Sanyo Plc Xl51projector User Manual

							51
Setting
Remote control
This projector provides two different remote control codes; 
the factory-set, initial code (Code 1) and the secondary code 
(Code 2). This switching function prevents remote control 
interference when several projectors or video equipment 
are operated at the same time.  
When the projector is operated in “Code 2,” both the 
projector and the remote control must be switched to 
“Code 2.”
 
To change the code for the projector:
Select either “Code 1” or “Code 2” in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons 
together for more than 5 seconds. After changing the code, 
make sure the remote control operates properly. 
Remote control
Press and hold 
MENU and 
IMAGE buttons 
for more than 5 
seconds.
✔Note:
• When different codes are set on the projector and on the 
remote control, any operation cannot be made. In that 
case, switch the code on the remote control to fit the 
code on the projector.
•  If the batteries are removed from the remote control for a 
long period of time, the remote control code will be reset. 
Security (Key lock, PIN code lock, Alarm settings)
This function allows you to use the Key lock, PIN code lock, 
and Alarm function to set the security for the projector 
operation.
Key lock
This function locks the top control and remote control 
buttons to prevent operation by unauthorized persons.
 ..... Unlocked.
 .....  Lock the operation of the top control. To 
unlock, use the remote control.
 .....  Lock the operation of the remote control.    
To unlock, use the top control.
If the top control accidentally becomes locked and 
you do not have the remote control nearby or there is 
something wrong with your remote control, contact the 
dealer where you purchased the projector or the service 
center.
Key lock
Select Key lock. Use 
the Point 
ed buttons 
to choose one of the 
options and select 
[Yes] to activate it.
Lamp control
You can change the brightness of the screen.
Normal …   Normal brightness 
Auto ……   Brightness according with the input signal 
Eco ……     Lower brightness reduces the lamp power 
consumption and extends the lamp life. 
						

							5252
Setting
PIN code lock
This function prevents the projector from being operated 
by unauthorized persons and provides the following 
setting options for security.
Off……  The projector is not locked with the PIN code.
On1……  Requires to enter a PIN code every time turning on 
the projector.  
On2……  Requires to enter a PIN code to operate the 
projector once the power cord is unplugged; as long 
as the AC power cord is connected, the projector 
can be operated without a PIN code.
Whenever you change the PIN code lock setting or the 
PIN code (a four-digit number), you are required to enter 
the PIN code. “1234” is set as the initial PIN code at the 
factory.
When the projector is locked 
with the PIN code, the PIN 
code lock symbol appears on 
the menu bar. 
PIN code lock
Enter a PIN code
Select a number by pressing the Point ed buttons.  
And then press the Point 
8 button to fix the number 
and move the pointer. The number changes to "✳".  If 
you fixed an incorrect number, move the pointer to the 
number you want to correct by pressing the Point 
7 
button, and then select the correct number by pressing 
the Point 
ed buttons.
Repeat this step to complete entering a four-digit 
number.
After entering the four-digit number, move the pointer to 
"Set" by pressing the Point 
8 button.  Press the SELECT 
button so that you can change the following PIN code 
lock settings.  If you entered an incorrect PIN code, "PIN 
code" and the number (✳✳✳✳) turns red. Enter a correct
PIN code all over again. Enter a PIN code
The input numbers change 
to “✳” for security reasons.
Move the pointer to "Set" by 
pressing the Point 
 8 button.  
And then press the SELECT 
button. 
						

