Panasonic Wifi Phone For Skype Kx Wp1050 Operating Instructions

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help171
3Configure the settings, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
SettingDescription
[Security Mode]LSelect the desired security mode.
LNo Encryption (Open), WEP, WPA-PSK and WPA2-PSK are 
available for the wireless devices, including the handset. 
Select the desired security mode for your wireless devices 
connected to the base unit. Default is set to WEP.
WEP settings
[Network Key]For WEP 64bit:
LEnter the network key containing 5 alphanumeric characters 
or 10 hexadecimal characters.
For WEP 128bit:
LEnter the network key containing 13 alphanumeric 
characters or 26 hexadecimal characters.
LPress [View] to display the network key.
[Key Index]LSelect [Key 1], [Key 2], [Key 3] or [Key 4] to be used if you 
use WEP. The default is set to [Key 1].
WPA-PSK/WPA2-PSK Settings
[Network Key]LEnter the network key (8 – 63 alphanumeric characters) in 
this data field.
LPress [View] to display the network key.
[Data Encryption]LSelect the desired data encryption method.
For WPA-PSK
LIf your wireless devices use TKIP, select [TKIP] or 
[TKIP+AES].
LIf your wireless devices use AES, select [TKIP+AES].
For WPA2-PSK
LIf your wireless devices use TKIP, select [TKIP+AES].
LIf your wireless devices use AES, select [AES] or 
[TKIP+AES].
[Session-Key 
renewal interval]LSet the interval for refreshing the encryption key between 30 
and 604800 seconds. 604800 seconds is the equivalent of 
one week. The default is set to 1800.
WP1050.book  Page 171  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
172For assistance, please visit http://www.panasonic.com/help
Note:
LYou need to register the handset to the base unit again when you change the security 
mode, the network key and/or the key index.
See “Registering the handset” on page 133.
LWhen you use WEP for the network key, set either the Network Key No. 1, No. 2, No. 3 
or No. 4 as a key index according to the setting of the wireless LAN card you use. When 
you do not use WEP, you are suggested to use WPA-PSK/WPA2-PSK as the security 
mode.
MAC Address Filtering:
This feature allows you to configure the MAC address filtering settings so that devices 
without the particular MAC address will be filtered.
MAC address filtering is available only for wireless devices. Up to 5 entries can be 
registered. The first entry is reserved for the handset.
To enable or disable MAC address filtering feature: 
1Click [Advanced Setup] on the Top Menu.
2Click the [Wireless] tab, then click [MAC Address Filtering].
WP1050.book  Page 172  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help173
3Configure the setting, then click [Save].
4Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
To configure MAC address filtering entry:
1Click [Advanced Setup] on the Top Menu.
2Click the [Wireless] tab, and then click [MAC Address Filtering].
3To add a new entry, click [Add] under the MAC Address Filtering Table heading.
LMAC Address Filtering Setting page is displayed.
SettingDescription
[MAC Address 
Filtering]LSelect whether to enable or disable the MAC address filtering 
feature.
LIf the MAC address filtering is enabled, only the wireless 
device with the registered MAC address can send/receive 
data.
WP1050.book  Page 173  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
174For assistance, please visit http://www.panasonic.com/help
4Configure the setting, and then click [Add].
5Click [Restart].
LThe base unit automatically restarts and the Top Menu is displayed.
Note:
LTo edit the setting:
1Click the desired entry number.
2Edit the items in the MAC Address Filtering Setting page.
3Click [Save].
4Click [Restart].
LTo delete the setting:
1Click the desired entry number.
2Click [Delete] in the MAC Address Filtering Setting page.
3Click [OK] in the confirmation dialog box.
4Click [Restart].
LThe registered handset is automatically listed in the MAC Address Filtering Table.
SettingDescription
[MAC Address]LEnter the desired MAC address.
LSet 12 hexadecimal characters, with separation by colon (:) 
of every 2 digits (e.g. “12:34:56:78:9F:0A”).
WP1050.book  Page 174  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help175
Status
The status pages allow you to view the status of the base unit.
