Sanyo Plc Xl51projector User Manual

							61
Maintenance and Cleaning
Turn off the projector, and unplug the AC power cord 
from the AC outlet.
Turn over the projector and remove the air filter by 
pulling the latches upward.
1
2
The air filter prevents dust from accumulating on the surface of the optical elements inside the projector. Should 
the air filter become clogged with dust particles, it will reduce coolin\
g fans’ effectiveness and may result in a 
buildup of internal heat and adversely affects the life of the projector. Clean the air filter by following the steps 
below.
Gently clean the filter by using a brush or blower.
3
Reinstall the filter into the projector properly.
4
CAUTION
Do not operate the projector with the air filter 
removed. Dust may accumulate on the optical 
elements degrading picture quality. Do not put 
anything into the air intake vents. Other wise it may 
result in malfunction of the projector.
RECOMMENDATION We recommend avoiding dusty/smoky environments when you operate the projector. Usage in these 
environments may cause poor image quality.
When you use the projector under dusty or smoky conditions, dust may accumulate on the lens, LCD panels, or 
optical elements inside the projector degrading the quality of a projected image.
When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning.
✔Note:
• When cleaning the air filter, protect the 
infrared remote receiver with a soft cloth to 
avoid damaging it.
•   If the filter is heavily clogged and unable to 
clean, replace it with a new one. Consult 
your dealer for details.
Replacement Filter Part No.: 610 335 4057
Air filter
Pull up and remove.
Cleaning the Air Filter
Clean up the dust on the projector and around the air 
vents.
5
WARNING: Do not wash the filter with water and 
any other liquid matter. Otherwise the filter may 
be damaged.
Be sure to reset the Filter counter after cleaning or replacing the filter. 
Press the MENU button to display the On-Screen 
Menu. Use the Point 
7 8 buttons to move the red 
frame pointer to the Setting Menu icon.
Use the Point ed buttons to move the red frame 
pointer to Filter counter and then press the SELECT 
button. A dialog box appears showing the total 
accumulated time of the filter use, a timer setting 
option, and the reset option. Select Reset and the 
“Filter counter Reset?” appears. Select [Yes] to 
continue.
1
2
Resetting the Filter Counter
Filter counter
Select Reset and 
the “Filter counter 
Reset?” appears.
Select [Yes], 
then another 
confirmation box 
appears.
Select [Yes] again 
to reset the Filter 
counter.Another confirmation dialog box appears, select [Yes] 
to reset the Filter counter.3
Reset the filter counter in the Setting Menu. See 
“Resetting the Filter Counter” below.6 
						

							62
CAUTION
This projector is equipped with a projection window.
Do not rub the projection window with a hard fiber cloth or hit it with a something hard to prevent the projection 
window from scratching. Do not use a chemical cleaner (liquid and solid) to avoid deteriorating the projection 
window.
Maintenance and Cleaning
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning 
cloth. When it is heavily soiled, use a small amount of 
mild detergent and finish with the cleaning cloth. Avoid 
excessive use of cleaner. Abrasive cleaners, solvents, or 
other harsh chemicals might scratch the surface of the 
cabinet.
When the projector is not in use, put the projector in an 
appropriate case to avoid dust and being scratched.
Cleaning the Projection Window
Unplug the AC power cord before cleaning.
First, remove the dust with a blower. Then gently wipe the 
projection window surface. Use a cleaning paper moistened 
with methyl alcohol (methanol). Avoid excessive use of 
cleaner.
Do not use abrasive cleaners, solvents, or other harsh 
chemical cleaners to avoid damaging the projection window. 
						