							5353
Setting
The PIN code can be changed to your desired four-digit 
number.  
Select "PIN code change" with the Point 
d button, and 
press the SELECT button to display the New PIN code 
input dialog box.
Select a number by pressing the Point 
ed buttons. And 
then press the Point 
8 button to fix the number and 
move the pointer. Repeat it to complete entering a four-
digit number. After entering the four-digit number, move 
the pointer to "Set" by pressing the Point 
8 button. Then 
press the SELECT button.
Change the PIN code 
Change the PIN code
Select PIN code change and 
press the SELECT button. 
The New PIN code input 
dialog box appears.
Change the PIN code lock setting
CAUTION:
WHEN y OU HAVE CHANGED THE PIN CODE,  WRITE 
DOWN  THE NEW PIN CODE IN COLUMN OF  THE 
PIN CODE NO . MEMO ON PAGE 75,  AND KEEP IT 
SECUREL y. IF yOU FORGET y OUR PIN CODE,  THE 
PROjECTOR CAN NO LONGER BE STARTED .
Select Off, On1, or On2 with the Point 7 8 buttons and 
then move the red frame pointer to “Quit” with the Point 
d button. Press the SELECT button to close the dialog 
box.
Change the PIN code lock setting
Select a desired setting with the 
Point 
7 8 buttons.
The input numbers 
are being displayed for 
confirmation.
Alarm
This function allows you to configure the Alarm 
operation. See “How to Use the Antitheft Alarm 
Function” on pages 56-59. 
						

							54
Setting
Lamp counter 
This function provides the following options in the cooling 
fans’ operation after turning off the projector (p.21).
L1 …… Normal operation
L2 ……  Slower and lower-sound than the normal operation (L1), 
but it takes longer to cool down the projector.
Fan
This icon appears on the screen when the end of 
lamp life is approaching.
✔Note:
 • The Lamp replacement icon will not appear when the Display 
function is set to “Off” (p.46), during “Freeze” (p.25), or “No 
show” (p.26).
Lamp Replacement icon
 
This function is used to reset the lamp counter. 
When the lamp life is left less than 100 hours, the Lamp 
replacement icon appears on the screen, indicating that the 
end of lamp life is approaching.
When the lamp life is counted down to 0 hour, the Lamp 
replacement icon (Fig.2) will appear on the screen, 
indicating that the end of lamp life is reached.
When replacing the projection lamp, reset the lamp counter. 
See “Lamp Replacement Counter” on page 64.
Fig.2   Lamp replacement icon
✔Note:
 •  At turning on, the icon (Fig.2) will appear.　
At selecting input source, the icon (Fig.1) will 
appear. Fig.1   Lamp replacement icon
This icon appears on the screen when the end of
lamp life is reached.
✔Note:
  •  This icon also appears at turning on and　
selecting input source.
Fan Control
Warning log
This function records anomalous operations while the 
projector is in operation and use it when diagnosing faults. 
Up to 10 warning logs are displayed with the latest warning 
message at the top of the list, followed by previous warning 
messages in chronological order.
✔Note:
•  When the Factory default function is executed, 
all the warning log records will be deleted.
Choose the running speed of cooling fans from the following 
options according to the altitude in which the projector is 
being used.
Off.......  Normal speed. Set this function to “Off” when using 
the projector in non-high altitude environment.
On 1...   Faster than Off mode. Select this mode when using 
the projector in high altitudes (about 1,200 meters or 
more above the sea level) where the fans have less 
cooling effect.
On 2....  Faster than On 1 mode. Select this mode when using 
the projector in higher altitudes than above where the 
fans have lesser cooling effect.
 
✔Note:
 • Setting “Fan control” to On1 or On2 affects 
L2 operation in “Fan.”
✔Note:
  • Fan noise becomes louder in On 1 and On2.
  • Failure to set the running speed of cooling 
fans properly may affect the projector life. 
						

