Panasonic Pv Vm202 Operating Instructions Manual

							31
Playback Zoom Function
A part of the image can be enlarged up to 10 times during playback.
1During playback, press the Playback Zoom Button 
[P.B. ZOOM] on the Remote Controller.
≥The center of the image is enlarged to approximately double the size.
Changing the Zoom Magnification
2Change the magnification by pressing the [W] or [T] Button 
on the Remote Controller.
≥You can increase the magnification up to 10k.
Changing the enlarged area of an image
3Press the Arrow Button (π, ∑, ∏, ∫) on the Remote 
controller that points to the area you want to enlarge.
Canceling the Playback Zoom Function
Press the [P.B. ZOOM] Button on the Remote Controller.
≥For other notes, see page 62.
~~~~~~~~~~~~~~~~~~~~~~~~~Playback Digital Effect Functions
During playback, special Digital Effects can be added to the Recording. The 
digital effects that may be applied in the process of recording (except Picture 
in Picture Mode) will be the same as these added effects.
1Press the [1] Button.
2Press the [SELECT] Button of the Remote Controller and 
select desired Digital Effect .
≥When the [SELECT] Button is pressed repeatedly, the Digital Effect 
selection changes.
MULTI  )WIPE )MIX )STROBE  )NEGA )SEPIA )MONO 
)TRAIL ) SOLARI  )MOSAIC ) MIRROR
≥The same setting can also be set using the [DIGITAL EFFECT] on the 
[VCR FUNCTIONS] Main-Menu.
Suspending Playback Digital Effect Temporarily
Press the [OFF/ON] Button 1 to clear or restart the digital effect. When the 
Digital effect is paused temporarily, the selected effect’s indication flashes.
Canceling the Digital Effect
Press the [SELECT] Button on the Remote Controller repeatedly until the 
Digital Effect Indication is cleared.
≥For other notes, see page 62.
~~~~~~~~~~~~~~~~~~~~~~~~~ªPlayback with Wipe Mode and Mix Mode
1
Press the [1] Button.
2Press the [SELECT] Button of the Remote Controller and 
select [WIPE] or [MIX].
3Press the [STORE] Button at the moment you want to save 
as a still picture.
≥The last scene is stored in memory. The [WIPE] or [MIX] Indication 
changes to [B] or [C].
4Press the [OFF/ON] Button in the scene in which you want to 
use the Wipe or Mix effect.
≥The scene changes as a result of the Wipe or Mix effect.
≥The Wipe Function and Mix Function can be used only from the Remote 
Controller during playback.
≥If the [OFF/ON] Button is pressed while Wipe or Mix is used, the effect will 
stop temporarily at that point. Pressing the [OFF/ON] Button again will bring 
back the effect.
ZOOM 2t
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
2
1
3
WIPE
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
1
2
3
4
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VAR.
SEARCHP.B.
ZOOM
1
2
1

						

							32ªPlaying Back with Multi-Picture Mode 
Strobe Multi-Picture Mode [STROBE] 1:
You can capture 9 consecutive still pictures from playback images.
Manual Multi-Picture Mode [MANUAL] 
2:
Selecting a desired still picture one at a time, you can capture 9 still pictures.
Index Multi-Picture Mode ([PHOTO], [SCENE]) 
3:
You can capture 9 screens of pictures to which index signals are attached.
After setting [VCR FUNCTIONS] >> [DIGITAL EFFECT] >> 
[EFFECT SELECT] >> [MULTI].....
1Set [MULTI-PICTURES] >> [SCAN MODE] >> [STROBE] or 
[MANUAL] or [PHOTO] or [SCENE], whichever mode you 
prefer.
When [STROBE] is selected:
≥Set the [SPEED] to a desired strobe speed.
