Sanyo Projector Plc Xc56 User Manual

							
ENGLISH

11
ENGLISH
Chapter 2 
 Setup Procedures
2
Describes how to configure the network. 
						

							
1

Chapter 2 Setup Procedures

Setting Procedure
Setting procedures and contents differ depending on the LAN installation location.  
When installing, consult your system administrator to set up the LAN appropriately.
Connect the LAN cable to the LAN connection terminal of the projector.
Network configuration
Set the Wired LAN network through the projector menu. Detailed network settings will be 
made  with  browser.  Refer  to  “3.  Basic  setting  and  operation”  (p.17-30).  First,  complete  the 
settings  described  in  this  chapter  before  performing  steps  in  “3.  Basic  setting  and  opera-
tion.”
1. Select “LAN mode select” in the Network menu, and press Point  8 or SELECT button.
2.   Select  similar  LAN  environment  among  LAN1,  LAN2  and  LAN3  with  the  Point 
ed but-
tons. Then the Menu will disappear, the “Please wait...” message will appear, and switch-
ing  operation  will  start.  Switching  will  take  a  while  and  the  projector’s  LINK /ACT  Lamp 
will  be  on  or  blink,  and  after  completing  the  operation,  the  “Please  wait...”  message  will 
disappear.
Connecting to the LAN line
LAN	Cable
LAN	Connection	 Terminal
LINK Lamp (Green)Light green when the projector is connected to the network correctly.
ACT Lamp (Orange)Blink orange when the projector is sending or receiving the data. 
						

							
1
ENGLISH

 

*1 Set "On" only when the DHCP server is available on your network environment.*2 Set [255.255.255.255] if the network does not provide the gateway (router).*3 Set [255.255.255.255] if you do not use the function E-mail alert.
3.  Select  "Network  setting"  in  the  Network  menu  and  press SELECT  button,  and  then  the 
LAN setting screen will appear and selected LAN settings will be displayed. Adjust each 
item  to  the  setting  environment.  Consult  your  system  administrator  about  the  detailed 
settings.
  Press 
SELECT button in a row where you want to adjust, and adjust the figures with the 
Point ed  buttons  and  move  among  the  items  with  the  Point 7  8  buttons,  and  then 
press SELECT button to fix. Move to the next row with the Point ed buttons to adjust.
4.  After  completing  all  the  settings,  select “Set ”  and  press SELECT  button.  Now,  all 
procedures  have  been  done. To  cancel  the  adjusted  settings,  select  "Cancel"  and  press 
SELECT button.  
You  can  confirm  the  LAN  settings  you  have  made  from “Network  information”  (p.14).  In 
such cases  that the LAN cannot be connected, see this screen.
Network	setting
DHCP:	On
Item  Description
DHCP	....................	Sets DHCP function On or Off. When you setup the network setting manually, select "Off ". When it is set On, IP address, Subnet, Gateway  and DNS are automatically set according to your network environment 	*1.
IP	address  .............Sets IP address of the projectorSubnet  ....................Sets Subnet mask. Normally sets 255.255.255.0Gateway*2 .............Sets IP address of the default gateway (Router)DNS*3  .......................  
Sets IP address of the DNS server.
DHCP:	Off
Network configuration 
						

							
1

Chapter 2 Setup Procedures

The Network PIN code is to restrict the access from the networks to the projector.
After  setting  the  Network  PIN  code,  you  need  to  enter  it  to  operate  the  projector  via  the 
networks.
Network PIN code
Network information
1. Select "Network PIN code" in the Network menu, and press SELECT button. 
  The Network PIN code screen will appear.
2. Set the Network PIN code.
Set the figures with the Point ed buttons and move to the next items with the Point	7 
8 buttons. Select “Set” and press SELECT button to set. To cancel the preset Network PIN 
code, select “Cancel”. When you do not want to set the Network PIN code, set "0000".
It is recommended to set the Network PIN code if you use the projector via the networks.  
The  Network  PIN  code  can  be  set  also  through  the  networks.    See “3.  Basic  setting  and 
operation”	➔ 	“Initial setting”	➔ 	“Network PIN code setting” (p.23).
Select "Network information" in the Network menu and press Point  8 or SELECT button 
to  show  LAN  setting  environment  of  the  currently  selected  projector.  (The  description 
below is an example and different from what will be shown.)
Network	PIN	code
Network	PIN	code	screen 
						

							
15
ENGLISH

 

Network factory default
1. Select “Network factory default” in the Network menu and press SELECT button.
2. A confirmation box appears and select "Yes" and then press SELECT button.
3. Another confirmation box appears and select "Yes" and then press SELECT button.
4.   All  the  wired  LAN  settings  will  go  back  to  the  factory  default  settings.  For  details,  refer  to 
“Wired LAN factory default settings” (p.16).
Network factory default 
						

							
1

Chapter 2 Setup Procedures
Wired LAN factory default settings
ParameterSELECTED	LAN
LAN	1 LAN	2LAN	3
IP	CONFIGURATION
MANUALDHCPMANUAL
IP	ADDRESS
169.254.100.100192.168.100.100192.168.100.100
SUBNET	MASK
255.255.0.0255.255.255.0255.255.255.0
GATEWAY	ADDRESS
255.255.255.255255.255.255.255255.255.255.255
DNS	ADDRESS
255.255.255.255255.255.255.255255.255.255.255 
						

							
ENGLISH

17
ENGLISH
Chapter 3 
 Basic Setting and Operation
3
Describes  basic  operations  and  settings  for  controlling  the  projec-
tor  by  using  the  web  browser.  It  is  required  that  computer  and 
projector  is  connected  to  the  network  and  the  network  address  is 
properly configured. 
						

							
1

Chapter 3 Basic Setting and Operation

Login the setting page of the projector
[1] Enter the IP address
Launch  the  web  browser  installed  in  your 
computer,  enter  the  IP  address  into  the 
"Address"  on  the  browser  and  then  press 
"Enter" key.
Enter  the  address  that  you  configured  in 
item "Network configuration" (+ p.12).
[2] Login
 
If  the  setting  page  has  set  the  password,  the  authentication  window  will  appear.  In  this 
case  type  "user"  onto  the User  Name  text  area  and  the  login  Network  PIN  code  onto 
the Password text area and then click OK (Log in) button.*  The entering User Name must be "user" and it can not be changed.
[Note]
  When accessing the projector for the first time or the Network 
PIN code "0000" is set, the auto-login will be performed and the next main setting page is displayed. 
						

							
1
ENGLISH

 

[3] Display of main setting page
The  following  main  set ting  page  will  be  displayed  according  to  your  display  mode 
selection. Perform various kinds of settings through this page. Click on the menus to dis-
play the control and setting pages.
Main setting page in the display
Setting page
Displays the control and setting items according to the selected menu.
Main menu
For selection of  control and setting items of the projector. 
Sub menu tabSwitches the sub menu tab.
Login the setting page of the projector 
						

							
0

Chapter 3 Basic Setting and Operation

How to use the setting page
To control and set up the projector, use the setting menus on the web browser. Describes the 
basic operation and procedures commonly used on this manual.
The  setting  menu  appears  when 
clicking the sub menu tab. 
* Each item has a valid setting range respectively.
Example of the setting page
✐		The value in the text box indicates current value.
✐ 
  Each item has a valid setting range. The setting value exceeding this becomes invalid. Some con-trol items can not be used depending on the selecting input mode or functions of the projector you use. In this case, the values of those items are indicated with "---".
Text box setting
Enter a number or text and then click Set button.
or 
Change a value with – or + button.
Pull-down menu setting
Select an item with pull-down menu button and then click Set button.
Types of setting