The information displayed on the pages are useful when contacting an authorized 
servicenter.
1Click [Advanced Setup] on the Top Menu.
2Click the [Status] tab, then click the desired item on the left.
[Network Status] shows the WAN/LAN interface status and routing/ARP tables.
123
45
6
7
8
9
jkl
m
n
WP1050.book  Page 175  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
176For assistance, please visit http://www.panasonic.com/help
WAN Interface Status:
1MAC Address: Show the MAC address of the WAN port.
2Connection Mode: Show the Internet connection mode. (DHCP/
PPPoE/AP/Static)
3Connection Status: Show whether the WAN port is connecting to the 
Internet or not.
4IP Address: Show the IP address of the WAN port.
5Subnet Mask: Show the subnet mask of the WAN port.
6Default Gateway: Show the IP address of the default gateway.
7MTU: Show the current MTU value.
8Lease Time: Show DHCP refresh interval time (in second) 
assigned by the DHCP server of the WAN side. 
This is available in DHCP only.
9DHCP Server: Show the IP address of DHCP server of the WAN 
side. This is available in DHCP only.
LAN Interface Status:
jMAC Address: Show the MAC address of the LAN port.
kIP Address: Show the IP address of the LAN port.
lSubnet Mask: Show the subnet mask of the LAN port.
Routing Table:
mRouting Table: Routing table shows the routing.
ARP Table:
nARP Table: ARP (Address Resolution Protocol) table shows 
the list of the hosts that are reached directly from 
the base unit. Combinations of IP address and 
MAC address of each host are shown.
WP1050.book  Page 176  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help177
[DHCP Lease Table] shows the DHCP server status and lease table.
DHCP Server Status:
1DHCP  Server: Show whether the DHCP server feature is enabled 
or not.
2DNS Server: Show the IP address of the DNS server.
3Domain Name: Show the domain name of the local network.
4Lease Time(s): Show DHCP refresh interval time (in second) 
assigned for the DHCP clients connected to the 
local network.
5Lease Address: Show the IP address range that can be assigned 
for the DHCP clients.
DHCP Lease Table:
6DHCP Lease Table: Show the list of DHCP client hosts. Combinations 
of the IP address and MAC address are shown. 
Expire Time is shown in seconds. Type shows 
Auto or Static.
1
2
3
4
5
6
WP1050.book  Page 177  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
178For assistance, please visit http://www.panasonic.com/help
[UPnP Port Mapping Table] shows the UPnP status and port mapping table.
UPnP Port Mapping Table:
1UPnP Status: Show whether UPnP feature is enabled or not.
2UPnP Port Mapping Table: Show the  list of UPnP client host’s IP address, 
along with the protocol and port number set to be 
opened for a specified amount of time for 
communication with UPnP feature.
1
2
WP1050.book  Page 178  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
For assistance, please visit http://www.panasonic.com/help179
[Wireless Status] shows the wireless LAN status.
Wireless Status:
1Mode: Show 802.11b or 802.11b/g.
2SSID: Show the network name.
3Channel: Show wireless data channel.
4SSID Broadcast: Show whether the SSID Broadcast feature is 
enabled or not.
5BSSID: Show the base unit’s MAC address currently in use 
by the handset.
6Security: Show the authentication methods and/or 
encryption types and Key Index number used for 
the wireless devices connected to the local 
network.
7MAC Address Filtering: Show whether the MAC address filtering is 
enabled or not.
8Client MAC Address: Show the MAC addresses of the wireless devices 
connected to the local network.
12
3
4
5
6
7
8
WP1050.book  Page 179  Wednesday, November 22, 2006  9:24 AM 
						

							Base Unit Settings
180For assistance, please visit http://www.panasonic.com/help
[Handset Status] shows the handset connection status.
Note:
LIt may take a while to display this screen in order to check if the handset is connected. Handset Status:
1Connection: Show the status of the handset registration and 
connection to the base unit.
2MAC Address: Show the MAC address of the registered handset.
3IP Address: Show the IP address of the handset.
1
23
WP1050.book  Page 180  Wednesday, November 22, 2006  9:24 AM