Samsung Idcs 500 General Description Manual

3.5SYSTEM TONES
TONEFREQUENCIES CADENCE
DIAL TONE 350 + 440 HzCONTINUOUS
RINGBACK TONE 440 + 480 Hz 1 sec on + 3 sec off
DID RINGBACK TONE 440 + 480 Hz 2 sec on + 4 sec off
BUSY TONE 480 + 620 Hz 0.5 sec on + 0.5 sec off
DND/NO MORE CALLS 480 + 620 Hz 0.25 sec on + 0.25 sec off
TRANSFER/CONF 350  +  440  Hz 0.1 sec on + 0.1 sec off
CONFIRMATION TONE 350 + 440 Hz 0.05 sec on + 0.05 sec off
ERROR TONE 480 + 620 Hz 0.05 sec of tone 1/0.05 sec of tone 2
SYSTEM TONES
Intercom Dial Tone—A steady tone that...

Transfer/Conference Tone—Indicates your call is being held and you can dial another party.
Confirmation Tone—Very short beeps followed by dial tone indicate you have correctly set or canceled a
system feature.
ERROR TONE—A distinctive two level beeping tone indicates you have done something incorrectly. Try
again.
TRANSFER/CONF TONE—100 ms ON/100 ms OFF
CONFIRMATION TONE—50 ms ON/50 ms OFF
ERROR TONE—50 ms of tone 1/50 ms of tone 2
CONTINUOUS
FOR TWO SECONDS
FOR TWO SECONDS
3.6KEYSET LED INDICATIONS...

3.7aRESERVE POWER DURATION ESTIMATES (in minutes)*
             UPS CAPACITY IN VOLT AMPS (VA)
250 450 600 900 1250 2000
1 5 20 30 47 75 180
2 8 10 24 40 70
3 5 7 203664
4 132235
5 101325
6 5 10 20
*These are approximate values. Specific UPS devices, due to their internal construction,
can have greater or lesser values.
3.7bRESERVE POWER DURATION ESTIMATES (in minutes)*
               BATTERY CAPACITY IN AH
40 80 120 160 200 240
1 20XXXXX
2 1020XXXX
3 7 13 20 X X X
4 5 10 15 20 X X
5 4 8 121620 X
6 3 7...

PART 4. BUSINESS FEATURE PACKAGE
SYSTEM FEATURES
Account Code Entry
Forced - Verified
Forced - Not Verified
Voluntary
Account Code Key (M Version)
Account Code Key - One Touch (L Version)
All Call Voice Page
Attention Tone
Authorization Codes
Forced
Voluntary
Auto Attendant†
Automatic Hold
Background Music
Cadence–Integrated Voice Mail
Call Activity Display
Call Costing
Caller Identification†
Automatic Number Identification (ANI)
Caller ID
Calling Line Identification (CLI)
Calling ID Features
Name/Number...

4.1 SYSTEM FEATURE DESCRIPTIONS
ACCOUNT CODE ENTRY
Station users may enter an account code (maximum 12 digits) before hanging up
from a call. This account code will appear in the SMDR printout for that call record.
Keyset users may enter this  code using an account code key without interrupting a
conversation. Single line telephone users must temporarily interrupt the call by
hook-flashing and dialing the feature access code. Manually entered account codes
can be up to 12 digits  long. In some cases...

codes. This option can be denied in system programming to prevent users from
bypassing the security of system account codes.
No Extender. When programmed without an extender the key will, when
pressed, prompt the user to enter the bin number the system account code table
where the account codes are stored.
ALL CALL VOICE PAGE
Users can page all internal and all external paging zones at the same time by
dialing the All Page code. Keysets may be restricted from making or receiving
pages in system...

ments or greetings. Twelve individual announcements (boxes), each with its own
dialing options, allow you to build call routing branches as needed. Callers are
routed through the branches by dialing extension numbers or single digits. This
system is compatible with Starmail and Cadence.
NOTE: Announcements recorded on one AA card can not be played to callers on
another AA card.
AUTOMATIC HOLD
While a keyset user is engaged on an outside (C.O.) call, pressing another trunk
key, route key or CALL button...

CALL COSTING
The iDCS 500 provides programmable call costing tables to calculate the cost of
incoming and outgoing calls. Rates are calculated by the number dialed, and may
include surcharges. Display keysets can be set to show the call duration timer or
the call cost. The SMDR report will show either the call duration or the call cost
depending on the station selection. One call handled by multiple callers will cost
each call segment separately.
CALLER IDENTIFICATION
The iDCS500 supports three methods...

CALLER ID FEATURES
The following features apply to all forms of Caller Identification, however, to make
them easier to read caller identification is referred to as Caller ID.
NAME/NUMBER DISPLAY
Each LCD keyset user can decide if he/she wants to see the name or number in the
display. Regardless of which one is selected to be seen first, the NND key is pressed
to view the other pieces of information.
NEXT CALL
In the event that you have a call waiting or a camped-on call at your keyset, you can
press the...