Panasonic Wifi Phone For Skype Kx Wp1050 Operating Instructions

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help191
UPnP Port Mapping Log:
This feature displays the temporarily saved logs of port mapping additions, deletions and 
failures. It also saves the logs to your computer. This feature is enabled when [UPnP] 
(page 159) is set to “Enable”.
1Click [Advanced Setup] on the Top Menu.
2Click the [Maintenance] tab, then click [UPnP Port Mapping Log].
LUPnP port mapping logs are displayed.
3Click [Save].
4Specify the location and enter the file name, then click [Save] in the Save As dialog 
box.
Note:
LThe log stores up to 20 most recent events.
WP1050.book  Page 191  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
192For assistance, please visit http://www.panasonic.com/help
Connection Log:
This feature displays the temporarily saved Internet connection logs, such as 
disconnection and authentication logs for PPPoE and DHCP connections. It also saves 
the logs to your computer.
1Click [Advanced Setup] on the Top Menu.
2Click the [Maintenance] tab, then click [Connection Log].
LConnection logs are displayed.
3Click [Save].
4Specify the location and enter the file name, then click [Save] in the Save As dialog 
box.
Note:
LThe log stores up to 20 most recent events.
WP1050.book  Page 192  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help193
Support
Help:
The Help page describes the features of each of the following:
1. Initial Setup
2. Top Menu
3. Network Connection
4. Update Firmware
5. Advanced Setup
Basic
Advanced
Wireless
Sta tus
Maintenance
Support
6. Handset Information
7. Temporary LAN Side Network Setting
1Click [Advanced Setup] on the Top Menu.
2Click the [Support] tab, then click [Help].
3Click [View].
4Click the desired item to view its help page.
Note:
LYou can also view help by clicking [Help] on each setup page.
WP1050.book  Page 193  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
194For assistance, please visit http://www.panasonic.com/help
Support Link:
This feature allows you to get product and support information from the Internet.
1Click [Advanced Setup] on the Top Menu.
2Click the [Support] tab, then click [Support Link].
3Click the URL.
WP1050.book  Page 194  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help195
Handset Information
This feature displays the registered handset’s wireless connection status to the base unit. 
It also displays the handset’s MAC address and IP address when connected to the base 
unit.
1Click [Handset Information] on the Top Menu.
LThe handset status is displayed when the wireless connection between the 
registered handset and the base unit is established.
Note:
LIt may take a while to display the screen.
WP1050.book  Page 195  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
196For assistance, please visit http://www.panasonic.com/help
Temporary LAN Side Network Setting when networks 
on the WAN side and the LAN side overlap
When networks on the WAN side and the LAN side overlap, the connection to the WAN 
side of the base unit is terminated. In this case, you are required to change the LAN side 
settings from the current LAN side settings (default IP address: 192.168.102.1, default 
subnet mask: 255.255.255.0).
If the unit detects a network overlapping, the Temporary LAN Side Network Setting page 
is displayed.
You can change the LAN side settings temporarily with the following steps:
LWAN Indicator on the base unit alternately flashes between in Amber and Green in turn. 
This state represents that the connection to the WAN side of the base unit is terminated.
WP1050.book  Page 196  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help197
LIP address and Subnet Mask under the WAN heading show the current WAN side 
settings of the base unit.
LIP address, Subnet mask and Starting IP address (DHCP Server) under the LAN 
(settings) heading show the current LAN side settings of the base unit.
1Enter IP address, Subnet Mask and Starting IP address (DHCP Server) under the LAN 
(temporary) heading.
LSee also the Help on the LAN (temporary) heading for data entry.
2Click [Apply]. 
LThe restarting page is displayed when the entered IP address, Subnet mask and 
Starting IP address (DHCP Server) are correct. 
SettingDescription
[IP Address]LEnter the IP address and subnet mask corresponding to your 
temporary local network. 
LSet the third number (0 – 255) separated by periods different 
from that of the WAN, such as “192.168.101.1”
Note:
LThere are some restrictions on IP address entry. For 
example, “0.0.0.0” and “255.255.255.255” are not available. [Subnet Mask] 
[Static IP Address 
(DHCP Server)]LEnter the starting IP address for the DHCP server’s IP 
assignment. 
LSet the third number (0 – 255) separated by periods same as 
that of the LAN (temporary) you set above, such as 
“192.168.101.100”
WP1050.book  Page 197  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
198For assistance, please visit http://www.panasonic.com/help
3Change the network setting on your computer. 
LIf DHCP is enabled for obtaining IP address on your computer, you need to obtain IP 
address again.
LIf Static IP address is entered on your computer, you need to change IP address and 
subnet mask on your computer manually. See “Setting the static IP address on your 
computer” (page 204).
LOther operations may be possible for recovering the Network setting on your 
computer.
4Click the IP address shown on the restarting page.
LThe Top Menu is displayed.
LWAN Indicator flashes as a short blinking in Amber and a long flash in Green in turn. 
This state indicates that the connection to the WAN side of the base unit has been 
recovered for the Internet connection. During this state, Port Forwarding, DMZ, 
Packet Filtering and Static Routing functions are disabled.
Note: 
LIn step 2, Configuration Error message is displayed if network still overlaps or your data 
entry is not correct. You need to try to enter the IP address, Subnet mask and Starting 
IP address (DHCP Server) again. See also the Help on the LAN (temporary) heading for 
data entry. 
LThe IP address, Subnet mask and Starting IP address (DHCP Server) entered in the 
Temporary setting are effective while the base unit is turned on, and will be cleared away 
from the unit when the base unit is turned off.
LIf you want to change the LAN side settings permanently, click [Top Page] button on the 
right top of the Temporary LAN Side Network Setting page and change the LAN side 
settings from [Advanced Setup]. 
WP1050.book  Page 198  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help199
Downloading the version-up firmware to your 
computer for recovering the base unit
When the WAN Indicator is flashing in amber, the firmware of the base unit is defective and 
the base unit is operating in recovery mode.
Before downloading the firmware for the base unit, you need to set the static IP address 
on your computer. For setting the static IP address on your computer, see page 204.
On your computer:
1On the Web browser, enter http://192.168.102.1
On the base unit:
2Specify the file name.
You can also click [Browse...] to select the desired file name from the list.
3Click [Start].
LThe base unit automatically restarts after the firmware is updated.
Important:
LDo not interrupt the firmware updating process by cutting the power supply until the 
progress indicator reaches 100% and the base unit restarts itself.
4Confirm the WAN Indicator is not flashing in amber, then set your computer settings 
back to the previous conditions.
WP1050.book  Page 199  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
200For assistance, please visit http://www.panasonic.com/help
Mode selector
Once you have created a new profile in the Initialization Setup (page 36), or added/edited 
profiles (page 136, 147) in the base unit settings, you do not need to log in the base unit 
each time. You only need to slide the Mode selector switch to “HOME” or “HOTEL” mode 
so that the base unit can connect to the Internet in the connection mode that is pre-
registered for either “HOME” or “HOTEL” mode. You need to switch the Mode selector 
before turning on the base unit.
Mode selector
WP1050.book  Page 200  Wednesday, November 22, 2006  9:24 AM