Sanyo Plc Xm100l Projector User Manual

1

Mechanical Information 
 Projector Type  Multi-media Projector
 
  Dimensions (W x H x D)  PLC-XM100L/PLC-XM150L: 19.25” x 6.46” x 14.57” (489.5 mm x 164.0 mm x 370.1 mm)
 
    PLC-XM100/PLC-XM150    : 19.25” x 6.46” x 17.08” (489.5 mm x 164.0 mm x 433.8 mm)\
 
  Net Weight  PLC-XM100L/PLC-XM150L: 20.5 lbs (9.3 kg)
 
    PLC-XM100/PLC-XM150    : 22.3 lbs (10.1 kg)
 
  Feet Adjustment  0˚ to 4˚         
Panel Resolution 
  LCD Panel System  0.8” TFT Active Matrix type, 3 panels 
 
  Panel...



The lens of this projector can be replaced with other optional lens. This feature enables you to use the projector for wide variety of uses.For installation and replacement of the lens, always contact the sales d\
ealer. The projector lens must be installed or replaced by well-trained sales or service engineers. Do not attempt to install an\
d replace the lens by yourself as it may cause injury.
Do not hold the lens when carrying or lifting the projector. It may cause serious damage to the...



ANALOG/ MONITOR OUT (Mini D-sub 15 pin)
512341096781514131112
CONTROL PORT CONNECTOR (D-sub 9 pin)
-----
R X D
T X D
-----
SG
-----
RTS
CTS
Serial
1


4
5
6
7

DIGITAL DVI-D (DVI 4 PIN)
1917
21018
31119
41220
51321
61422
71523
81624
T.M.D.S. Data2–
No Connect
T.M.D.S. Data2+
No Connect
T.M.D.S. Data2 Shield
DDC Clock
DDC Data
No Connect
1
5

4

6
7

T.M.D.S. Data1–
No Connect
T.M.D.S. Data1+
No Connect
T.M.D.S. Data1 Shield
+5V Power
Ground (for +5V)
Hot...

4

Write down the PIN code number in the column below and keep it with this \
manual securely. If you forgot or lost 
the number and unable to operate the projector, contact the service station. 
Factory default set No:  1   4*
Factory default set No:  4   1*
*  S h o u l d   t h e   f o u r - d i g i t   n u m b e r   b e 
changed,  the  factory  set  number  will 
be invalid.
Put the label below (supplied) on in a prominent place of 
the projector’s body while it is locked...

5

(14.57)370.1
(3.31)84.
0(5.76)164.0
(18.58)472.0
(19.27)489.5
6.25(158.8)3.78(96.0)
(3.54)90.0
(5.31)135.0
(3.94)100.0
(3.54)90.0
5 MAXº 

Unit: inch (mm)
Appendix
(17.08)433.8
(3.31)84.
0(5.76)164.0
(18.58)472.0
(19.27)489.5
6.25(158.8)3.78(96.0)
(3.54)90.0
(5.31)135.0
(3.94)100.0
(3.54)90.0
5 MAXº 
Dimensions
PLC-XM100L, PLC-XM150L
PLC-XM100, PLC-XM150
Screw Holes for 
Ceiling Mount
Screw: M6
Depth: 0.393 (10.0) 

6

Appendix
This projector provides a function to control and monitor the projector'\
s operations by using the RS-232C serial port.
Connect a RS-232C serial cross cable to CONTROL PORT 
on the projector and serial port on the PC.  (See p.19)
Launch a communication software provided with PC and 
setup the communication condition as follows:
1


Baud rate : 9600 / 19200 bps
Parity check  : none
Stop bit    : 1
Flow control  : none
Data bit    : 8
Type the command for controlling the...

7

The command is sent from PC to the projector with the 
format below;
     'C' [Command] 'CR'
        Command: two characters (refer to the command 
table below.
-The projector decodes the command and returns the 'ACK'   
 with the format below;
     'ACK'  'CR'
-When the projector can not decode the command, it returns  
 with format below.
     ‘?’  ‘CR’ 
Format
Appendix
CommandFunction
C00Turn the projector ON
C01Turn the projector OFF 
(immediately...


Appendix
The command is sent from PC to the projector with the 
format below;
     'CR' [Command] 'CR'
        Command: one character (refer to the command table 
below.
The projector decodes the command and returns the 
'Character string' with the format below;
Format
The tables on page 87 and 88 show the typical command lists for controll\
ing the projector.  Please consult your local dealer 
for further information of other commands.
CommandFunctionProjector...

KA8AL