Sharp Mx M453n Owners Manual

7-64
SYSTEM SETTINGS
Contents
Preview Setting
Configure settings for the preview screen that can be 
used for fax / image send and document filing.
Default Preview
Set the selection state of the [Preview] key in each of the 
screens below.
Copy
Image Send
 Scan Send
 Internet Fax Send
 Fax Send
 Data Entry
 USB Memory Scan
 Address Book
Document Filing
 Scan to HDD
Default Preview Display
Set the display zoom ratio of the preview screen for 
copy, fax / image send, and document filing.
Received Data...

7-65
SYSTEM SETTINGS
Contents
Device Control
These settings control devices installed on the machine. Touch the [Device Control] key to configure the settings.
Other Settings
Original Feeding Mode
The following original feeding modes can be set to 
operate by default in copy, Scan to HDD, and image 
send modes. When a mode is frequently used, this 
saves you from having to select the mode in the special 
modes each time you need to use it.
 Mixed Size Original (Same Width (Copy mode 
only)/Different...

7-66
SYSTEM SETTINGS
Contents
Auto Switching of Finisher Trays
(When a finisher (large stacker) is installed.)
If the number of sheets on the upper finisher tray 
reaches the sheet limit, output will automatically switch 
to the lower tray.
Optimization of a Hard Disk
This function optimizes the hard drive of the machine by 
defragmenting data. If a job is in progress, a message 
will appear and optimization will not begin until the job is 
finished. During optimization, the following operations 
are not...

7-67
SYSTEM SETTINGS
Contents
Original Size Detector Setting
One of the 8 groups of standard original sizes shown below can be selected for detection by the original size detection 
function.
Cancel Detection at Document Glass
Original size detection on the document glass can be disabled. When this is done, all originals placed on the document 
glass are treated as special size originals.
Selections
Detectable original sizes
Document glassDocument feeder tray (automatic 
document feeder)
AB-1A3, A4, A4R,...

7-68
SYSTEM SETTINGS
Contents
Disabling of Devices
Use these settings when a peripheral device on the machine has failed or when you wish to temporarily disable a device.
Disabling of Document Feeder
Use this setting to prohibit the use of the automatic 
document feeder, such as when the feeder malfunctions. 
(When the setting is enabled, scanning is still possible 
using the document glass.)
Disabling of Duplex
This is used to disable two-sided printing, such as when 
the duplex module malfunctions....

7-69
SYSTEM SETTINGS
Contents
Copy Function Settings
The following settings are related to copying. Touch the [Copy Function Settings] key to configure the settings.
Default settings selected with these settings apply to all functions of the machine (not just the copy function).
Initial Status Settings
The copier settings are reset when the [POWER] key ( ) is turned on, when the [CLEAR ALL] key ( ) is pressed, or 
when the auto clear interval has elapsed. These settings are used to change the default...

7-70
SYSTEM SETTINGS
Contents
Other Settings
Copy Exposure Adjustment
This is used to adjust the exposure level when [Auto] is 
used for the copy exposure.
Select separate settings for the document glass and for 
the automatic document feeder.
Rotation Copy Setting
When the original and paper are placed in different 
orientations, this function automatically rotates the image 
90 degrees to enable correct copying on the paper.
Add or Change Extra Preset Ratios
Two enlargement preset ratios (101% to 400%)...

7-71
SYSTEM SETTINGS
Contents
Disabling Deletion of Job Programs
This is used to prohibit the deletion and changing of copy 
settings stored in job programs.
Disabling of Bypass-Tray in 
Duplex Copy
This is used to prohibit the use of the bypass tray when 
making two-sided copies.
The bypass tray is often used to feed label sheets, 
transparency film, and other special media for which 
two-sided copying is prohibited. If a sheet of one of these 
special media enters the reversing unit, a misfeed or...

7-72
SYSTEM SETTINGS
Contents
Network Settings
Network settings are described below. Touch the [Network Settings] key to configure the settings.
IPv4 Settings
When using the machine on a TCP/IP (IPv4) network, use 
this setting to configure the IP address of the machine.
The settings are shown below.
IP Address
Enter the IP address of the machine.
IP Subnet Mask
Entry the IP Subnet Mask.
IP Gateway
Enter the IP Gateway address.
DHCP
Use this setting to have the IP address obtained 
automatically using...

7-73
SYSTEM SETTINGS
Contents
Printer Settings
Settings related to the printer function can be configured. Touch the [Printer Settings] key to configure the settings.
Default Settings
Printer condition settings are described below.
Prohibit Notice Page Printing
This setting is used to disable printing of notice pages.
Prohibit Test Page Printing
This setting is used to disable printing of test pages. 
When this setting is enabled, Printer Test Page in the 
system settings cannot be used to print test...