[FAST]:You can capture 9 consecutive still pictures within 
approximately 1 second
[NORMAL]:You can capture 9 consecutive still pictures within 
approximately 1.5 seconds
[SLOW]:You can capture 9 consecutive still pictures within 
approximately 2 seconds
≥If you set [SWING] on the [MULTI-PICTURES] Sub-Menu to [ON], the 
intervals at which the 9 still pictures are taken are longer at the 
beginning and end than in the middle of the swing strobe period, and it 
is useful for analyzing swing motion, etc., in sports.
2Exit the Menu by pressing the [MENU] Button.
3Play back the tape.
≥If you select Index mode, it is not necessary to play back the tape.
4Press the [MULTI] Button.
≥If [STROBE] is selected: 9 screens are automatically captured from 
the point at which the Button is pressed.
≥If [MANUAL] is selected: press the [MULTI] Button at each scene you 
want to capture.  When 9 screens are captured, the tape will stop.
≥If [PHOTO] or [SCENE] is selected: From the point at which the 
Button is pressed, 9 screens of pictures to which index signals are 
attached are captured in the playback direction. After 9 screens are 
captured, the tape will stop, but, if there are 8 or less pictures to be 
captured, the tape will stop at its end.
Deleting All the Captured Multi-Pictures
While displaying the multi-pictures that have been captured, press the 
[MULTI] Button.
≥If [MANUAL] has been selected, press [MULTI] Button after 9 screens are 
displayed.
To Display the Multi-Pictures again
Press the [MULTI] Button for 1 second or longer.
To Delete Multi-Picture one by one (When Pictures have been 
captured in Manual Mode)
When the [MULTI] Button is pressed for 1 second or longer while the still 
pictures are displayed, the picture that was captured last is deleted. If you 
continue to press the Button, the pictures are deleted consecutively.
≥After still pictures are deleted one at a time, they cannot be displayed again.
To Stop Capturing Pictures midway (When Pictures have been 
captured in Index Mode)
Press the [∫] Button.
To Search the tape position of a desired picture among the 
playback pictures displayed on 9 screens
1
11 1After displaying pictures in Multi-Picture Mode, rotate the 
[PUSH] Dial to select the image whose tape position you 
want to search.
≥The selected picture blinks at the red frame.
2
22 2Press the Index Button [:] or [9] 4 on the Remote 
controller.
≥Still picture playback takes place at the selected picture.
≥For other notes, see page 62.
1
2
3
2
4
1, 1W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 243 1, 2
ZOOM
INDEX INDEX
SELECT
STORESTOP
KL∫
OSD
COUNTER
V/REW
STILL ADV
OFF/ON
P.B.DIGITAL
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV
MENU
ITEMSET
61 5
;ED
VA R .
SEARCHP.B.
ZOOM
BACKLIGHT
CAMERA
STILL

						

							33
Playing Back on Your TV
By connecting your Palmcorder with your TV, the recorded scenes can be 
viewed on your TV screen.
≥Before connecting them, turn off the power of both the Palmcorder and TV.
1Connect the [A/V IN/OUT] Jack of the Palmcorder to the 
Video and Audio Input Jacks of the TV.
≥Using the A/V Cable 1 (supplied), make a connection with the TV. If 
the TV has an S-Video Jack, connect the S-Video Cable (not supplied) 
2, too.
Making the Indications Appear on the TV screen
Press the [OSD] Button 3 on the Remote Controller.
≥Be sure to select the proper input on your TV. (If necessary, consult your 
TV’s operating instructions.)
≥If you play back a Cassette recorded with copyright protection signals, the 
screen becomes blue or mosaic-like noise patterns appear.
≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/OUT], 
nothing will be shown on the TV screen except during playback.
~~~~~~~~~~~~~~~~~~~~~~~~~Audio Dubbing
You can add music or narration to the recorded Cassette.
≥If you perform audio dubbing onto a tape that was recorded with 
[AUDIO-REC] on the [RECORDING SETUP] Sub-Menu of the 
[CAMERA FUNCTIONS] Main-Menu set to [16bit], the original sound is 
erased.
 (If you want to preserve the original sound, use the [12bit] Mode 
when recording.)