							63
Maintenance and Cleaning
When the projection lamp of the projector reaches its end of 
life, the Lamp replacement icon appears on the screen and 
LAMP REPLACE indicator lights yellow. Replace the lamp with 
a new one promptly. The timing when the LAMP REPLACE 
indicator should light is depending on the lamp mode.
Follow these steps to replace the lamp.
Lamp
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.  When ordering a projection lamp, give the following 
information to the dealer.
	l	 Model No. of your projector  :  PLC-XL51
	l  Replacement Lamp Type No. :  POA-LMP121 
                        (Service Parts No. 610 337 9937)
For continued safety, replace with a lamp of the 
same type. Do not drop a lamp or touch a glass 
bulb! The glass can shatter and may cause injury.Allow a projector to cool for at least 45 minutes 
before you open the Lamp cover. The inside of the 
projector can become very hot.
CAUTION
Screw
Turn off the projector and unplug the AC power cord. 
Let the projector cool for at least 45 minutes.
Loosen the two (2) screws that secure the lamp. Lift 
the lamp out of the projector by using the handle.
1
3
Replace the lamp with a new one and secure the two 
(2) screws. Make sure that the lamp is set properly. 
Close the lamp cover and secure the screw.4
2
Connect the AC power cord to the projector and turn 
on the projector.
6Reset the lamp counter.
See “Lamp Replacement Counter” on the next page.
5
Lamp Replacement
Handle
Screw
CAUTION
WARNING: 
TURN OFF  THE UV LAMP BEFORE 
OPENING  THE LAMP COVER Indicators
LAMP REPLACE 
indicator
Lamp replacement icon
✔Note:
  • The Lamp replacement icon will not appear when the 
Display function is set to “Off” (p.46), during “Freeze” 
(p.25), or “No show” (p.26).
✔Note:
  • When replacing the projection lamp, protect the infrared 
remote receiver with a soft cloth to avoid damaging it.
Lamp Cover
ScrewRemove the screw from the lamp cover and open the 
cover. 
						

							64
Maintenance and Cleaning
Be sure to reset the Lamp replacement counter after the lamp is replaced.  When the Lamp replacement 
counter is reset, the LAMP REPLACE indicator stops lighting.
Turn the projector on and press the MENU button 
to display the On-Screen Menu. Use the Point 
7 8 
buttons to move the red frame pointer to the Setting 
Menu icon.
Use the Point ed buttons to move the red frame  
pointer to Lamp counter and then press the SELECT 
button. The first dialog box appears showing the total 
accumulated lamp time and reset option. If you select 
Reset, “Lamp replacement counter Reset?” appears. 
Select “Yes” to continue.
1
2
Another confirmation dialog box appears, and select 
“Yes” to reset the Lamp replacement counter.3
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper handling 
may result in accidents, injury, or create a fire hazard.
l  Lamp life may differ from lamp to lamp and according to the environment of use. There is no guarantee 
of  the  same  life  for  each  lamp.  Some  lamps  may  fail  or  terminate  their  life  in  a  shorter  period  of  time 
than other similar lamps.
l
 If  the  projector  indicates  that  the  lamp  should  be  replaced,  i.e.,  if  the  LAMP  REPLACE  indicator  lights 
up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down. 
　  (Follow  carefully  the  instructions  in  the  Lamp  Replacement  section  of  this  manual.)  Continuous  use  of 
the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.  
l
 A  Lamp  may  explode  as  a  result  of  vibration,  shock,  or  degradation  as  a  result  of  hours  of  use,  as  it 
comes  to  the  end  of  life.  Risk  of  explosion  may  differ  according  to  the  environment  or  conditions  in 
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFET y PRECAUTIONS SHOULD BE TAKEN.
If  a  lamp  explodes,  disconnect  the  projector’s  AC  plug  from  the  AC  outlet  immediately.  Contact  an 
authorized  service  station  for  a  checkup  of  the  unit  and  replacement  of  the  lamp.  Additionally,  check 
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out 
from  the  cooling  air  circulation  holes.  Any  broken  shards  found  should  be  cleaned  up  carefully.  No  one 
should  check  the  inside  of  the  projector  except  those  who  are  authorized  trained  technicians  and  who 
are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those 
who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken 
glass.  
          LAMP HANDLING PRECAUTIONS
Lamp Replacement Counter
✔Note:
• Do not reset the Lamp replacement counter without 
implementing lamp replacement. Be sure to reset the 
Lamp replacement counter only after replacing the lamp.Select “Yes,” then 
another confirmation 
box appears.
Select “Yes” again to 
reset the lamp counter. To reset the lamp counter, 
move the pointer to Reset and 
then press the SELECT button. 
the “Lamp replacement 
counter Reset?” dialog box 
appears. 
						

