Panasonic Wifi Phone For Skype Kx Wp1050 Operating Instructions

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help161
3Configure the settings, then click [Save].
LCheck the box in the Log Output column to create a log of each action.
LIf you select [Enable] and check “Log Output”, the log will be output. If you select 
[Disable], the log will not be output even if you check “Log Output”.
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LThis feature is not available in AP (Bridge) mode.
SettingDescription
[Transmission/
reception of 
Packets with 
private IP 
addresses via 
WAN interface]LSelect whether to deny or allow packets to be sent or 
received when the source of an incoming (from WAN) packet 
and the destination of an outgoing (to WAN) packet are 
private IP addresses. This feature is valid when the WAN IP 
address is global. The default is set to Deny. 
LCheck whether output or not this log. The default is set to ON.
[Stateful Packet 
Inspection]LSelect whether to enable or disable the stateful packet 
inspection feature.
LSome E-mail servers authenticate clients using identification 
packets which use TCP port 113. If the E-mail feature does 
not work well, select [Enable (Except Ident Packets)], 
which is the default setting for this feature.
LCheck whether output or not this log. The default is set to ON.
[Attack Detection]LSelect whether to enable or disable the attack detection 
feature. The default is set to Disable.
LThe following type of attacks can be detected:
–TCP Scan
–UDP Scan
– ICMP Echo
LCheck whether output or not this log. The default is set to 
OFF.
WP1050.book  Page 161  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
162For assistance, please visit http://www.panasonic.com/help
Packet Filtering:
This feature allows you to configure the packet filtering settings, and to control the packets 
to be received/transmitted between the Internet and the computers on your LAN.
Up to 20 settings can be registered.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [Packet Filtering].
WP1050.book  Page 162  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help163
3To add a new entry, click [Add] under the Packet Filtering Table heading.
WP1050.book  Page 163  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
164For assistance, please visit http://www.panasonic.com/help
4Configure the settings under the Packet Filtering Setting heading, then click [Add] to 
add the new entry.
SettingDescription
[No.]LSelect the desired entry number for the packet filtering 
setting. Entry number represents the priority. Entry number 1 
has the highest priority.
[Status/Packet 
Filtering]LSelect whether to enable or disable the packet filtering 
feature.
[Action]LSelect whether to allow or deny IP packets that are being 
received.
[Direction]LSelect [LiW] (filtering when sending to WAN) or [WiL] 
(filtering when receiving from WAN).
[Source IP 
Address]LEnter the packet source IP address/netmask to be filtered.
LIf you want to set one IP address, enter that IP address in IP 
address field and “32” in netmask field. (e.g. If you want to 
control the packet from 192.168.102.10, enter 
“192.168.102.10” in IP address field and “32” in netmask 
field.)
LIf you want to set a range of IP addresses, enter that network 
address in IP address field and it’s netmask in netmask field. 
(e.g. If you want to control the packet from 192.168.102.0 - 
192.168.102.255, enter “192.168.102.0” in IP address field 
and “24” in netmask field.)
LIf you want to set the base unit’s address, enter “local” in IP 
address field. Leave the netmask field blank.
*1
LIf you want to set all IP address, select “*” in IP address field. 
Leave the netmask field blank.
[Source Port]LEnter the packet source port to be filtered when you select 
the protocol from TCP/UDP/TCP&UDP.
LIf you want to set one port, enter its port number only.
LIf you want to set a range of ports, enter the port numbers in 
the following way: “2000 – 3000”
LIf you want to set all ports, select “*”.
[Destination IP 
Address]LEnter the packet destination IP address to be filtered.
LThe entry is the same as the Source IP Address.
WP1050.book  Page 164  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help165
*1 When direction is WiL, Source IP ‘local’ is Invalid. When direction is LiW,  
Destination IP ‘local’ is invalid.
5Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Important:
LThe packet filtering is NOT executed for the DMZ host.
Note:
LTo edit the setting:
1Click the desired entry number in step 3. 
2Edit the items in the Packet Filtering Setting page.
3Click [Save]. 
4Click [Restart].
