Sharp Mx M453n Owners Manual

7-104
SYSTEM SETTINGS
Contents
* This function is not available in some countries and regions.
‹Transaction Report Print Select Setting
7-106
 Single SendingPrint Out Error Report Only
 BroadcastingPrint Out All Report
 ReceivingNo Printed Report
 Confidential ReceptionPrint Out Notice Page
‹Activity Report Print Select Setting
7-106 Auto Print at Memory FullDisabled
 Print Daily at Designated TimeDisabled
‹ECMEnabled7-106
‹Distinctive Ring Detection*Off7-106
‹PBX Setting*Disabled7-106
XFax Send...

7-105
SYSTEM SETTINGS
Contents
Image Send Settings
Settings related to the image send function (scan, Internet fax, etc.) can be configured. Touch the [Image Send Settings] 
key to configure the settings.
Fax Settings
The fax settings can be enabled or disabled to suit the 
needs of your workplace.
Dial Mode Setting
This setting can only be activated in Canada and 
Taiwan.
Select the appropriate setting for your telephone line 
type.
Dial Mode Setting
Select the line type from the list.
Auto Select...

7-106
SYSTEM SETTINGS
Contents
Original Print on Transaction 
Report
When a transaction report is printed for a memory 
transmission, this is used to print part of the first page of 
the transmitted original on the transaction report. Select 
one of the settings below.
 Print Out All Report
 Print Out Error Report Only
 No Printed Report
This setting will not be effective if Transaction Report 
Print Select Setting below is set to No Printed Report.
Transaction Report Print Select 
Setting
This is used...

7-107
SYSTEM SETTINGS
Contents
Settings for fax transmission can be configured.
Auto Reduction Sending Setting
This setting is used to have the size of transmitted faxes 
automatically reduced to match the size of the paper in 
the receiving machine.
If the setting is disabled, faxes are sent at full size. 
Because the size is not adjusted to match the size of the 
printing paper, part of the received fax may be cut off.
Rotation Sending Setting
When transmitting an image that is one of the following...

7-108
SYSTEM SETTINGS
Contents
Recall in Case of Line Busy
This program is used to set the number of recall 
attempts and the interval between recall attempts when 
a transmission is not successful due to the line being 
busy or other reason.
Number of Times to Recall When Line is Busy
This setting specifies whether or not recalling is 
performed when the line is busy. When recalling is 
performed, you can set the number of recall attempts.
Interval to Wait Between Recall Attempts (min.) 
When Line is...

7-109
SYSTEM SETTINGS
Contents
Settings for fax reception can be configured.
Number of Calls in Auto Reception
This setting is used to select the number of rings on 
which the machine automatically receives a call and 
begins fax reception in auto reception mode. 
The Number of Calls in Auto Reception that can be set 
in each country are shown in the following table.
Country Differentiation Table
Switching from Manual to 
Automatic Reception
This setting can only be activated in France.
When a fax is...

7-110
SYSTEM SETTINGS
Contents
Letter Size RX Reduce Print
This program is not available in Canada and Philippines.
When a letter-R (8-1/2 x 11R) size fax is received, this 
setting reduces the fax to A4R size.
Receiving Date & Time Print
Enable this setting to have the date and time of 
reception printed.
Select [Inside the Received Image] or [Outside the 
Received Image] for the position where the date and 
time is printed.
When [Inside the Received Image] is selected, the date 
and time of reception...

7-111
SYSTEM SETTINGS
Contents
The following settings are for regular polling memory 
using the Public Box.
Set Fax Polling Security
When the memory polling function is used, this setting 
determines whether any machine will be allowed to poll 
your machine, or only machines that have been stored in 
your machine.
Add New
When the Polling Security Setting is enabled, use this 
setting to store (or delete) the fax numbers of the 
machines that are allowed to poll your machine. The 
stored fax numbers are...

8-1
This chapter provides solutions to possible problems in a question and answer format. Locate the question that relates 
to your problem and use the answer to help correct the situation. If you are unable to solve a problem using this manual, 
please contact your dealer or nearest authorised service representative.
System settings
Descriptions of system settings similar to the following example appear in this manual.
Example:
 ➞ System Settings (Administrator) > Copy Function Settings > Other Settings...

8-2
TROUBLESHOOTING
Contents
This section explains what to do when a paper misfeed occurs in the machine.
REMOVING MISFEEDS
When a paper misfeed occurs, the message A misfeed has occurred. will appear in the touch panel and printing and 
scanning will stop. In this event, touch the [Information] key in the touch panel. When the key is touched, instructions for 
removing the misfeed will appear. Follow the instructions. When the misfeed is cleared, the message will automatically 
clear.
The approximate...