Sanyo Projector Plc Xc56 User Manual

							
1
ENGLISH

 

Setting up the projector
Item Description
Key	lock  ..................  
Sets the prohibition of controls either 
Projector or Remote control. (OFF, Projector keys, Remote control)
Lamp	Corres.
Value(h)  ..................  
Displays the lamp use time (Corresponding value) . Reset the time after lamp replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset.
Filter	
counter(h)  ............  
Displays the filter counter. Reset the time after filter cartridge replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. 
Scrolls	
remaining  .............  
Displays  the scrolls remaining of the filter. Reset the scroll counter after filter car-tridge replacement. Click "Reset", a confirmation display appears, and then click "OK", the time will be reset. 
Filter	control  .......  
Scroll the filter. Click "Roll-up", a confirmation display appears, and then click "OK", the 
filter will be scrolled. 
Filter	warning.....  
Sets the time to indicate the filter warning message on the screen. (OFF, 400H, 700H, 1000H) Factory default  ..........  
Sets all of the projector control items to the factory default setting except the fol-lowing items.
   
Lamp Corres. Value, PJ time, Network PIN code, Network setting
   
*  
This function is not effective for the settings of Network address settings, e-mail 
settings, etc.
No	show  .................  
Sets the black out image temporarily. (ON, OFF)
Freeze ......................  
Sets the image to freeze mode.  (ON, OFF)
Closed	caption  ..  
Sets the closed caption function. 
 Closed caption ...  
Sets the closed caption mode. (OFF, CC1, CC2, CC3, CC4)
  Color  .....................  
Sets the color of the contents. (Color, White) 
Setting 3 
						

							


Chapter 4 Controlling the Projector

Information
This  page  is  to  display  the  basic  information  of  the  projector  status.  Click 
Information on the main menu.
Items Description
Input  Displays selected input and source.System  Displays selected signal system.Signal  Input signal status (Yes, No)Screen  Displays screen mode.Lamp	status   Displays lamp status with an animation. Refer to the table as shown in the next page.Security Displays the security (PIN code lock) status (Yes, No)PJ	time(h)  
Displays the accumulated use time of the projector.Lamp	Corres.	 Value(h)   Displays the use time (Corresponding value) of the lamp.
Filter	time(h)  
Displays the accumulated use time of the filter.Filter condition    Displays filter status with an animation. Refer to the table as shown in the next page.
Click this button to update the information. 
						

							

ENGLISH

 

Indication of the lamp status
Icon display/backgroundStatus
 White-Yellow/BlueLamp on (Normal)
White-Yellow/RedLamp on (Lamp is being used over a specified use time, replace lamp immediately)
Gray/BlueLamp off (Normal)
Gray/RedLamp off (Lamp is being used over a specified use time, replace lamp immediately)
Red/Blue with XLamp failure (Lamp failure, check lamp condition)
Red/Red with XLamp failure (Lamp failure and lamp is being used over a specified use time, replace lamp immediately)
Icon display/backgroundStatus
 BlueGood condition.
 Yellow/GrayFilter is almost clogged.
 Red/GrayFilter is clogged. Replace a filter with new one.
Indication of the filter status
Information 
						

							


Chapter 4 Controlling the Projector 
						

							
ENGLISH

4
ENGLISH
Chapter  
 Appendix 
5
Connection	examplesUse	of	telnet
Web	browser	setting Technical	data Q	&	A 
						

							


Chapter 5 Appendix

Examples of connection
Peer-To-Peer connection
Connecting the projector (PJ01) to the control computer (PC05) directly.
Projector Name: PJ01IP Address : 192.168.0.2Subnet Mask : 255.255.255.0Default Gateway : 0.0.0.0DNS : 0.0.0.0
Computer Name: PC10IP Address : 192.168.0.10Subnet Mask : 255.255.255.0Default Gateway : DNS : 
Computer Name: PC05IP Address : 192.168.0.5Subnet Mask : 255.255.255.0Default Gateway : DNS : 
Hub
Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 
Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway :  DNS :  
* UTP cross cable
Connecting the projector (PJ01) to the control computer (PC05) via the hub.
✐  When the projector is connected to the computer directly without hub, the UTP cross cable should be used.
To	another	network 
						

							

ENGLISH

 

