Sanyo Plc Xl51projector User Manual

51
Setting
Remote control
This projector provides two different remote control codes; 
the factory-set, initial code (Code 1) and the secondary code 
(Code 2). This switching function prevents remote control 
interference when several projectors or video equipment 
are operated at the same time.  
When the projector is operated in “Code 2,” both the 
projector and the remote control must be switched to 
“Code 2.”
 
To change the code for the projector:
Select either “Code 1” or “Code 2” in this Setting...

5252
Setting
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
Off……  The projector is not locked with the PIN code.
On1……  Requires to enter a PIN code every time turning on 
the projector.  
On2……  Requires to enter a PIN code to operate the 
projector once the power cord is unplugged; as long 
as the AC power cord is connected, the projector 
can be operated without a PIN code.
Whenever you change...

5353
Setting
The PIN code can be changed to your desired four-digit 
number.  
Select "PIN code change" with the Point 
d button, and 
press the SELECT button to display the New PIN code 
input dialog box.
Select a number by pressing the Point 
ed buttons. And 
then press the Point 
8 button to fix the number and 
move the pointer. Repeat it to complete entering a four-
digit number. After entering the four-digit number, move 
the pointer to "Set" by pressing the Point 
8 button. Then...

54
Setting
Lamp counter 
This function provides the following options in the cooling 
fans’ operation after turning off the projector (p.21).
L1 …… Normal operation
L2 ……  Slower and lower-sound than the normal operation (L1), 
but it takes longer to cool down the projector.
Fan
This icon appears on the screen when the end of 
lamp life is approaching.
✔Note:
 • The Lamp replacement icon will not appear when the Display 
function is set to “Off” (p.46), during “Freeze” (p.25), or “No 
show” (p.26).
Lamp...

55
Setting
Factory default
This function returns all setting values except for the user 
logo, PIN code lock, Logo PIN code lock, the lamp counter, 
and the filter counter to the factory default settings.
Select Factory default and this box 
appears.  Select “Yes,” and the next 
box appears. 
Factory default
Select “Yes” to 
activate it.Exit the Setting Menu.
Quit
Filter counter
Use the Point 7 8 buttons 
to set the timer. Select 
from (Off/100H/ 200H/ 
300H) depending on the 
use environment.
This...

56
How to Use the Antitheft Alarm Function
Antitheft alarm function is provided to prevent the projector from being stolen. When this function is set to 
“On,” the alarm rings as an unauthorized person tries to move the projector.
To activate the Alarm function for the first time after purchase, you must turn on the power once. 
Press the F button three times to turn the alarm function 
on. The ALARM indicator blinks for a few seconds and the 
projector enters the warning mode. (If the battery is not...

57
Antitheft Alarm Function
CAUTION:
WHEN yOU HAVE CHANGED THE PIN CODE,  WRITE DOWN 
THE  NEW  PIN CODE  IN COLUMN  OF THE  PIN CODE  NO.MEMO 
ON PAGE 75,  AND KEEP IT SECUREL y. IF yOU FORGET y OUR 
PIN CODE, SOME SETTINGS OF THE ANTITHEFT ALARM 
FUNCTION CAN NO LONGER BE CHANGED .
Change the PIN code 
Press the F button and enter the four-digit PIN code 
number within about 10 seconds. The ALARM indicator 
blinks red for a few seconds and a high-pitched 
confirmation sound is produced.  
Other...

58
Charge the built-in battery pack
As long as the AC power cord is connected, the built-in 
battery for Alarm function is being charged at all times. 
While charging the battery, “Charging” is displayed in the 
menu. 
The “Charging” appears dimmed when the battery is fully 
charged or if charging malfunction occurs. ✔Note:
 •    The PIN code and settings you have changed are 
effective even after the battery is changed.
  • When replacing the rechargeable battery pack, protect 
the infrared remote...

59
SAFETy PRECAUTIONS FOR SANy O Ni-MH BATTERy PACK
Observe the following precautions when handling the built-in battery pack of the projector:
 l  MAKE SURE THAT THE BATTERY PACK IS INSTALLED IN THE PROJECTOR WHEN RECHARGING. 
USING THE CHARGERS OTHER THAN THE PROJECTOR MAY CAUSE EXPLOSION OR A FIRE.
  l  The rechargeable battery pack is for use exclusively with this projector. Do not use in other products or 
this may cause accident.
  l  Do not throw the battery into fire or heat it. Doing so may...

60
The WARNING indicator shows the state of the function which protects the projector. Check the state of the 
WARNING indicator and the POWER indicator to take proper maintenance. Indicators
Warning Indicator
The projector is shut down and the WARNING 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector is automatically shut down to 
avoid overheating. The POWER indicator is blinking while 
the projector is being cooled down. When the projector...