Panasonic Wifi Phone For Skype Kx Wp1050 Operating Instructions

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help201
Reset button
If you forget the user name and password for the base unit, press and hold the “FACTORY 
DEFAULT RESET” button on the bottom of the base unit with a pointed object until all the 
indicators go out. The settings are reset to default (see below). If necessary, set the 
settings again.
Note:
LYou need to register the handset to the base unit again when you reset the base unit to 
factory default.
See “Registering the handset” on page 133.
Default settings
Internet Connection Mode
Connection Mode DHCP
MTU size
– PPPoE 1492 bytes
– DHCP 1500 bytes
– Static 1500 bytes
FACTORY DEFAULT RESET button
WP1050.book  Page 201  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
202For assistance, please visit http://www.panasonic.com/help
Wireless Connection Settings
Advanced SetupWireless Mode 802.11b/g
Network  Name  (SSID) (Shown on the included Wireless LAN sticker)
SSID Broadcast Enable
WEP  key (Shown on the included Wireless LAN sticker)
Security Mode WEP
Key Index for Network Key (WEP) Key 1
MAC Address Filtering Disable
LAN
– IP Address 192.168.102.1
– Subnet Mask 255.255.255.0
DHCP Server
– DHCP Server Enable
– Starting IP Address 192.168.102.100
– Number of Lease IP Addresses 5 (One of which is assigned to the handset)
DMZ
– DMZ Disable
– DMZ Host IP Address (Blank)
Port Forwarding Unset 
UPnP Enable
Packet Filtering Unset
Easy Security
– Sends/Receives packets to/from IP 
addresses
Log OutputDeny
ON
– Stateful Packet Inspection
Log OutputEnable (Except Ident Packets)
ON
– Attack Detection
Log OutputDisable
OFF
Routing
– Static Routing Unset
WP1050.book  Page 202  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help203
Setting your computer
Obtaining an IP address automatically on your computer
When you cannot log in the base unit by using the computer you connected to the Ethernet 
(LAN) port on the base unit, check the Local Area Connection setting on the computer. It 
is necessary to obtain an IP address automatically from a DHCP server.
LYou must be logged in as an administrator in order to set the Local Area Connection.
1Click [Start], then click [Control Panel].
2Click [Network and Internet Connections], then click [Network Connections].
3Right-click the Local Area Connection icon connected to the base unit, then select 
[Properties].
4Select [Internet Protocol (TCP/IP)], then click [Properties].
WP1050.book  Page 203  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
204For assistance, please visit http://www.panasonic.com/help
5Select [Obtain an IP address automatically].
6Click [OK].
7Click [OK], then close the Network Connection window.
Setting the static IP address on your computer
When you log in the base unit with defective firmware, the firmware update screen will be 
displayed. In this case, a static IP address needs to be set on your computer.
1Click [Start], then click [Control Panel].
2Click [Network and Internet Connections], then click [Network Connections].
3Right-click the Local Area Connection icon connected to the base unit, then select 
[Properties].
WP1050.book  Page 204  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help205
4Select [Internet Protocol (TCP/IP)], then click [Properties].
5Select [Use the following IP address:].
WP1050.book  Page 205  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
206For assistance, please visit http://www.panasonic.com/help
6Enter the IP address.
LThe IP address must be within the range of 192.168.102.1 - 192.168.102.254 except 
for 192.168.102.1 (the default IP address of the base unit on the LAN side).
7For Subnet mask, enter 255.255.255.0.
8Click [OK].
9Click [OK], then close the Network Connection window.
WP1050.book  Page 206  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help207
Changing the proxy server settings on Web browser
If your Internet service provider uses the proxy server, you cannot log in the base unit. 
Change the proxy server settings on your Web browser.
1Open your Web browser. (The below example is Internet Explorer 6.0.)
2Click [Tools], then select [Internet Options...].
3Click [Connections] tab, then click [LAN Settings…].
WP1050.book  Page 207  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
208For assistance, please visit http://www.panasonic.com/help
4See if the “Use a proxy server for your LAN” check box is checked or not.
NIf checked, click [Advanced…] and go to step 5.
NIf not checked, click [Cancel] then close the Internet Options window. Proxy server 
settings are not required.
5Enter the base unit’s IP address into the “Do not use proxy server for addresses 
beginning with:” data field.
6Click [OK].
7Click [OK], then close the Internet Options window.
192.168.102.1
WP1050.book  Page 208  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help209
Note:
LIn step 5, enter the handset’s IP address into the “Do not use proxy server for addresses 
beginning with:” data field when you update the firmware of the handset.
Setting UPnP to display the shortcut
To display the KX-WPA102 shortcut in the My Network Places folder, Windows 
components should be added. Enable UPnP (Universal Plug and Play) following the steps 
below.
1Click [Start], then click [Control Panel].
2Click [Add or Remove Programs], then click [Add/Remove Windows 
Components].
3Select [Networking Services], then click [Details…].
4Check [Universal Plug and Play], then click [OK].
5Click [Next>].
Note:
LIf you are using Windows XP Service Pack 2, check [Internet Gateway Device 
Discovery and Control Client] and [UPnP User Interface] in step 4.
LThis feature is only available when using Windows XP.
Using your computer on a wireless LAN
The 15 character device-specific network name (SSID) and 13 alphanumeric character 
128 bit encryption network key (WEP) are set as factory defaults. These factory default 
setting values are shown on the included Wireless LAN sticker. If you use your computer 
on a wireless LAN, use the values on the sticker to set the wireless LAN configuration on 
your computer. To set your computer to be used on a wireless LAN, see the manual for the 
computer you use.
Note:
LTo use your computer on a wireless LAN, a wireless LAN card needs to be installed on 
your computer.
WP1050.book  Page 209  Wednesday, November 22, 2006  9:24 AM 
						

							Useful Information
210For assistance, please visit http://www.panasonic.com/help
Additional accessories
Sales and support information
LTo order additional accessories, call 1-800-332-5368.
LTTY users (hearing or speech impaired users) can call 1-866-605-1277.
Headset (optional)
Connecting a headset to the handset allows hands-free phone conversations. We 
recommend using the Panasonic headset shown below.
LThe headset model numbers compatible with the handset:
KX-TCA88HA
KX-TCA86
KX-TCA91
KX-TCA92
KX-TCA93
KX-TCA94
KX-TCA95
WP1050.book  Page 210  Wednesday, November 22, 2006  9:24 AM