							55
Setting
Factory default
This function returns all setting values except for the user 
logo, PIN code lock, Logo PIN code lock, the lamp counter, 
and the filter counter to the factory default settings.
Select Factory default and this box 
appears.  Select “Yes,” and the next 
box appears. 
Factory default
Select “Yes” to 
activate it.Exit the Setting Menu.
Quit
Filter counter
Use the Point 7 8 buttons 
to set the timer. Select 
from (Off/100H/ 200H/ 
300H) depending on the 
use environment.
This function is used to set a frequency for the filter 
cleaning.
When the projector reached a specified time between 
cleanings, a Filter warning icon appears on the screen, 
notifying the cleaning is necessary. After cleaning the 
filter, be sure to select RESET and set the timer. The Filter 
warning icon will not turn off until the filter counter is reset.
For details about resetting the timer, refer to “Resetting the 
Filter Counter” on page 61. Filter counter 
Filter warning icon (Fig.3) appears on the screen 
at a set time.
✔Note:
•  
At selecting input source, the icon (Fig.4) will appear.
•  The Filter warning icon (Fig.3 and Fig.4) will not appear when 
the Display function is set to “Off” (p.46), during “Freeze” 
(p.25), or “No show” (p.26).
✔Note:
  •  The icon (Fig.3) appears at turning on.
Fig.4  Filter warning icon
Fig.3  Filter warning icon
Test pattern
Various  test  patterns  are  available  for  use  when  setting  up 
the projector. 
						

							56
How to Use the Antitheft Alarm Function
Antitheft alarm function is provided to prevent the projector from being stolen. When this function is set to 
“On,” the alarm rings as an unauthorized person tries to move the projector.
To activate the Alarm function for the first time after purchase, you must turn on the power once. 
Press the F button three times to turn the alarm function 
on. The ALARM indicator blinks for a few seconds and the 
projector enters the warning mode. (If the battery is not 
charged enough for the alarm function to operate normally, 
it bleeps and the Alarm indicator will blink red every 20 
seconds.)
During the Antitheft alarm function is on, the projector 
emits a low-pitched sound when it detects vibration.
When the projector does not detect vibration for a few 
seconds after the sound, it goes back to the warning mode.
When the projector detects more vibrations after the low-
pitched sound, the alarm starts ringing.
The Alarm operating configuration (Alarm volume, 
Sensitivity, and Ringing time) can be selected in the menu. 
See page 57.
Set the alarm
Release the alarm setting
✔Note:
  •This function is not a guarantee against stealing.
  • The alarm does not ring while the AC power cord is connected to an outlet even if the projector detects 
vibrations.
  •The alarm will stop, as the AC power cord is connected to an outlet, except when the battery cover is open.
  • Pressing the buttons is always accompanied by a sound. If no sound is produced after pressing a button, 
you need to press it again.
Set and release the Antitheft alarm function
✔Note:
  • You can test the alarm sound without setting the alarm 
function. Press and hold the F button, then the alarm 
starts ringing. The duration of the alarm sound is the 
same as the “Ringing Time” setting (p.57).
  • If you want to stop the alarm while it is ringing, insert 
the AC power cord to an outlet or press the F button and 
enter the four-digit PIN code number.
The Alarm function is operated by a built-in rechargeable 
battery.  The alarm will not work properly if the battery is not 
charged enough. See page 58 for details.
Press the F button and enter the four-digit PIN code number 
within about 10 seconds. (The default PIN code is set to 
“1111.”) When the alarm is released, you will hear a high-
pitched confirmation sound.
When you enter an incorrect PIN code, you will hear a low-
pitched sound. If you enter an incorrect PIN code three  
times in a row, the alarm will start ringing.
The Alarm setting and release and PIN Code change can be 
made without an AC power connection.
Antitheft Alarm Function
Indicator
ALARM indicator
Terminal
F buttonButton 1, 2, 3 
						

