Sanyo Projector Plc Xc56 User Manual

1
ENGLISH

 

How to use the setting page
Radio button setting
Select an item by selecting a radio button.
Check box setting
Select items by ticking on check boxes. 



Chapter 3 Basic Setting and Operation

Initial setting
After installing the projector, perform the following basic initial setting.
Click Initial Setting on the main menu to display the initial setting page.
Item Description
Language ..............  
Switches display language on the setting page. English or Japanese.
Model	name  .......  
Indicates the model name of the projector
Network PIN code  ...... 
Sets the Network PIN code to login the setting page (+p.23) PJLink...


ENGLISH

 

Initial setting
Network PIN code setting
This  is  to  set  the  Network  PIN  code  to  restrict 
t h e  a cce s s  f ro m  a n  u n a u t h o r i ze d  p e r s o n 
through the network. 
Enter  a  4 - digit  number  as  the  Net work  PIN 
code onto the text box and click Set button. 
  
The  projector  begins  restar ting  and  it  takes 
about  10  seconds.  Close  (Quit)  the  web  browser  and  access  to  the  login  page  again  in  10 
seconds. This is to perform the...



Chapter 3 Basic Setting and Operation

Network configuration
Click Network on the main menu. The following setting page is displayed. 
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) 
and projector name are set up on this menu.
The  IP  address  and  Subnet  Mask  have  been  configured  already  in  chapter  "Installation". 
If  you  want  to  change  them  or  configure  default  gateway  or  DNS,  perform  them  in  this 
page.  If  you  change  them,  the...

5
ENGLISH

 

E-mail setting
This  projector  has  an  E-mail  function  which  can  send  an  alert  message 
to  users  or  an  administrator  if  it  detects  an  abnormality  on  the  projector 
or  run  out  of  the  life  span  of  the  lamp.  Click E-mail  Setting  on  the  main 
menu and follow the below steps.
E-mail setting
Item .................................Description
SMTP	server*1........................ Sets server name or IP address of the SMTP serverAdministrator	address...



Chapter 3 Basic Setting and Operation

2  Registering and deleting E-mail addresses
Click  "Add  address"  and  t yp e  the  e -mail 
address  onto  the  te x t  box  and  click Set 
button.  To  check  the  registered  addresses, 
click  Che c k / D e l e te  sub  menu  t ab.  T he 
addresses  are  listed  as  the  figure  on  the 
right.
✐ Up to 10 E-mail addresses can be registered.
To  delete  the  registered  addresses,  check  the 
address  you  want  to  delete  and  click...


ENGLISH

 

● When PJ needs service:
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201	Projector	Name:	Proj05
It	sends	you	following	message.
* 	 Maintenance	requirement	from	Projector	is	detected.
	
Check	up	LED	status	of	projector	and	consult	with	the	dealer.
MCI	 3.3V	 OKMAIN	 ALL	 NG
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the regis-
tered  E-mail  address  according  to...



Chapter 3 Basic Setting and Operation

● When PJ lamp replacement time is reached:
✐  Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached".
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201...


ENGLISH

 

✐		The SNMP agent provided with this projector is based upon MIB-2 defined by RFC1213. For private MIB information, refer to file "Mibinfo/XUPjNet.mib" in the CD-ROM.
SNMP setting
This  projector  provides  a  SNMP  (Simple  Network  Management  Protocol) 
agent  function.  The  SNMP  consists  of  a  manager  and  agents.  The  group 
w h i c h  c o m m u n i c a t e s  i n f o r m a t i o n  e a c h  o t h e r  w i t h  S N M P  i s  c a l l e d 
"Community"....

0

Chapter 3 Basic Setting and Operation
Check and delete the trap address
Ch e ck in g  th e  re gis tere d  tr ap  a d dress  an d 
deleting the address.
To  delete  the  address,  tick  check  box  in  front 
of the IP address and click Delete button.
✐ Up to 10 trap addresses can be registered.
Trap	check/delete
Trap	option
Trap option setting
Tick check boxes in front of the condition item 
to send the trap. 
✐  Click Set button if you tick or un-tick the check box on a page.
✐		"When PJ...