Sanyo Projector Plc Wxe45 User Manual

51
How to Use the Antitheft Alarm Function
The	Antitheft	 alarm	function	 is	to	 prevent	 the	projector	 from	being	 stolen.	 	 With	this	function	 on,	the	alarm	 rings	
when	an	unauthorized	person	tries	to	move	the	projector.
Press	 the	F	button	 twice	to	turn	 the	alarm	 function	 on.	 	The	
ALARM	 indicator	 blinks	for	a	few	 seconds	 and	the	projector	
enters	the	warning	mode.
While	 the	Antitheft	 alarm	function	 is	on,	 the	projector	 emits	a	
low-pitched	sound	when	detecting	a	vibration.		
When...

5
CAUTION:
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE 
DOWN THE NEW PIN CODE  AND KEEP IT SECURELY .  
IF YOU FORGET  YOUR PIN CODE, SOME SETTINGS 
OF THE ALARM FUNCTION CAN NO LONGER BE 
CHANGED.
Chan�e the PIN code 
Press	the 	F 	button 	and 	enter 	the 	four-digit 	PIN 	code	
within	 about	10	seconds.	 	 The	ALARM	 indicator	 blinks	
red	for 	a 	few 	seconds 	and 	high-pitched 	confirmation	
sound	is	made.		
Settin�s
Reset the settin�s
Select 	Factory 	default 	in 	the 	Setting 	menu 	to 	reset...

5
How to install the battery
To	use 	the 	Antitheft 	alarm 	function, 	you 	need 	to 	install 	a	
battery.	(Use	CR2	3V	lithium	battery.)	
Unplug 	the 	AC 	power 	cord 	from 	the 	wall 	outlet 	before	
installing 	the 	battery. 	Remove 	the 	screw 	and 	open 	the	
battery	cover	on	the	bottom	of	the	projector.
When	 the	battery	 is	installed	 properly,	 the	ALARM	 indicator	
blinks	for	about	10	seconds.
After	placing 	the 	battery, 	put 	the 	cover 	back 	and 	secure 	it	
with	the	screw.
When 	the...

54
The	WARNING	indicator	shows	the	state	of	the	function	which	protects	the	projector.	Check	the	state	of	the	
WARNING	indicator	and	the	POWER	indicator	to	take	proper	maintenance.	
Top Panel
Warnin� Indicator
The projector is shut down and the WARNING 
indicator is blinkin� red.
When	the	temperature	inside	the	projector	reaches	a	
certain	level,	the	projector	is	automatically	shut	down	to	
avoid	overheating.	The	POWER	indicator	is	blinking	while	
the	projector	is	being	cooled	down.	When	the	projector...

55
Turn	off	the	projector,	and	unplug	the	AC	power	cord	
from	the	AC	outlet.
Turn	over	the	projector	and	remove	the	air	filters	by	
pulling	the	latches	upward.
1
2
Air	filters	prevent	dust	from	accumulating	on	the	surface	of	the	optical	elements	inside	the	projector.	Should	the	
air	filters	become	clogged	with	dust	particles,	they	will	reduce	cooling	fans’ 	effectiveness	and	may	result	in	a	
buildup	of	internal	heat	and	adversely	affect	the	life	of	the	projector.	Clean	the	air	filters	by	following	the...

5
Cleanin� the Projector Cabinet
Unplug	the	AC	power	cord	before	cleaning.
Gently	wipe	the	projector	body	with	a	soft	dry	cleaning	
cloth.	When	it	is	heavily	soiled,	use	a	small	amount	of	mild	
detergent	and	finish	with	the	cleaning	cloth.	 Avoid	excessive	
use	of	cleaner.	Abrasive	cleaners,	solvents,	or	other	harsh	
chemicals	might	scratch	the	surface	of	the	cabinet.
When	the	projector	is	not	in	use,	put	the	projector	in	an	
appropriate	case	to	avoid	dust	and	being	scratched.
Unplug	the	AC	power...

57
Follow	these	steps	to	replace	the	lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement	lamp	can	be	ordered	through	your	dealer.	When	ordering	a	projection	lamp,	give	the	following	
information	to	the	dealer.
●Model No. of your projector  : PLC-WXE45
●Replacement Lamp Type No. : POA-LMP10POA-LMP10 
(Service	Parts	No.	610	332	3855)
For	continued	safety,	replace	with	a	lamp	of	the	
same	type.	Do	not	drop	a	lamp	or	touch	a	glass	
bulb!	The	glass	can	shatter	and	may	cause	injury.
Allow	the	projector	to...

58
Be	sure	to	reset	the	Lamp	replacement	counter	after	the	lamp	is	replaced.	When	the	Lamp	replacement	counter	
is	reset,	the	LAMP	REPLACE	indicator	stops	lighting.
Turn	the	projector	on	and	press	the	MENU	button	
to	display	the	On-Screen	Menu.	Use	the	Point	◄► 
buttons	to	move	the	red	frame	pointer	to	the	Setting	
Menu	icon.
Use	the	Point	▲▼	buttons	to	move	the	red	frame		
pointer	to	Lamp	counter	and	then	press	the	SELECT 	
button.	The	first	dialog	box	appears	showing	the	total	
accumulated	lamp	time...

59
Troubleshootin�
Before	calling	your	dealer	or	service	center	for	assistance,	check	the	items	below	once	again.
–	Make	sure	you	have	properly	connected	the	projector	to	peripheral	equipment	as	described	on	pages	14-16.
–	Make	sure	all	equipment	is	connected	to	the	 AC	outlet	and	the	power	is	turned	on.
–	When	you	operate	the	projector	with	a	computer	and	it	does	not	project	an	image,	restart	the	computer.
Problem:–	Solutions
No power
–	Plug	the	power	cord	of	the	projector	into	the	 AC	outlet.
–	See	if...

0
Picture is not bri�ht enou�h.
– Check if "Contrast" or "Brightness" are adjusted properly (see	 	Check if "Contrast" or "Brightness" are adjusted properly (seeCheck	if	"Contrast"	or	"Brightness"	are	adjusted	properly	(see(see	
pages	31,	38)..
– Check if "Image level" is selected properly (see pages 30	 Check if "Image level" is selected properly (see pages 30Check	if	"Image	level"	is	selected	properly	(see pages 30(see	pages...