							57
Antitheft Alarm Function
CAUTION:
WHEN yOU HAVE CHANGED THE PIN CODE,  WRITE DOWN 
THE  NEW  PIN CODE  IN COLUMN  OF THE  PIN CODE  NO.MEMO 
ON PAGE 75,  AND KEEP IT SECUREL y. IF yOU FORGET y OUR 
PIN CODE, SOME SETTINGS OF THE ANTITHEFT ALARM 
FUNCTION CAN NO LONGER BE CHANGED .
Change the PIN code 
Press the F button and enter the four-digit PIN code 
number within about 10 seconds. The ALARM indicator 
blinks red for a few seconds and a high-pitched 
confirmation sound is produced.  
Other settings
Reset the settings
Select “Factory default” in the Setting menu to reset the 
settings for the Antitheft alarm function.
1
2While the indicator is blinking, enter a new PIN code, 
then you will hear a high-pitched confirmation sound 
and the ALARM indicator is turned off.
When you enter an incorrect PIN code, you will hear 
a low-pitched sound. If you enter incorrect PIN code 
three times in a row, the alarm will start ringing. 
The PIN code for the Antitheft alarm function is a 
combination of 1, 2, or 3. Use the buttons 1, 2, and 3 to 
enter the PIN code. The default PIN code is “1111.”
✔Note:
  •   
This is effective only when the Antitheft alarm setting is 
released.
The Alarm operating configuration can be changed when 
the Antitheft alarm function is set to “Off.” See page 56 for 
setting or releasing this function.
Press the SELECT button at Alarm icon in the Setting Menu 
to display the Alarm setting dialog box. Use the Point 
ed 
buttons to select the desired option; use the Point 
7 8 
buttons to set the selected option.
Battery charge
  See the next page for details.
Alarm volume
  Small, Medium, Large (default)
Sensitivity
  Low  ..................... Less sensitive 
  Medium  ............. Normal sensitivity
  High  ................... Highly sensitive (default)
Ringing time
  10 seconds  ........ Rings about 10 seconds (default).
  60 seconds  ........ Rings about 60 seconds.
  Long time ........... Rings until the end of the battery life.
Alarm
Press the SELECT button at 
the Alarm icon to display the 
Alarm setting dialog box.
✔Note:
  • The Alarm icon appears dimmed and can 
be unavailable when the Antitheft alarm 
function is set to “On” or if the battery is not 
installed, discharged, or coming to the end 
of its life.
  • While the Alarm icon is selected, the 
Antitheft alarm setting buttons can be 
unavailable.
  • When selecting “Long time” option in the 
Ringing time, the duration of alarm sounding 
differs depending on the battery life.
Use the Point 7 8 
buttons to set the 
selected option.
Alarm operating configuration
Indicator
ALARM indicator
Terminal
F buttonButton 1, 2, 3 
						

							58
Charge the built-in battery pack
As long as the AC power cord is connected, the built-in 
battery for Alarm function is being charged at all times. 
While charging the battery, “Charging” is displayed in the 
menu. 
The “Charging” appears dimmed when the battery is fully 
charged or if charging malfunction occurs. ✔Note:
 •    The PIN code and settings you have changed are 
effective even after the battery is changed.
  • When replacing the rechargeable battery pack, protect 
the infrared remote receiver with a soft cloth to avoid 
damaging it.
  • Unplug the battery connector if you carry your 
projector frequently and use the carrying case. If you 
do not unplug the battery connector, the alarm may 
be triggered when the Alarm buttons are accidentally 
pressed inside the carrying case.
  •    The built-in battery pack is a consumable supply.  Each 
time you repeat discharge and recharge the battery, 
the battery life will decrease.  The battery will gradually 
discharge when left for long periods even without use.  
If the full-charged battery is left at normal temperature 
of 95º F (25º C), the battery will gradually discharge and 
can be non-rechargeable after about 7 months.  The 
battery life may vary from battery to battery according 
to the environment of use.
Remove the screw and 
open the battery cover.
Install the battery, then put back the battery cover 
and secure it with the screw.
Screw
Replace the rechargeable battery pack
Use only the specified battery for this projector. Using other 
types of battery may cause accident or fire hazard.
Replacement Battery:  SANYO Ni-MH BATTERY PACK
      Part No. 645 089 8587
How to replace the rechargeable battery pack
Unplug the AC power cord from a wall outlet.1
2Set the Alarm function to “Off” (see page 56). If it is 
not released, the alarm will start ringing when you try 
to remove the rechargeable battery cover.
Remove the screw from the rechargeable battery 
cover and open the cover.3
Pull out the battery connector and remove the battery.4
Install new battery and plug the connector into the 
socket. 
Note:  The battery connector has polarity. Observe 
battery polarity when installing.5
Put back the battery cover and secure it with the 
screw.
Caution:  Tighten the screw securely. If you fail to do 
so, the alarm will not operate. Do not use any 
other screws. This may cause damage to the 
projector.6
Antitheft Alarm Function 
						

