Siemens Saturn Iie Epabx General Description Manual

I 
SATURN IIE EPABX 
lnstallatlon Test Proccdurcs A30808-X5130-8120-1-8928 
Issue I, May 1986 
J46/P46 
J47/P47 
Figure 4.00 Location of Input Voltage Connectors 011 Basic Bockplnnc  

SATURN IIE EPABX 
A30808-X5130-8120-1-8928 
nstallation Test Procedures 
Issue 1, May 1986 
i 
---I 
I 
:42/?42 
J43/P43 
J44lP44 
Figure 4.0.1 Location cf Input Voltage Connectors on LTU Dackp!ane  

SATURN IIE EPABX A30808-X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
5.01 General. The SATURN IIE EPABX is a Stored-Program- 
Controlled (SPC) system. The system is shipped with two iden- 
tical floppy disks that contain the basic operating and the 
installation-dependent data. The operating program uses the 
installation-dependent data, commonly referred to as the sys- 
tem data base, to complete and process calls as required by 
the customer. This information includes such items...

SATURN IIE EPABX A3080&X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
WARNING 
Hazardous voltages exist within the equipment cabinet. Be e&e&y careful when 
performing testir;g/~roobleshooting procedur- LJ with the equ&ment panel(s) removed. 
Table 5.00 Loading Procedures for Operaling Disk 
;TEP 
PROCEDURE VERIFICATION !F VERIFICATION 
IS NOT OBTA!NED 
1 On the PSU, shown in Figure 5.01, 
place the FAtLURE TRANSFER 
switch in the AUTO position, 
2 Insert a floppy disk into slot...

SATURN IIE EPABX A30808-X5130-0120-1-8928 
Installation Test Procedures lssuc 1, May 1936 
Table 5.00 Loading Procedures for Operating Disk (Continued) 
STEP PROCEDURE VERlFlCATlON IF VERIFlCAT!ON 
IS NOT OBTAINED ’ 
5 If the operating disks that were load- 
ed did not contain a Siemens-. 
prepared data base, refer to SATURN 
EPABX Data Base Preparation prac- 
tice to define the particular system 
data base, and the SATURN EPABX 
Customer Memory Update Proce- 
dures practice to input the installation-...

I’ 
A30808-X5130-(3120-l-8928 
Issue 1, May 1986 
Table 5.02 LED Display Values for Loading Errors 
HEX 
CCDE ERRCR DETECTED 
0 
1 
2 
3 
4 
5 
6 
: 
D 
E 
F 
8 
9 
A 
I3 Start of self test not halted 
Main processor error 
EPROM checksum error 
MEM slot 0 low 64k test error 
8k by 8 static RAM test error 
IRAM memory test error 
ORAM memory test error 
SIB side error 
Global memory error 
Watchdog iimer error 
SIB serial loopback test error 
SIB counter timing test error 
Start boot process (self test...

I 
-- 
SATURN IIE EPABX 
Installation Test Procedures A30808-X5130-6120-1-8928 
Issue 1, May 1986 
LATCH 
OPEN 
LATCH 
CLoSED  
/ 
/ 
? 
25 
0 
WRITE 
PROTECT 
NOTCH 
FLOPPY 
/ DiSi’c 
Figure 5.02 Floppy Dish Loading Proceduics  

I 
- 
SATURN IIE EPABX 
Installation Test Procedures A30800-X5130-6120-l-8928 
Issue 1, May 1986 
LED 
LED 
(Red) 
ST3 
LED 
ACTW 
r 
LED 
Connector 
Service 
Terminal 
‘witch 
Figure 5.03 CIOP Printed Circuit Coard 
5-6 (6 pages)  

SATURN IIE EPABX 
A30808-X5130-BlZO-l-8920 
Installation Test Procedures Issue 1. May 1986 
6.01 General. After satisfactorily loading the cperating disk 
and inputting CMU data to system memory via a service ter- 
minal, the operational capability of the system must be veri- 
fied after the necessary MDF cross-connections are 
performed. The SATURN IIE System software contains a 
group of system and apparatus (ancillary equipment) diag- 
nostic test routines which are accessed via the maintenance...

I 
.- 
SATURN IIE EPABX A30808-X5130-B120-l-B928 
lnstallatlon Test Procedures Issue 1, May 1986 
,-Syslein MDF Cable J13 
Cross-connect .to SLMA circuit designated 
for the maintenance telephone. 
1 PXFER (No&h Ooen1 
J , I 
PXFER (Normally Closed) Cross-connect to failure transfer 
relay(s) subsystem (customer- 
provided). 
\$$! > :tG TIP (Major-NC) 
> RING (Major Common) 
0 14 
D > FUBL TIP (Major-NO) Dry contact closures 
for remoie miner and 
major alarm indica- 
tions (customer- 
provided). 
Syslem...