≥Audio Dubbing cannot be performed onto recordings made in LP Mode. 
(l19)
1Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> [AV JACK] 
>>[IN/OUT].
2And then select [A.DUB INPUT] >> [MIC] or [AV IN].
≥Set to [AV IN] when an external device is used, or set to [MIC] when 
built-in microphone is used.
3Press the [1] Button, and then press the [;] Button at the 
point where you want to start dubbing.
4Press the [A.DUB] Button on the Remote Controller.
≥[A.DUB;] Indication appears. 1
5
To start Audio Dubbing, press the [;] Button on the Remote 
Controller.
≥[A.DUB!] Indication appears. 2
To Stop Audio Dubbing
Press the [;] Button on the Remote Controller.
The Palmcorder is in the Still Playback Mode again.
Playing Back the Sound Recorded with Audio Dubbing 
(For 12 bit Audio Recording)
Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [AUDIO] >> [ST2] 
or [MIX].
ST1: Play back only the original sound.
ST2: Play back only the sound added by Audio Dubbing
MIX: Play back both the original sound and the sound added by Audio 
Dubbing simultaneously.
≥For other notes, see page 62.
4
3, 53
1, 2W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
1
A.DUB;A.DUB!
12
ZOOM
INDEX INDEX
SELECT
STOPKL∫
OSD
COUNTER
V/REW
STILL ADV
DATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/W
STILL ADV61 5
;ED
VA R .
SEARCHP.B.
ZOOM
[VIDEO IN]
[AUDIO IN]
[S-VIDEO IN]
1
ZOOM
INDEX INDEX
SELECT
STOP OSD
COUNTER
STILL ADV
DATE/
TIME
RESET TITLE T
WMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAUSE
FF/
STILL ADV
VA RPB
S-VIDEO 
IN/OUT

						

							34
Special Features
DV Camera Style and SD Camera Style 
This is a Digital Video Camera which can be used in two ways depending on 
the situation.
One is the DV Camera Style 
1 which combines the Camera Unit 2 and 
Video Unit 3, and the other is the SD Camera Style 4 which combines the 
Camera Unit 
2 and the supplied Battery Adaptor Unit 5.
DV Camera Style
≥Both Tape and Card can be used.
SD Camera Style
≥It is easy to carry, because it’s small and lightweight.
≥Tape cannot be used.
~~~~~~~~~~~~~~~~~~~~~~~~Attaching the Battery Adaptor Unit
Mounting the Battery Adaptor Unit allows the Palmcorder to be compact as 
well as light and portable.
≥Please carry out the Attachment/Removal of the Battery Adaptor Unit 
while the Palmcorder switch is off. Do not remove the Unit while the 
operation mode lamp is lit.
1While sliding the [CAMERA RELEASE] Lever 1, pull the 
Camera Unit straight out in the direction of the lens.
2Match the mark 2 and place the Camera Unit on the Battery 
Adaptor Unit.
3Slide the Camera Unit until it locks with a click.
Removing the Battery Adaptor Unit
While sliding the [CAMERA RELEASE] Lever 1, pull the Camera Unit 
straight out in the direction of the lens.
≥When the red portion 
3 of the [CAMERA RELEASE] Lever shows or the 
Camera Unit is not completely installed, the Palmcorder cannot be powered  
on. The Camera Unit must be shifted to the end again and locked.
~~~~~~~~~~~~~~~~~~~~~~~~Attaching the Battery
1
11 1Slide the [OPEN] Lever upwards to open the Battery Door 1.
2
22 2Insert the battery completely.
3
33 3Close the Battery Door.
Removing the Battery
Slide the [OPEN] Lever to open the Battery Door, and then slide the Battery 
Eject Lever 2. Finally slide the Battery to remove it.
≥For other notes, see page 62. 
