle k.
8. Draw about 4 inches of the thr ead through the needle eye towards the back
of the machine.
9. Place the thread to t he back, under the Presser Foot.
Three-Thread Overlock (wide) page 4