Sanyo Projector Plc Xc56 User Manual

							
1
ENGLISH

 

How to use the setting page
Radio button setting
Select an item by selecting a radio button.
Check box setting
Select items by ticking on check boxes. 
						

							


Chapter 3 Basic Setting and Operation

Initial setting
After installing the projector, perform the following basic initial setting.
Click Initial Setting on the main menu to display the initial setting page.
Item Description
Language ..............  
Switches display language on the setting page. English or Japanese.
Model	name  .......  
Indicates the model name of the projector
Network PIN code  ...... 
Sets the Network PIN code to login the setting page (+p.23) PJLink  .......................  
Switches PJLink password authentication on or off (+p.23)Password ...............  
Password for PJLink function (+p.23) 
						

							

ENGLISH

 

Initial setting
Network PIN code setting
This  is  to  set  the  Network  PIN  code  to  restrict 
t h e  a cce s s  f ro m  a n  u n a u t h o r i ze d  p e r s o n 
through the network. 
Enter  a  4 - digit  number  as  the  Net work  PIN 
code onto the text box and click Set button. 
  
The  projector  begins  restar ting  and  it  takes 
about  10  seconds.  Close  (Quit)  the  web  browser  and  access  to  the  login  page  again  in  10 
seconds. This is to perform the login authentication firmly.
The default Network PIN code [0000] means no Network PIN code is set.  
✐		When you connect the projector to the network, it is recommended to set a new Network PIN code. Only a four-digit number is valid for the Network PIN code.
PJLink and password setting
This  is  to  set  the  PJLink  password  authentica-
tion  on  or  off.  If  set  "On"  with  the  PJLink  pull-
down  menu,  the  password  must  be  required. 
Enter  a password*  onto  the  te x t  b ox  and 
click Set button. 
✐		  
1 to 32 alphanumeric characters can be used for the password.
What's PJLink?
The projectors equipped with PJLink function can be used together on the same network, 
regardless  of  model  or  brand,  for  centralized  control  and  monitoring.  This  standard  was 
established  by  the  Japan  Business  Machine  and  Information  System  Industries  Association 
(JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/.
PJLink Notice
The  projector  is  compliant  with  PJLink  Standard  Class  1  of  JBMIA,  and  it  supports  all  com-
mands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1.
Projector InputPJLink InputParameterComputer 2RGB (PC analog)RGB 111RGB (PC digital)DIGITAL 131RGB (AV HDCP)DIGITAL 232Computer 1RGBRGB 212ComponentRGB 313RGB (Scart)RGB 414VideoVideoVIDEO 222S-videoVIDEO 323 
						

							


Chapter 3 Basic Setting and Operation

Network configuration
Click Network on the main menu. The following setting page is displayed. 
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server) 
and projector name are set up on this menu.
The  IP  address  and  Subnet  Mask  have  been  configured  already  in  chapter  "Installation". 
If  you  want  to  change  them  or  configure  default  gateway  or  DNS,  perform  them  in  this 
page.  If  you  change  them,  the  projector  begins  restarting  and  it  takes  about  10  seconds. 
Close (Quit) the web browser and access to the login page again in 10 seconds. 
*1 Set [0.0.0.0] if the network does not provide the gateway (router).*2 Set [0.0.0.0] if you do not use the function E-Mail alert.
*3  If you use the DNS server, register the host name registered to the DNS server as a projector 
name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector.* All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.
*  If you make incorrect settings, you cannot find out the new network settings. Be careful to set up 
them correctly, otherwise you cannot connect to the projector. It is recommended to make a note of them.
Item  Description
LAN	mode  ............
Displays the selected LAN modeDHCP .........................Sets DHCP configuration (ON/OFF).
IP	address  .............Sets IP address of the projector
Subnet	mask  .......Sets Subnet mask. Normally sets 255.255.255.0Default gateway*1  .....Sets IP address of the default gateway (Router)DNS*2 .......................   Sets IP address of the DNS server. Must be set when using the e-mail functionProjector	name*3 .  
Sets name of the projector. (64 characters maximum)
✐   You must use the number specified by your administrator. The address must be entered as a group with four numbers split by a dot like [192.168.001.101]. 
						

							
5
ENGLISH

 

E-mail setting
This  projector  has  an  E-mail  function  which  can  send  an  alert  message 
to  users  or  an  administrator  if  it  detects  an  abnormality  on  the  projector 
or  run  out  of  the  life  span  of  the  lamp.  Click E-mail  Setting  on  the  main 
menu and follow the below steps.
E-mail setting
Item .................................Description
SMTP	server*1........................ Sets server name or IP address of the SMTP serverAdministrator	address  ....Sets e-mail address of administrator
Add	address  ...........................  
Sets e-mail address of the user to send mail when  the projector has an 
abnormality.
1 Setting SMTP server and administrator address
Set  the  server  name  or  IP  address  of  the  SMTP  server*1 and  administrator  address.  The 
administrator  address  is  set  to  "Reply-To"  address  of  the  message  sent  from  the  projec-
tor.*1  The SMTP server is a server for sending E-Mail. Please contact your network administrator to have this SMTP server address.
✐  If the projector sends an alert message due to the abnormality on the projector but the SMTP server is down in some other reason, the message will not be sent. In this case, the message "Unable to connect to server." will be displayed on the setting page. To clear this message, set up SMTP server address again.
✐   
To use the E-Mail function, it must be set the DNS address on the Network setting page correctly.✐   You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your net-work environment. 
✐   
The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter the administrator address into "Add address" text box. 
						