3 2
CAMERA RELEASE32
CAMERA RELEASE1
1
1
2, 3
OPEN
1
2
2
53
1
4

						

							35
1
3
42
A
ACCESS
CARD EJECT65
1
F 7640
1
TAPE
CARD
5
PHOTO
SHOT
3, 4
3W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
STILL MPEG4 VOICE
CARD
MODE2
BACKLIGHT
CAMERA
STILL
Using a Memory Card
A Card can be used to record files or play back files.
≥Use genuine SD Memory Card or MultiMediaCard only.
ªInserting a Memory Card
Before inserting a Memory Card, be sure to turn off the Palmcorder.
1While holding the Memory Card with its cut off corner A 
facing right 
1, insert it into the Card Slot 2.
≥The display of the Card Slot changes from 3 to 4.
Ejecting a Card
After turning the Palmcorder off, slide the [CARD EJECT] Lever 
5 to the left.
ª[ACCESS] Lamp
While the Palmcorder is accessing the Card (reading, recording, playback, 
erasing, moving of images), the [ACCESS] Lamp 
6 lights up.
≥While the [ACCESS] Lamp is on, never attempt to: pull out the Card, turn 
off the Palmcorder power, or switch the [TAPE/CARD] Selector. Such 
actions will damage the Card and cause the Palmcorder to malfunction.
~~~~~~~~~~~~~~~~~~~~~~~~~Recording on the Memory Card
Three kinds of data can be recorded by selecting with the 
[STILL/MPEG4/VOICE] Selector. When recording still pictures, select [STILL] 
(Card PhotoShot), when recording moving pictures, select [MPEG4] 
(MPEG4 Recording), when recording voice, select [VOICE] 
(Voice Recorder Function).
≥If the [TAPE/CARD] Selector is set to [CARD], the Palmcorder is 
automatically turned off when you leave it for about 5 minutes without 
performing any PhotoShot recording.
≥When the [TAPE/CARD] Selector is set to [CARD], you cannot record to the 
Tape.
ªCard PhotoShot
Still pictures can be recorded on the Memory Card from the Palmcorder lens 
as well as from scenes that have already been recorded on a cassette.
The size of images that are recorded using this Palmcorder is approximately 
1,080,000 pixels. Recording of images with a size that is larger than a million 
pixels is called mega-pixel still-picture recording. Compared to images of 
normal recording, images that are created by mega-pixel still-picture 
recording can be printed more clearly.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Set [CAMERA FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE SIZE] >> [1200k
kk k900] or [640k
kk k480].
4Set the [PICTURE QUALITY] to desired picture quality.
5Press the [PHOTO SHOT] Button.
≥The [ ] Indication will light in red.
≥Mega-pixel recording (when you select [1200t900] in step 3) is useful for 
taking clear pictures, but the following functions are disabled during mega-
pixel recording.
≥Digital zooming (l 22)
≥Digital Electronic Image stabilizer function (l 22)
≥Digital Effect functions (l 26, 27)
≥Title In/Creation (l 42)
≥The power is automatically turned off after about 5 minutes when a card has 
been inserted.PICTURE

						

							36
F 7640
1, 2
TAPE
CARD
4, 4
PHOTO
SHOT
3, 1
3, 1W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
ACCESS CAMERA
CARD P. B.
VCR
STILL
RESETMPEG4 VOICE
CARD
MODE2, 3
OFF ONMODE
4BACKLIGHT
CAMERA
STILL
POWER
ªCard PhotoShot (continued)
Recording from a Cassette (VCR Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Set [VCR FUNCTIONS] >> [CARD SETUP] >> 
[PICTURE QUALITY] >> a desired picture quality.
4Start playback and press the [PHOTO SHOT] Button at the 
scene you want to record.
≥The size of the images input externally or recorded from a tape to the 
card becomes [640k480].
≥While the image is being recorded, it stays still for a few seconds.
Recording from other equipment 
1
11 1Set the [PICTURE QUALITY] on the [CARD SETUP] 
Sub-Menu to desired picture quality.
2
22 2Slide the [TAPE/CARD] Selector to [CARD].