							59
SAFETy PRECAUTIONS FOR SANy O Ni-MH BATTERy PACK
Observe the following precautions when handling the built-in battery pack of the projector:
 l  MAKE SURE THAT THE BATTERY PACK IS INSTALLED IN THE PROJECTOR WHEN RECHARGING. 
USING THE CHARGERS OTHER THAN THE PROJECTOR MAY CAUSE EXPLOSION OR A FIRE.
  l  The rechargeable battery pack is for use exclusively with this projector. Do not use in other products or 
this may cause accident.
  l  Do not throw the battery into fire or heat it. Doing so may cause an explosion or fire.
  l  Never attempt to disassemble, modify, reconstruct, or solder lead wires directly on to the battery.
  l  Do not drop or subject to strong forces. Doing so may cause the battery to leak fluid or explode.
  l  Do not expose to direct sunlight or high temperatures. This may degrade battery performance or cause 
leakage.
  l  Avoid contact with water or liquid. Exposure to water or liquid could result in battery corrosion or 
damage.
  l  Keep out of reach of children. They may accidentally swallow the battery. 
  l  Do not short-circuit battery terminals with metal objects. Do not store with metal objects or in a metal 
case.
  l  The rechargeable battery pack has a limited number of charge cycles and eventually need to be 
replaced. If it can no longer be recharged, stop charging immediately and replace it with new one.
  l  Recharge the battery in a place where the temperature is always between 32˚F to 104˚F (0˚C to 40˚C). 
Charging in the temperature out of this range may result in fluid leak, heat generation, or shortening 
battery life.
  l  If you do not use the projector or the Antitheft alarm function for a long period of time, remove the 
battery from the projector and store it in a place where the temperature is always between –4˚F to 86˚F 
(–20˚C to 30˚C).
  l  If a battery leaks and fluid comes in contact with skin, this may cause skin irritation. Flush the affected 
area thoroughly with water.
  l  If a battery leaks and fluid gets in contact with eyes, wash your eyes with water immediately and seek 
medical attention.
  l  Risk of an explosion if battery is replaced by an incorrect type.
  l  Dispose of used batteries according to the instructions or your local disposal rule and guidelines.
Antitheft Alarm Function 
						

							60
The WARNING indicator shows the state of the function which protects the projector. Check the state of the 
WARNING indicator and the POWER indicator to take proper maintenance. Indicators
Warning Indicator
The projector is shut down and the WARNING 
indicator is blinking red.
When the temperature inside the projector reaches a 
certain level, the projector is automatically shut down to 
avoid overheating. The POWER indicator is blinking while 
the projector is being cooled down. When the projector has 
cooled down enough (to its normal operating temperature), 
it can be turned on again by pressing the ON/STAND-BY 
button.  
✔Note:
• The WARNING indicator continues to blink even after the 
temperature inside the projector returns to normal. When 
the projector is turned on again, the WARNING indicator 
stops blinking. 
Then check the matters below:
–     Did you provide appropriate space for the projector to 
be ventilated? Check the installing condition to see if 
ventilation slots are not blocked.
–     Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the 
projector away from the duct or vent.
–     Are the air filters clean? Clean the air filters periodically. 
(p. 61) 
Indicators
The projector is shut down and the WARNING 
indicator lights red.
When the projector detects an abnormal condition, it 
is automatically shut down to protect the inside of the 
projector and the WARNING indicator lights red. In this 
case, unplug the AC power cord and plug it, and then 
turn on the projector once again to verify operation. If the 
projector cannot be turned on and the WARNING indicator 
lights red, unplug the AC power cord and contact the 
service station. 
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE 
AC POWER CORD CONNECTED UNDER AN 
ABNORMAL CONDITION. IT MAY RESULT IN FIRE 
OR ELECTRIC SHOCK.
Maintenance and Cleaning
WARNING
blinking red
WARNING
emit a red light