							65
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
– Make sure you have properly connected the projector to peripheral equipment as described \
on pages 16-18.
–  Make sure all equipment is connected to the AC outlet and the power is turned on.
–  When you operate the projector with a computer and it does not project an imag\
e, restart the computer.
Appendix
Problem: – 
Solutions
No power
–  Plug the power cord of the projector into the AC outlet.
–  See if the POWER indicator lights red.
–    Wait  until  the  POWER  indicator  stops  blinking  to  turn  on  the  projector 
again. The projector can be turned on after the POWER indicator turns red. 
(see page 21).
–    Check  the  WARNING  indicator.  If  the  WARNING  indicator  lights  red,  the 
projector cannot be turned on (see on page 60).
–  Check the projection lamp (see page 63).
–  Check if the projector is installed in proper position. (See page 7)
–  Unlock the Key lock function for the projector. See page 51.
PIN code dialog box appears at 
start-up.–   PIN  code  lock  is  being  set.  Enter  a  PIN  code;  the “1234”  or  numbers  you 
have set (see pages 20, 52-53)
The initial display is not shown.–   Make  sure “Off  ”  or “Countdown  Off”  are  not  chosen  at  Display  function. 
(See “SETTING” section on page 46)
The initial display is not same with 
the default one.–  Make  sure “User”  or “Off”  are  not  chosen  at  Logo  select  function.　(See 
“SETTING” section on page 47)
Input signal switches automatically.  
(or does not switch automatically)–  Make sure Input search function is adjusted properly. See page 49.
When the projector is on and you 
press the input button, an icon other 
than the Lamp mode icon appears.
– That is the Filter warning icon. Refer to page 55.
An icon other than Input mode or 
Lamp mode icon appears.–   That  is  the  Lamp  replacement  icon  or  the  Filter  warning  icon.    See  page 
54.
No image
–    Check the connection between your computer or video equipment and the 
projector (see pages 16-18).
–    See if the input signal is correctly output from your computer. Some laptop 
computers  may  need  to  be  changed  the  setting  for  monitor  output  when 
connected to the projector. See your computer’s instruction manual for the 
setting.
–    It  t akes  about  30  seconds  to  display  an  image  after  turning  on  the 
projector.
–    See  if  the  selected  system  is  corresponding  with  your  computer  or  video 
equipment (see pages 28, 39).
–    Select correct input source once again through menu operation (see pages 
27, 37–38).
–    M a ke   s u r e   t h e   t e m p e r a tu r e   i s   n o t   o u t   o f   t h e   s p e c i f i e d   o p e r a t i n g 
temperature (41 ˚F–104 ˚F [5 ˚C–40 ˚C]).
–    When  "No  Show"  is  operating,  the  image  can  not  be  displayed.    Press  the 
NO SHOW button or any other button on the remote control. 
						

							66
Appendix
Image is out of focus.
– Adjust focus of the projector (see page 24).
–    Provide  proper  distance  between  the  projector  and  the  projection  screen 
(see page 14).
–    Check the projection window to see if it needs cleaning (see page 62).
–    Moving  the  projector  from  a  cool  to  warm  place  may  result  in  moisture 
condensation  on  the  projection  lens.  If  this  occurs,  leave  the  projector  off 
and wait until condensation evaporates.
–    Projecting  from  excessive  slant  angle  to  the  screen  may  cause  keystone 
distortion and partial imperfect focus.
Picture is not bright enough.
–   Check  if “Contrast”  or “Brightness”  are  adjusted  properly.  (See  page  34, 
42) 
–  Check if “Image level” is selected properly. (See pages 32-33, 40-41)
–  Check  the Lamp control function. ( See “SETTING” section on page 51)
–    Check  the  Lamp  replace  indicator.  If  it  lights,  the  end  of  lamp  life  is 
approaching. Replace the lamp with a new one promptly.  (See page 63)
The color is strange.
–   Check  the  Input  signal,  color  system,  video  system,  or  computer  system 
mode.
–  Adjust the Image Level properly.  See pages 32-33, 40-41.
Image is Left/Right reversed.
Image is Top/Bottom reversed–  Check the Ceiling/Rear function (see page 49).
–  Check the Ceiling function (see page 49).
The image is distorted or runs off.– Check “PC Adjustment” menu or “Screen” menu and adjust them.
No sound
– Check the audio cable connection from audio input source.
–  Adjust the audio source.
–  Press the Volume + button (see page 25).
–  Press the Mute button (see page 25).
–  Is  the  image  projected? You  will  hear  the  sound  only  when  the 
image is projected.
–
    When the AUDIO OUT is plugged in, the projector’s built-in speaker is not 
available.
Auto PC adjustment function does 
not work.–    Check  the  Input  signal.   Auto  PC Adjustment  function  can  not  work  when 
480p, 575p, 720p, 480i, 575i, 1035i, or 1080i is selected. (See page 29)
Some displays are not seen during 
the operation.– Check the Display function (see page 46).
The setting does not remain after 
turning off power.–   Make  sure  you  selected  “Store”  after  adjusting  settings.  Some  settings 
can not be stored if not registered with “Store”.
Power management function does 
not work.–   Power  management  function  can  not  work  while “Freeze”  or “No  Show” 
function is running.
Image disappears automatically.–   Check  the  power  management  function  in  the  Setting .  The  power 
management is set to "On" at the factory.
Capture function does not work.– Check the connection and input signal to see if there is signal. 
						

