Siemens Saturn Iie Epabx General Description Manual

SATURN IIE EPABX A30808-X5130-BllO-l-8928 Installation Procedures Issue 1. May 1986 
Slot 
.’ 
Number 
1 Cable 
Connector 
for T & R 
Leads 
Cable 
pezt; 
or T&R Leads 
for SU16 
slot Number 
Cable 
Connector 
for T 6 R 
Leads 
Cable 
Connector 
for 
E a M or T&R Leads 
for SW3 Channel Channel 
Group 0 Group 
1 
0245 02 Basic Shelf Assembly (Front View) 
Channel Channel Channel Channel Channel 
Group 2 Group 3 Group 4 Group 5 Group 6 
0246 02 0246 02 02 
I I 
I I 
J32 J34 
/ ; 
I J33 J36 
Channel Channel...

A30808-X5130-BllO-1-0928 
issue 1, May 1986 
ASSIGNMENT OF PENS 
Shelf (basic = 0, LTU = 1, 2, 3) 
&. Channel Group (O-7; see above ) 
Card Slot (O-6: see below for SLA16) 
Circuit (O-7; see below for StA16) I 
For SLA16 Boards: 
Circuits O-7: Use slot number (Y) as shown above. 
Circuits 8-15: Use slot number +l r/+1) 
EXAMPLE: SLA16 assigned to LTU Shelf 2, Channel Group 3, Slot 0 
PENS of first 8 circuits: 2300 through 2307 
T/R leads of circuits are located on connector J32 
PENS of second 8...

Siemens Practices 
Installation Series : 
A30808-X5130-8120-1-8928 1 
Issue 1, May 1986 
’ 1 
! 
Issued by Office Systems Group 
5500 Broken Sound Boulevard N.W., Boca Raton, Florida 33431 
--___________- 
Siemcns Information Systems, Inc. (305) 994-8100 
l Telex: 515052 
----- - ..- ----- 
Printed in U.S.A.  

SATURN IIE EPABX A30808X5130-8120-1-8328 
Installation Test Procedures Issue 1, May 1906 
SECTION PAGE 
l.CO INTRDCUCTlON ............ 
; ............. .1-l 
Purpose .................................. l-l 
scope .................................... 1-l 
Siemens SATURN IIE Practices ................. l-l 
Siemens Customer Support Services. ........... l-l 
2.00 PREP/%KGXIY ACTIVITY ................... 2-1 
Cener21. ................................. 2-1 
Test Equipment Required. ................... 2-l...

SATURN IIE EPABX 
installation Test Procedures A30808-X5130-0120-l-0928 
Issue 1, May 1986 . 
1.01 Purpose. The equipment comprising the SATURN IiE 
(SATURN Ii-Expanded) System is compleYely tested at the fac- 
tory prior to shipment. The inspections and tests covered in 
this practice verify that the EPABX equipment has been 
properly installed; ensure that no damage wasIncurred dur- 
ing transit; and confirm that the sysiem is completely opera- 
tional. Table 1.00 defines the mnemonics usedthroughout...

SATURN IIE EPABX 
Installation Test Procedures 
. 
Table 1.00 Mnemonics Used in This Practice (Continued) 
[\fiNEMDNIC * DEFINITION 
RAUP Remote Access Unit/Ports 
RGEN Ring Generator 
S-416 Subscriber Line Module Analog - 16 lines 
SLMA Subscriber Line Module Analog 
SLMA-S Subscriber Line Module Analog - Station 
SLMD Subscriber Line Module Digital 
SMXTG Signal Multiplexer/Tone Generator 
SPC Stored-Program-Controlled 
SPG Single Point Ground 
TMBA-2 Two-Wire E&M Trunk 
TMBA-4 Four-Wire E&M Trunk...

SATURN IIE EPABX A30808-X5130-B120-l-8928 
Installation Test Procedures Issue 1, May 1986 
2.01 General. This section describes the test equipment re- 
quired to perform the installation test procedures, handling 
precautions for Printed Circuit Boards (PCBs) with Metal Ox- 
ide Semiconductor (MOS) integrated circuits, guidelines for 
removal and replacement of PCBs and powei supplies, and 
initial visual inspection procedures. 
2.02 Test Equipment Required. The following test equip- 
ment is required to...

- 
Table 2.00 PC3 and Power Supply Remcval Guidelines 
I’AODIJLE OR SERVEC” SPECIAL 
UNIT STATE INSTRUCTKWIS 
CIOP NA 
CONF . NA 
DTMF 00s 
FDDO, FDDl NA 
LTUC f 
NA 
LTUPS 
l NA 
MCA 
MEM3 kz 
MEM4 NA 
MSM 
l NA 
MSM Baitery l NA 
PIMD 00s 
PSC NA 
PSU NA 
RAUP 
NA 
SLAl6 00s 
SLMA-0 00s 
SLMA-S 003 
SLMD 00s 
SMXTG 
ES  TMBA-2 
TMBA-4 
00s 
TMBM 
00s 
TMIE 
00s 
-48PS.l NA 
-48PSt f 
NA 
* Optional depending upon customer/system requirements. 
NA = Not Applicable; 00s = Out-of-Service Notes 1 and 2...

I 
.- 
A30808-X5130-B120-l-8928 
Issue 1, May 1986  SATURN IIE EPABX 
Installation Test Procedures 
Table 2.01 Visual Inspection 
STEP 
VISUAL INSPECTION REFERENCE 
1 Check that the cabinet ac power cord is not connected to an 
electrical outlet. 
2 Check that the -48Vdc power supply is strapped for SATURN IIE EPABX Installation 
11OVac or 22OVac. Procedures Practice (Section 4.00) 
3 
Check that all circuit breakers on the Power System Unit SATURN IIE EPABX Installation 
(PSU) are in the OFF position...

w3 w13 
- 
I I 
SATURN IIE EPABX 
,xtallation Test Procedures A30808-X5130-B120-l-5928 
Issue 1, May 1986 
Figure 2.00 
Signal Cable Distribution for the SATURN IIE System (Basic Cabinet)