3
33 3Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
4
44 4Input the picture from the other equipment then press the 
[PHOTO SHOT] Button at the desired scene.
Selecting the quality of Card PhotoShot images
1Set [CAMERA FUNCTIONS] or [VCR FUNCTIONS] >> 
[CARD SETUP] >> [PICTURE QUALITY] >> a desired picture 
quality.
Maximum number of images recordable on the supplied Card (16MB)
When the picture size is 1200k
kk k900:
[FINE] (high image quality): approximately 23 pictures
[NORMAL] (Normal): approximately 42 pictures
[ECONOMY] (low image quality): approximately 65 pictures
When the picture size is 640k
kk k480:
[FINE] (high image quality): approximately 100 pictures
[NORMAL] (Normal): approximately 200 pictures
[ECONOMY] (low image quality): approximately 400 pictures
≥For other notes, see page 63.

						

							37
ªAutomatically copying still pictures recorded on a 
cassette
The Palmcorder copies images automatically, referring to Photo Index 
signals.
After setting the Palmcorder to the VCR Mode (l 28).....
1Set the Palmcorder to Still Playback Mode just before the 
point where picture transfer is to commence.
2Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> 
[RECORD TO CARD] >> [YES].
≥Search starts from the current Cassette position, and images with 
Photo Index signals are recorded onto the Card sequentially.
≥While copying, the indication 
1 appears.
To Stop the Transfer of Images
Press the [∫] Button.
≥For other notes, see page 62. 
~~~~~~~~~~~~~~~~~~~~~~~~~
Using the Video Flash
Using the Video Flash of the Battery Adaptor Unit allows a PhotoShot in dark 
places.
Video Flash can be used in SD Camera Style only.
1Set [CAMERA FUNCTIONS] >> [RECORDING SETUP] >> 
[FLASH] >> [ON].
≥The [ß] Indication appears. 1≥Setting to [AUTO] allows the flash to fire when recording in a dark place.
2Press the [PHOTO SHOT] Button.
To reduce the “red eye” phenomenon in your pictures 
(Red Eye Reduction)
When setting the [RED EYE REDUCTION] in the [RECORDING SETUP] 
Sub-Menu to [ON], the [£] Indication 2 is displayed.
≥The available range of the Video Flash is approximately 1 to 2.5 metres in a 
dark place. Pictures will appear dark when they are recorded using the 
Video Flash at distances greater than 2.5 metres.
≥Continuous PhotoShot is not possible if the Video Flash is used.
≥When this Palmcorder is used in SD Camera Style, the Palmcorder will 
automatically detect the surrounding brightness and determine if the flash is 
necessary or not. (Regardless of setting [FLASH] to [OFF], the [
ß] flashes 
when a source of light is necessary.)
1
1 2W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2PHOTO SHOT
1 2£ ßF 7640
 æ
1
NOW WRITING;
TAPE
CARD%
2W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
1
1 2
F 7640
BACKLIGHT
CAMERA
STILL

						

							38ªRecording Moving Pictures
 (MPEG4)
You can record moving pictures for e-mailing on a Memory Card. The 
recorded data can be also played back on Windows Media Player.
Recording from the Palmcorder Lens (Camera Mode)
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3Press the Recording Start/Stop Button.
≥It takes 2 to 3 seconds to start recording.
≥During recording, the [ ] Indication is lit in red. 
≥The maximum continuous recording time is 60 minutes.
The Palmcorder will automatically stop recording when the relevant 
time listed above has elapsed.
≥When Remaining Time Indication becomes [R:0h00m], 
[NO SPACE LEFT] Indication appears. Recording may not be started.
≥The shutter speed is adjustable within the range of 1/60 to 1/500 while 
recording moving pictures (MPEG4)
.
≥The picture size of the moving picture (MPEG4) is set to be [176k144].
≥When attaching to email, we recommend the picture size to be less than 
1MB (about 1 minute length).
≥The following functions are disabled.