The gateway (Router) installed in the network
Connecting the projector (PJ01) to the control computer (PC05) via the gateway.
To another network
Network Group: 192.168.200.x 
Network Group: 192.168.10.x 
Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 
Computer Name : PC205 IP Address : 192.168.200.5 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 
IP Address : 192.168.200.1
IP Address : 192.168.10.1 
IP Address : 192.168.100.1 
Computer Name: PC05 IP Address : 192.168.10.5 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 DNS : 192.168.201.1 
Computer Name : PC10 IP Address : 192.168.10.10 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 DNS : 192.168.201.1 
Computer Name : PC51 IP Address : 192.168.10.51 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 DNS : 192.168.201.1 
Computer Name : PC61 IP Address : 192.168.10.61 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.10.1 DNS : 192.168.201.1 
Gateway (Router) 
Hub 
Hub 
Hub 
Entrance hall 
Ofce
Examples of connection 
						

							


Chapter 5 Appendix

Use of telnet
You can control the projector by using the telnet application*1 installed on your computer.  
Normally, the telnet application is available on your computer.
* The telnet 10000 port is used to control the projector.
Control
(For example, in case of using the telnet 
application of Windows XP Professional.)
1.   Select 
Run... submenu from Start menu 
on  the  computer.  Type  "telnet"  onto  the 
Open text area on the displayed window 
and press OK  button. 
2.   The  telnet  application  will  start  and  the  following  window  will  be  displayed.  Type  as 
below to connect the projector.
  > open 192.168.1.201 10000 [return]
*    Use the IP address assigned to the projector.
(For example, in case of using the telnet 
application of Mac OS X v 10.4)
1.   Select 
Terminal from Applications	
-->Utilities.  
　Type  as below on the displayed window. 
      > telnet [return] 
						

							

ENGLISH

 

3.  When  communication  is  established  correctly,  the  word  "PASSWORD:"  appears  on  the 
window. Type the login password (Network PIN code*2) for the projector and then press 
"Enter" key on the keyboard. If you do not set up the Network PIN code, just press "Enter" 
key.
When the word "Hello" is replied, login has been succeeded.
* The password "1234" is used for the example. 
4.  Type the commands, refer to below table, to control the projector and then press "Enter" 
key for termination. For example, type "C00" which is a command to turn on the projec-
tor, and press "Enter" key. Confirm the projector is turning on.
* Enter with ASCII 64-byte capital characters and one-byte characters. 
To disconnect the communication, press "Ctrl" key and "]" key at the same time, type 
"close" and then press "Enter" key on the Keyboard.
  > close [return]
The table below shows the typical command lists for controlling this projector and please 
consult your local dealer for further information of another commands.
*1  Further instructions about the telnet application, please see the on-line guide on your computer.
*2    The password is a Network PIN code decided item "Network PIN code setting" (+pp.14, 23). If the authentication of the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please try again for the connection.
✐  If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection.
Command    Function
  C00    Power on
  C02  Power off
  C09  Volume up
  C0A  Volume down
  C0B  Audio Mute on
  C0C  Audio Mute off
  C1C  Menu display on
  C1D  menu display off
Command list table
Use of telnet 
						

							
50

Chapter 5 Appendix

Web browser setting
This  projector  is  designed  to  be  set  up  and  controlled  from  an  Internet  web  browser. 
Depending  on  the  preference  settings  of  the  web  browser,  some  control  functions  may 
not  be  available.  Please  make  sure  that  the  following  functions  are  set  up  properly  in  the 
web browser.
Active Script/JavaScript enable
There  are  some  control  items  used  with  the  JavaScript  function  in  the  setting  pages.  If 
the web browser is set not to use this JavaScript function, it may not control the projector 
properly. In this case, the warning message "Make sure JavaScript is ON." will be displayed 
on  the  top  of  the  page.  To  enable  the  JavaScript,  please  see  further  instructions  on  the 
next page.
Proxy setting
In  some  cases,  your  web  browser  is  set  up  to  use  the  prox y  ser ver  for  the  internet  or 
intranet connection. In this case, when you install this projector into the local network, you 
should set up the proxy setting of web browser preference correctly. Especially when con-
necting the projector and computer with a UTP cross cable directly, or when the network 
does  not  provide  the  proxy  server,  make  sure  that  "not  use  proxy  server"  is  set  up  in  your 
web  browser  preference.    Please  see  item  "Examples:  OS/Browsers"  in  the  next  page  for 
further setting up procedure.
✐  There are various ways to change your browser preferences depending on the version or applica-tions. Please see the setting instructions on next page for example and also refer to on-line help of your web browser.