Sanyo Plc Xm100l Projector User Manual

1

Remote Control
POINT ▲▼◄►buttons
KEySTONE button
Basic Operation
If a projected picture still has keystone distortion after pressing 
the AUTO PC button on the remote control, correct the image 
manually as follows:
Press the KEYSTONE button on the remote control to switch the 
Standard (for Vertical/Horizontal) /Corner correction adjustment. 
The Standard or Corner correction adjustment dialog box appears. 
Use the Point ▲▼◄► buttons to correct the Standard or Corner 
distortion. The Standard...



Pointer
Note:   You	can	choose	the	pattern	of	Pointer	(Arrow/Finger/Dot )	in	the	
Setting	Menu	(p.58)
You can move the Pointer of the projector with the remote control to emph\
asize a part of the projected image.  
Press the POINTER button to activate the Pointer function.1


MOUSE POINTER button
POINTER button
To cancel the Pointer function, press the POINTER button 
again or press any other button. 
Use the MOUSE POINTER button to move the Pointer. 
The remote control can be...



The input source changes each time you press the INPUT button on the side control or the remote control as follows:
 Input 1→ Input 2→ Input 3 → ...
Before using the INPUT button on the side control or the remote control, you must select a cor\
rect input source by On-
Screen Menu and the latest input source will be displayed.
Input Selection
Press the INPUT 1, INPUT 2, or INPUT 3 button on the remote control. The input source appears on the screen as you 
press each button. Select the...

4

INPUT MENU
When your computer is connected to INPUT 1 (DIGITAL) 
terminal, select RGB(PC digital).
When your computer is connected to the INPUT 1 (ANALOG) 
terminal, select RGB (PC analog).
RGB(PC digital)
RGB(PC analog)
Note:
	 •	 Input	source	changes	if	the	INPUT	1	button	on	the	remote	control	is	pressed.
	 •	 HDCP 	(High-bandwidth	Digital	Content	Protection)	is	a	system	for	
protecting	digital	entertainment	content	which	is	delivered	by	DVI	
(Digital	Visual	Interface)	from	being	copied.	The...

5

When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack, select Video.
When the video input signal is connected to the 
S-VIDEO jack, select S-video.
When connecting to video equipment, select the type of Video 
source in the Source Select Menu. 
When the video input signal is connected to the 
Y-Pb/Cb-Pr/Cr jacks, select 
y,Pb/Cb,Pr/Cr.
When the video input signal is connected to the 
VIDEO jack,...

6

Computer Input
System                                             SVGA 1
Input 1                                               RGB(PC analog)Input 2                                               RGBInput 3                                               Video
PC System Menu
PC System Menu1

PC system can also be selected manually.
The PC System Menu  
Selected system is    
displayed.
Press the MENU button to display the On-Screen Menu. Use 
the Point ▲▼ buttons to select Input and then press...

7

Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Position H and Position V positions to 
conform to your computer. 
To store the adjusted parameters .The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting Mode in PC SYSTEM Menu (p.36). See “Manual PC Adjustment” on pages 38-39.
Note:
	 •	 Fine	sync,	Total	dots,	Position	H	and	Position	V	position	of	certain...



Some computers employ special signal formats which may not be tuned by M\
ulti-Scan system of this projector. Manual PC 
Adjustment enables you to precisely adjust several parameters to match t\
hose special signal formats. The projector has 
10 independent memory areas to store those parameters manually adjusted.\
 It allows you to recall the setting for a specific 
computer. 
Note:  The	PC	Adjust	Menu	cannot	be	operated	when	the	digital	signal	input	on	the	DVI	terminal	is	selected	on	PC...

9

Computer Input
Note:
•	Display area (H/V)	cannot	be	selected	when	480i,	575i,	
480p ,	575p,	720p,	1035i 	or	1080i	is	selected	in	the	PC	
System	Menu	(p.36).
•	When	input	computer	signal	to	the	projector,	PC	adjust	function will	become	available.
Auto PC adj.Fine syncTotal dots                                                               1\
366Position H                                                              \
0Position V                                                              \...

40

1

Normal picture level preset on the projector.
Picture level with improved halftone for graphics.
User preset picture adjustment in the Image adjust Menu. (p.42)
Computer Input
Image select Menu
Press the MENU button to display the On-Screen Menu. 
Use the Point ▲▼ buttons to select Image select and 
then press the Point ► or the SELECT button.
Use the Point ▲▼ buttons to select the desired item 
and then press the SELECT button.
StandardRealImage 1Image 2Image 3Image 4Image 5Image 6Image...