Home > Singer > Sewing Machine > Singer Serger Professional 5 Manual

Singer Serger Professional 5 Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Singer Serger Professional 5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 50 Singer manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							 
       
       
     Three-Thread Flatlock (narrow) page 11  
     10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                     Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                      hand and pull Threader lever (C) up into place (D).  
     
     
     
     
     
       
     
     
     
     
     
     
     
     
     
     
     
     
     
      
     
         
     
     
     
     
     
     
    NOTE: Make sure the Upper Looper thread is 
    behind the Lower Looper thread. 
    Threader Lever 
    “V” cutout   
    						
    							 
      
      
      5. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
          thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
                   thread into the right  slot of the thread guides i and  j.  
     
      8. Before threading the eye of the needl e, make sure the thread is    
                   behind
     the thread guide located on t he bottom of the needle clamp. 
     
     
     
     
     
     
     
     
     
     
     
      
     
      
     
      
      9. Draw about 4 inches of the thr ead through the needle eye towards the back 
          of the machine.  
      
          10. Place the thread to t he back, under the Presser Foot.   
     
     
     
     
     
     
     
     
     
    Three-Thread Flatlock (narrow) page 13  
    						
    							 
      
    Three-Thread Flatlock (wide) 
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
     
          
     
     
     
     
     
     
     
     
     
     
                 
     
     
     
     
     
     
    Three-Thread Flatlock (wide) page 1 
    The Three-Thread Flatlock (wide) has the same set up as the Three-Thread 
    Flatlock (narrow) Stitch.  The only exception is the Right
     Overedge Needle is now 
    unthreaded and removed and the Left
     Overedge Needle is threaded.  By using the 
    left needle, the stitch becomes wider.   
    Right Overedge Needle Thread 
     Left Overedge Needle Thread  
    						
    							 
     
    ATD: 
    Auto Tension Dial  
                “F” 
    Left Cover Stitch  
    Needle “C”  Unthreaded and 
    Remove Needle 
    Middle Cover Stitch  
    Needle “D” Unthreaded and 
    Remove Needle  
    Right Cover Stitch 
    Needle “E” Unthreaded and 
    Remove Needle 
    Overedge Left  
    Needle “A” (Orange)     Threaded 
    Overedge Right  
    Needle “B” Unthreaded and  
    Remove Needle 
    Upper Looper 
    (Green)  Looper Engaged 
    and Threaded 
    Lower Looper 
    (Red)    Threaded 
    Chain Stitch Looper  
    (Brown)   Unthreaded  
    Upper Knife     Engaged 
    Seam Guide Plate Not Installed, use 
    Knife Cover Plate 
    Seam Width Dial          “N” 
    Stitch Length Dial          “2” 
    Presser Foot  
    Pressure          “N” 
    Differential Feed Dial           “N” 
    Stitch Finger          “N” 
    Spreader     Disengage 
    Set at: 
    Needle: 
    Three-Thread Flatlock (wide) page 2  
    						
    							 
     Three-Thread Flatlock (wide) page 3  
     
                Decorative Ladder Effect (wide)                                Decorative Loop Effect (wide) 
                  Fabric Right Sides Together                                    Fabric Wrong Sides Together 
    Right Overedge Needle Thread 
     
    Left Overedge Needle Thread 
     
    Lower Looper Thread 
    Upper Looper Thread  
    						
    							 
       
       
      
     
      5. Continue to thread point s 4-8.  Slip the thread into the middle slot of the  
          thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
                   thread into the middle  slot of the thread guides i and  j.  
     
      6. Before threading the eye of the needl e, make sure the thread is behind
      
                   the thread guide located on the  bottom of the needle clamp. 
     
     
     
     
     
     
     
     
     
     
     
     
     
        
     
     
     
     
      7. Thread the eye of the left needle  k. 
     
     
     
     
     
     
     
      
     
     
     
      
     
     
     
      8. Draw about 4 inches of the thr ead through the needle eye towards the back 
          of the machine.  
      
          9. Place the thread to  the back, under the Presser F oot.  Lower foot and sew.   
     
    Three-Thread Flatlock (wide) page 5   
    						
    All Singer manuals Comments (1)

    Related Manuals for Singer Serger Professional 5 Manual