Sharp Mx 4100n Owners Manual

8-8
TROUBLESHOOTING
Contents
Follow the steps below to remove a staple jam.
☞FINISHER
☞FINISHER (LARGE STACKER) (page 8-10)
☞SADDLE STITCH FINISHER (page 8-12)
FINISHER
REMOVING STAPLE JAMS
1
Open the cover.
2
While pressing the lever over to the left, 
slide the finisher to the left until it stops.
Gently slide the finisher until it stops.
3
Lower the staple case release lever and 
remove the staple case.
Pull the staple case out to the right.
4
Raise the lever at the front end of the 
staple case and...

8-9
TROUBLESHOOTING
Contents
5
Lower the lever at the front end of the 
staple case.
6
Replace the staple case.
Push the staple case in until it clicks into place.
7
Slide the finisher back to the right.
Gently slide the finisher back to the right until it locks into its 
original position.
8
Close the cover. 

8-10
TROUBLESHOOTING
Contents
FINISHER (LARGE STACKER)
1
Open the front cover.
2
Squeeze the green parts of the staple 
case and pull the case up and then out.
3
Lower the lever at the front end of the 
staple case and remove the jammed 
staple.
Remove the leading staple if it is bent. If bent staples remain, a 
staple jam will occur again.
Take care that a bent staple does not hurt you.
4
Return the lever to its original position. 

8-11
TROUBLESHOOTING
Contents
5
Push the staple case firmly back in.
Push the staple case in until it clicks into place.
6
Close the front cover.
Make a test print or copy using the saddle stitch function to verify that stapling takes place correctly. 

8-12
TROUBLESHOOTING
Contents
SADDLE STITCH FINISHER
Finisher unit
1
Open the front cover.
2
While pulling the lever, slide the saddle 
stitch finisher to the left until it stops.
3
Lower the staple case release lever and 
remove the staple case.
Pull the staple case out to the right.
4
Raise the lever at the front end of the 
staple case and remove the jammed 
staple.
Remove the leading staple if it is bent. If bent staples remain, a 
staple jam will occur again.
Take care that a bent staple does not...

8-13
TROUBLESHOOTING
Contents
6
Replace the staple case.
Push the staple case in until it clicks into place.
7
Push the saddle stitch finisher back and 
latch it to the machine.
8
Close the front cover.
Make a test print or copy in staple sort mode to verify that stapling takes place correctly. 

8-14
TROUBLESHOOTING
Contents Saddle stitch unit
Before starting this procedure, remove all output from the output tray of the saddle stitch finisher. Do not replace 
removed output in the output tray.
1
Open the side cover.
2
Remove the staple cartridge from the 
staple unit.
3
Lock the staple unit.
Push the staple unit up until you hear a click.
4
Press (A) down and pull up knob (B).
5
Remove the jammed staples.
Take care that a bent staple does not hurt you.
(A)
(B) 

8-15
TROUBLESHOOTING
Contents
6
Push down knob (B).
7
Load new staple cartridges.
Remove the cover from each staple cartridge and then install 
the cartridge.
8
Close the side cover.
Make a test print or copy using the saddle stitch function to verify that stapling takes place correctly.
(B) 

8-16
TROUBLESHOOTING
Contents
PROBLEMS RELATED TO COPYING OPERATION
COPYING
PROBLEMS RELATED TO COPYING OPERATION
 Copying does not take place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16
 Auto selection of the color mode does not take place. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16
 Image rotation does not take place.  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

8-17
TROUBLESHOOTING
Contents
Image rotation does 
not take place.Did you select the paper size or copy 
ratio manually?Copy using automatic paper selection and automatic 
ratio selection.
Are you copying using settings that do 
not allow rotate copying?Rotate copying can generally be combined with other 
special modes, however, some combinations are not 
possible. If a prohibited combination is selected, a 
message will appear in the touch panel.
Is Rotation Copy Setting disabled in 
the system settings...