							67
Appendix
The CE Mark is a Directive 
conformity mark of the European 
Community (EC).
The Remote Control does not work.
– Check the batteries.
–    Make sure no obstruction is between the projector and the remote 
control.
–    Make sure you are not too far from the projector when using the remote 
control. Maximum operating range is 11.5’ (3.5 m).
–    Make sure the code of the remote control is conformed to that of the 
projector (see page 51).
–   Unlock the Key lock function for the remote control. (see page 51).
Indicators blinks or lights.
–    Check  the  status  of  the  projector  with  referring  to  “  INDICATORS  AND 
PROJECTOR CONDITION” on page 70.
–  For Alarm indicator, see pages 56-57.
Alarm does not stop ringing.
–   Connect  the  AC  power  cord  to  the  AC  outlet.  (Alarm  will  not  stop  ringing 
when  the  alarm  goes  off  while  trying  to  remove  the  rechargeable  battery 
cover.) See page 56-58.
Warning mode is not turned on.
–   If you cannot hear the bleeping sound when you press the Alarm buttons, 
you  are  not  pressing  the  buttons  correctly. Try  to  set  the  Alarm  setting 
again. See page 56.
Computer 2 cannot be selected.– Select Computer 2 in the Terminal function (see page 49).
The Terminal function cannot be 
selected.
–   The Terminal  function  cannot  be  selected  after  Computer  2  is  selected. 
S e l e c t   o t h e r   i n p u t   s o u r c e   s u ch   a s   C o m p u t e r   1   o r   Vi d e o   w i t h   t h e 
COMPUTER button or the VIDEO button on the remote control so that the 
Terminal function can be selected.  
appears on the screen
– Your operation is invalid. Operate correctly.
Unable to unlock the Logo PIN code 
lock, Security key lock or Security 
PIN code lock.–    Contact  the  dealer  where  you  purchased  the  projector  or  the  ser vice 
center.
WARNING :
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you purchased the 
projector or the service center. Specify the model number and explain about the problem. We will advise you 
how to obtain service.
Pixelworks ICs used.
This symbol on the nameplate means the product 
is Listed by Under writers Laboratories Inc. It is 
designed and manufactured to meet rigid U.L. 
safety standards against risk of fire, casualty and 
electrical hazards. 
						

							68
AppendixMenu Tree
Mode 1Mode 2SVGA 1 - - - -
Computer Input
✽Systems  displayed  in  the  System  Menu  var y 
depending on an input signal.
Computer Input/Video Input
Sound
Volume
Mute
Quit
On / Off
Sound0 - 63
Input
Computer 2
VideoAuto
Go to System (3)
Go to System (3)
Video 
Go to System (2) or (3)
Go to System (1)
Go to System (2)
S-Video
RGB( Scart )  
Quit
Quit
System (1)
RGBComputer 1
Component
Auto PC Adj.
Total dotsHorizontalVertical
Display area HDisplay area VReset
Dynamic
RealBlackboard (Green)
Image 1Image 2Image 3
Image AdjustContrastBrightnessColor temp.
Red
Gamma
Store
Quit
0 - 630 - 63
PC Adjust
Mode 1Mode 2Mode 3Mode 4Mode 5
Image Select
High
0 - 63
0 - 15
Image 1Image 2Image 3Image 4
Quit
Yes / No
ResetYes / No
Sharpness0 - 15
Image 4
Standard
Mode 1Mode 2Mode 3Mode 4Mode 5Quit
H-sync freq.V-sync freq.QuitClampCurrent mode
GreenBlue0 - 630 - 63
Store
Mode free
Quit
MidLowXLow
Quit
Adj.
Fine sync.0 - 31
NormalTrueWideFull 
Digital zoom +
Screen
Digital zoom –
Go to System (1)
Colorboard
Wired
Wireless
See owner’s manual “Network Setup and Operation.”
See owner’s manual “Network Setup and Operation.” 
						