LTo delete the setting:
1Click the desired entry number in step 3. 
2Click [Delete] in the Packet Filtering Setting page.
3Click [OK] in the confirmation dialog box.
4Click [Restart].
LAs the default security policy, outgoing packets initiated from the computer on your LAN 
to the Internet are allowed, but other packets are denied.
LSecurity functions are executed in the following order:
– Easy security (Attack detection)
– Packet filtering
– Easy security (except for Attack detection)
LThis feature is not available in AP (Bridge) mode.[Destination Port]LEnter the packet destination IP address/netmask to be 
filtered.
LThe entry is the same as the Source Port.
[Protocol]LSelect the protocol to be used from TCP/UDP/TCP&UDP/
ESP/GRE/ICMP. If you want to set all protocols, select “*”.
[Log Output]LSet whether to display the temporarily saved packet 
information on the “Packet Filtering Log:” (page 190).
SettingDescription
WP1050.book  Page 165  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
166For assistance, please visit http://www.panasonic.com/help
Routing:
This feature allows you to set static routing between the base unit and another network. 
Use this feature when you have several local networks. Up to 4 settings can be registered.
1Click [Advanced Setup] on the Top Menu.
2Click the [Advanced] tab, then click [Routing].
3To add a new entry, click [Add] under the Static Routing Table heading.
WP1050.book  Page 166  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help167
4Configure the settings under the Routing Setting heading, then click [Add] to add a new 
entry.
5Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LTo edit the setting:
1Click the desired entry number in step 3.
2Edit the items in the Routing Setting page.
3Click [Save].
4Click [Restart].
LTo delete the setting:
1Click the desired entry number in step 3.
2Click [Delete] in the Routing Setting page.
3Click [OK] in the confirmation dialog box.
4Click [Restart].
LThis feature is not available in AP (Bridge) mode.
SettingDescription
[Status]LSelect whether to enable or disable the routing setting.
[Destination 
Network/Mask]LEnter the network address/netmask for the destination IP 
address.
LIf you want to set one IP address, enter that IP address in IP 
address field and “32” in netmask field. (e.g. If you want to 
control the packet from 192.168.1.1, enter “192.168.1.1” in IP 
address field and “32” in netmask field.)
LIf you want to set a range of IP addresses, enter that network 
address in IP address field and it’s netmask in netmask field. 
(e.g. If you want to control the packet from 192.168.1.0 - 
192.168.1.255, enter “192.168.1.0” in IP address field and 
“24” in netmask field.)
[Gateway]LEnter the gateway IP address.
WP1050.book  Page 167  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
168For assistance, please visit http://www.panasonic.com/help
Wireless
Wireless Basic:
This feature allows you to set the wireless mode and network name (SSID: Service Set 
IDentifier).
1Click [Advanced Setup] on the Top Menu.
2Click the [Wireless] tab, then click [Wireless Basic].
WP1050.book  Page 168  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help169
3Configure the settings, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note: 
LYou need to register the handset to the base unit again when you change the network 
name (SSID). See “Registering the handset” on page 133.
SettingDescription
[Mode]LSelect your wireless network mode from the pull-down menu.
LIf you have both 802.11b and 802.11g wireless devices in 
your network, select [802.11b/g].
LIf you have only 802.11b wireless devices, select [802.11b]
[Channel]LSelect [Auto] or the desired channel from 1 to 11.
[Network Name 
(SSID)]LEnter your wireless network name (SSID) (1 – 32 
alphanumeric characters) in this data field.
[SSID Broadcast]LEnable or disable the setting to broadcast your SSID.
LIf you select [Disable], only wireless devices that know the 
SSID of the base unit can connect to the base unit.
LIf you select [Enable], any wireless device can detect the 
SSID of the base unit.
WP1050.book  Page 169  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
170For assistance, please visit http://www.panasonic.com/help
Wireless Security:
This feature allows you to set security measures for connecting to wireless LAN.
1Click [Advanced Setup] on the Top Menu.
2Click the [Wireless] tab, then click [Wireless Security].
WP1050.book  Page 170  Wednesday, November 22, 2006  9:24 AM