							


Chapter 3 Basic Setting and Operation

2  Registering and deleting E-mail addresses
Click  "Add  address"  and  t yp e  the  e -mail 
address  onto  the  te x t  box  and  click Set 
button.  To  check  the  registered  addresses, 
click  Che c k / D e l e te  sub  menu  t ab.  T he 
addresses  are  listed  as  the  figure  on  the 
right.
✐ Up to 10 E-mail addresses can be registered.
To  delete  the  registered  addresses,  check  the 
address  you  want  to  delete  and  click Delete 
button.
3  Option selection for sending alert mail
Click Option sub menu tab. Check the con-
dition  items  under  which  alert  mail  will  be 
sent and click Set button.
 
Please  refer  to  item  "E xamples  :Type  and 
contents of alert mail" described on the next 
page.
Check / Delete
Option
✐		"When PJ lamp is off " signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control.
✐	Up to 99,999 hours can be set for use time. 
						

							

ENGLISH

 

● When PJ needs service:
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201	Projector	Name:	Proj05
It	sends	you	following	message.
* 	 Maintenance	requirement	from	Projector	is	detected.
	
Check	up	LED	status	of	projector	and	consult	with	the	dealer.
MCI	 3.3V	 OKMAIN	 ALL	 NG
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the regis-
tered  E-mail  address  according  to  your  selected  condition.  Administrator  or  user  can  take 
an  efficient  action  quickly  by  receiving  this  message.  This  is  very  useful  to  maintain  and 
service the projector.
The following are examples of received messages.
● When internal PJ temperature is too high:
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201	Projector	Name:	Proj05
It	sends	you	following	message.
*	 The	Projector	lamp	is	turned	off,	because	internal	
p rojector	 temperature	is	too	high.		
Wait	for	the	completion	of	the	cooling	process	and	make	sure	the	projector	has	been	
turned	into	Standby.	 Then	turn	the	
projector 	on	again.		
If	the	Indicator	continues	flashing,	check	the	air	filter	for	dust	accumulation.
✐    The projector lamp was turned off, because the projector power circuit failed.Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information.
Error information
E-mail setting 
						

							


Chapter 3 Basic Setting and Operation

● When PJ lamp replacement time is reached:
✐  Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users in every power-on of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached".
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201	Projector	Name:	Proj05
It	sends	you	following	message.
*The	projector	lamp	has	reached	replacement	time.
Lamp	ON	2000	h
● When lamp corres. value reaches preselect use time:
TITLE:	Message	from	projector
Projector	Model	Name:	model name
TCP/IP:	192.168.1.201	Projector	Name:	Proj05
It	sends	you	following	message.
*The	accumulated	lamp	use	time	has	reached	2000	hours.	 
						

							

ENGLISH

 

✐		The SNMP agent provided with this projector is based upon MIB-2 defined by RFC1213. For private MIB information, refer to file "Mibinfo/XUPjNet.mib" in the CD-ROM.
SNMP setting
This  projector  provides  a  SNMP  (Simple  Network  Management  Protocol) 
agent  function.  The  SNMP  consists  of  a  manager  and  agents.  The  group 
w h i c h  c o m m u n i c a t e s  i n f o r m a t i o n  e a c h  o t h e r  w i t h  S N M P  i s  c a l l e d 
"Community".  There  are  two  access  modes  in  a  community,  Refer  (read  only)  and  Set  (read- 
write). This projector allows to use Refer (read only) only. The SNMP message informs the pro-
jector  status  called  "Trap"  to  an  administrator.  Click SNMP  Setting  on  the  main  menu  and 
set up each item.
Item ........................................Description
Contact  ...............................................  
Enter user name of the projector etc. (optional)Place .....................................................Enter place of the projector (optional)Community name(refer)  .......  
Enter community name (read only). Default name is "public". 
PJ	information
SNMP setting
Item
 ........................................Description
Community name  ......................  
Enter community name to send "Trap". Default name is "public".Add address  ....................................  
Enter IP address of the SNMP manager computer to receive "Trap".
Trap 
						

							
0

Chapter 3 Basic Setting and Operation
Check and delete the trap address
Ch e ck in g  th e  re gis tere d  tr ap  a d dress  an d 
deleting the address.
To  delete  the  address,  tick  check  box  in  front 
of the IP address and click Delete button.
✐ Up to 10 trap addresses can be registered.
Trap	check/delete
Trap	option
Trap option setting
Tick check boxes in front of the condition item 
to send the trap. 
✐  Click Set button if you tick or un-tick the check box on a page.
✐		"When PJ lamp is off " signifies the lamp goes out without user operation. "When PJ is turned into Standby  in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control.
✐	Up to 99,999 hours can be set for the time setting.