							69
Appendix
AutoPALSECAMNTSCNTSC 4.43PAL-MPAL-N
Video Input
Auto1080i1035i720p575p480p575i480i
Dynamic
CinemaBlackboard (Green)
Image 1Image 2Image 3
Setting
Image Select
System (2)
System (3)
Image 4
LanguageSetting16 languages provided.
On / Off
Off/ Countdown off / On Logo select
On / OffOn / Off
Off
On / OffNormal / Auto / EcoCode 1 / Code 2
Keystone
Blue back
DisplayLogo
CeilingRear
Power management
On startLamp controlRemote control
Quit
ReadyShut down
Quit
Timer(1-30 Min)Quit
Factory default
L1 / L2Fan
Quit
Standard
Yes / No
Store / Reset
Quit
Off
UserCaptureYes / No
On / Off
Logo PIN code change
Logo PIN code lockLogo PIN code entry
Quit
PIN code lock entry
PIN code changeQuit
Default
ResetQuit
PIN code lock
Security
Quit
0 - 630 - 63
Off
Image AdjustContrastBrightnessColorTint
RedGreenBlueSharpness
ResetStore
Gamma
Progressive
0 - 630 - 630 - 630 - 15 0 - 15
Image 1Yes / No
Quit
Color temp.
OffNoise reductionL1L2
HighMidLowXLow
0 - 630 - 63
Image 2Image 3Image 4
L2L1
Adj.
Film
Lamp counterHour(s)
Off / On1 / On2 
Input searchAuto setup
NormalWide
Screen
Computer 2 /Monitor outTerminal
Colorboard
Uniformity Adj.Reset / Store 1 / Store 2
Alarm
SensitivityRinging timeQuit
Off
On
Alarm volumeSmall / Medium / LargeLow / Medium / High10seconds / 60seconds 
/ Long time
Battery ChargeCharging
Hour(s)Filter counter
Yes/NoOff/100H/200H/300HResetQuit
ZoomReset / Store 1 / Store 2 
OffProjectorRemote controlQuit
Key lock
Off / On1 / On2Auto PC adj.On / Off
Normal / EcoStandby mode
Off / On1 / On2  Fan controlWarning log
8 test patterns providedTest patternQuit 
						

							Indicators
Projector ConditionPOWERred/greenWARNING red
LAMP 
REPLACE
yellow
The projector is off. (The AC power cord is unplugged.)
The  projector  is  preparing  for  st and-by  or  the  projection  lamp  is 
being  cooled  down. The  projector  cannot  be  turned  on  until  cooling  is 
completed.
The projector is ready to be turned on with the ON/STAND-BY button.
The projector is operating normally.
The projector is in the Power management mode.
The  temperature  inside  the  projector  is  abnormally  high. The  projector 
cannot  be  turned  on. When  the  projector  is  cooled  down  enough  and 
the  temperature  returns  to  normal,  the  POWER  indicator  lights  red 
and  the  projector  can  be  turned  on.  (The  WARNING  indicator  keeps 
blinking.) Check and clean the air filters.
The  projector  has  been  cooled  down  enough  and  the  temperature 
returns  to  normal.  When  turning  on  the  projector,  the  WARNING 
indicator stops blinking. Check and clean the air filters.
The  projector  detects  an  abnormal  condition  and  cannot  be  turned  on. 
Unplug the AC power cord and plug it again to turn on the projector. If 
the projector is turned off again, unplug the AC power cord and contact 
the  dealer  or  the  service  center  for  service  and  checkup.  Do  not  leave 
the projector on. It may cause an electric shock or a fire hazard.
Appendix
Check the indicators for projector condition.  For Alarm indicator, see pages 56-57.
• • • green.• • • red• • • off
• • • blinks green.
✽		When the projection lamp reaches the end of its life, the LAMP REPLACE indicator lights yellow. 
When this indicator lights yellow, replace the projection lamp with a new one promptly. Reset the lamp 
replacement counter after replacing the lamp. See pages 63-64.
Indicators and Projector Condition
• • • blinks red.
✽
✽
✽
✽
✽
✽
✽
70