Panasonic Wifi Phone For Skype Kx Wp1050 Operating Instructions

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help151
3Configure the settings, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
SettingDescription
[MAC Address Clone]LSelect whether to enable or disable the MAC address 
clone feature.
[Original MAC Address]LBase unit’s MAC address is displayed.
[Cloned MAC Address]LEnter MAC address to be cloned.
LSet 12 hexadecimal characters, with separation by 
colon (:) of every 2 digits (e.g. “12:34:56:78:9F:0A”).
WP1050.book  Page 151  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
152For assistance, please visit http://www.panasonic.com/help
Advanced settings
LAN/DHCP Server:
This feature allows you to configure the local network settings and DHCP server settings.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [LAN/DHCP Server].
Note:
LThis feature is not available in AP (Bridge) mode.
WP1050.book  Page 152  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help153
3Configure the settings, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LIf you change the LAN network settings or DHCP server settings, the entries in the Static 
DHCP table will be deleted.
LIn step 4, if the LAN side setting is changed, you need to change your computer’s setting 
and click the link shown on the Restarting page.
SettingDescription
[IP Address]LEnter the IP address and subnet mask corresponding to your 
local network.
LSet 4 numbers (0 – 255) separated by periods such as 
“192.168.0.253”.
Note:
LThere are some restrictions on IP address entry. For 
example, “0.0.0.0” and “255.255.255.255” are not available. [Subnet Mask]
[DHCP Server]LThis setting assigns IP addresses to devices on your LAN. 
Select whether to enable or disable this feature.
[Starting IP 
Address]LEnter the starting IP address for the DHCP server’s IP 
assignment.
[Number of 
Leased IP 
Address]LEnter the number of the leased IP addresses (maximum: 5). 
The first IP address is assigned to the handset. The 
subsequent ones are assigned to computers.
WP1050.book  Page 153  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
154For assistance, please visit http://www.panasonic.com/help
Static DHCP (IP Address Reservation):
The Static DHCP function allows you to stabilize the IP address assigned to the computer 
by registering the computer’s MAC address. Up to 5 entries can be registered. The first 
entry is reserved for the handset.
1Click [Add] under the Static DHCP (IP Address Reservation) heading in LAN/DHCP 
Server page (page 152), then configure the settings.
LYou can also select the setting from the DHCP Server Lease Table. Click [Add] in the 
“Operation” column under the Setting From DHCP Server Lease Table heading.
LWhen you click [Refresh], the network connection status is refreshed.
2Click [Add] under the Manual Setting heading.
3Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
SettingDescription
[MAC Address]LEnter the LAN card’s MAC address for the corresponding 
computer.
LSet 12 hexadecimal characters, with separation by colon(:) of 
every 2 digits (e.g.12:34:56:78:9F:0A).
[IP Address]LEnter the IP address that you want to stabilize for the 
corresponding computer.
WP1050.book  Page 154  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help155
Note:
LTo edit the settings:
1Click the desired entry number under the static DHCP setting, click the desired entry 
number under the Static DHCP (IP Address Reservation) heading in LAN/DHCP 
Server page (page 152).
2Edit the items in the Static DHCP Setting page.
3Click [Save].
4Click [Restart].
LTo delete the settings:
1Click the desired entry number under the static DHCP setting, click the desired entry 
number under the Static DHCP (IP Address Reservation) heading in LAN/DHCP 
Server page (page 152).
2Click [Delete] in the Static DHCP Setting page.
3Click [OK] in the confirmation dialog box.
4Click [Restart].
Port Forwarding:
This feature allows you to configure the port forwarding settings. Enabling Port Forwarding 
allows other Internet users to access services running on your LAN.
Up to 10 settings can be stored.
Important:
LWhen setting up the port forwarding feature, there is a possibility of illegal access to the 
forwarding port from the Internet. For safety reasons, set this feature only when 
required.
1Click [Advanced Setup] on the Top Menu.
WP1050.book  Page 155  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
156For assistance, please visit http://www.panasonic.com/help
2Click the [Advanced] tab, then click [Port Forwarding]. 
3To add a new entry, click [Add] under the Port Forwarding Table heading.
WP1050.book  Page 156  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help157
4Configure the settings under the Port Forwarding Setting heading. Click [Add] to add 
a new entry.
5Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LTo edit the setting:
1Click the desired entry number in step 3.
2Edit the items in the Port Forwarding Setting page.
3Click [Save].
4Click [Restart].
LTo delete the setting:
1Click the desired entry number in step 3.
2Click [Delete] in the Port Forwarding Setting page.
3Click [OK] in the confirmation dialog box.
4Click [Restart].
SettingDescription
[No.]LSelect the desired entry number for the port forwarding 
setting.
LEntry number represents the priority. Entry number 1 has the 
highest priority.
[Status/Port 
Forwarding]LSelect whether to enable or disable the port forwarding 
feature.
[Forwarding IP 
Address]LEnter the IP address of the computer that is hosting the 
service.
LThe device registered as the forwarding IP address can be 
accessed from the Internet through the registered protocol 
and port.
[Protocol]LSelect the desired protocol used to access your hosting 
service from TCP/UDP/TCP&UDP/ESP/GRE.
[Port]LEnter the forwarding port number when you select the 
protocol from TCP/UDP/TCP&UDP.
LIf you want to set one port, enter its port number only.
LIf you want to set a range of ports, enter the port numbers in 
the following way: “2000 – 3000”
WP1050.book  Page 157  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
158For assistance, please visit http://www.panasonic.com/help
LThis feature is not available in AP (Bridge) mode.
DMZ:
This feature allows you to configure the DMZ (DeMilitarized Zone) settings. Enable DMZ 
to expose a specified computer on your LAN to the Internet.
Important:
LA computer specified as the DMZ host may be vulnerable to security risks.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [DMZ].
3Configure the settings, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LThis feature is not available in AP (Bridge) mode.
SettingDescription
[DMZ]LSelect whether to enable or disable the DMZ feature.
[DMZ Host IP 
Address]LEnter the IP address of the computer to be exposed to the 
Internet.
WP1050.book  Page 158  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help159
UPnP:
This feature allows you to configure the UPnP (Universal Plug and Play) settings. 
Enabling UPnP allows the base unit to be compliant with the UPnP standard.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [UPnP].
3Select the desired setting, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LThis feature is enabled in AP (Bridge) mode automatically.
SettingDescription
[UPnP]LSelect whether to enable or disable the UPnP feature.
WP1050.book  Page 159  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
160For assistance, please visit http://www.panasonic.com/help
Easy Security:
This feature allows you to easily set up packet filtering.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [Easy Security].
WP1050.book  Page 160  Wednesday, November 22, 2006  9:24 AM