≥Digital Zoom (l22)
≥Cinema Function (l23)
≥Digital Effect Functions (l26)
≥Title In/Creation (l42)
≥Fade In/Out Function (l22)
Recording from a Cassette (VCR Mode)
1
11 1Slide the [TAPE/CARD] Selector to [CARD].
2
22 2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3
33 3Start playback and press the Recording Start/Stop Button at 
the desired scene.
Recording from other equipment 
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3Input the image from other equipment then press the 
Recording Start/Stop Button at the desired scene.
Maximum recording time on the supplied Card (16 MB)
Approximately 15 minutes
≥The video resolution of the camera is reduced when making a MPEG4 
recording. This is done in order to optimize the image quality in MPEG4 
recordings, and does not reflect a problem with the software or hardware.
≥For other notes, see page 63.
ªRecording Voice (Voice Recording Function)
You can record voice data on a card.
1Slide the [TAPE/CARD] Selector to [CARD].
2Slide the [STILL/MPEG4/VOICE] Selector to [VOICE].
3Press the Recording Start/Stop Button.
≥Voice from built-in microphone is recorded.
≥It takes 2 to 3 seconds to start recording.
≥The recorded file is automatically locked (to prevent accidental 
erasure).
≥During recording, the [ ] Indication is lit in red. 
≥If a card is not inserted, the Indication flashes in red.
≥When Remaining Time Indication becomes [R:0h00m], 
[NO SPACE LEFT] Indication appears. Recording may not be started.
≥For other notes, see page 63.
MPEG4MPEG4
VOICEVOICE
R: 0h20m
TAPE
CARD
2, 2, 2
1, 1, 1
3, 3, 3
STILL MPEG4 VOICE
CARD
MODE
TAPE
CARD
2
1 3STILL MPEG4 VOICE
CARD
MODE
R: 0h20m

						

							39
Playing Back Files from the Memory Card
It allows you to play back files recorded on a Card.
≥When you set the Palmcorder to Card Playback Mode, the Card Contents 
1 are displayed to inform you which kind(s) of data (still picture, moving 
picture and/or voice data) are recorded on the Card.
ªPlaying back Still Pictures
1
Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
2Set the [STILL/MPEG4/VOICE] Selector to [STILL].
≥The still picture that was recorded last on the Card is displayed.
3Start Playback.
1: Start Slide Show (The [SLIDE!] Indication is displayed)
5: Playing back the next Picture
6: Playing back the previous Picture
∫: Stop the slide playback
;: Pause slide playback
ªPlaying back Moving Pictures (MPEG4) 
1
11 1
Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
2
22 2Set the [STILL/MPEG4/VOICE] Selector to [MPEG4].
3
33 3Start Playback.
1: Playing back
∫: Stop the playing back
;: Pause playing back (This button does not pause playing back within 
2 seconds of finishing playing back.)
5: (Stop Mode) To the beginning of the next file.
(Playback Mode) To the beginning of the next file and start playback.
(Pause Mode) To the beginning of the next file and turns to Stop Mode.
6: (Stop Mode) To the beginning of the previous playback file.
(Playback Mode) To the beginning of the playback file and start 
playback.
(Pause Mode) To the beginning of the file under playback and turns to 
Stop Mode.
≥File is numbered in hexadecimal form.
≥When the object is moving fast or zoom operation is performed, picture may 
appear to be still or mosaic noise pattern appears, but this is not a 
malfunction.
ªPlaying back Voice 
1Set the Palmcorder to Card Playback Mode.
≥The [CARD P.B.] Lamp lights up.
2Set the [STILL/MPEG4/VOICE] Selector to [VOICE].
3Start Playback.
1: Playing back
∫: Stop the playing back
;: Pause playing back (This button does not pause playing back within 
2 seconds of finishing playing back).
5: (Stop Mode) To the beginning of the next File.
(Playback Mode) To the beginning of the next File and start playback.
(Pause Mode) To the beginning of the next File and turns to Stop Mode.
6: (Stop Mode) To the beginning of the previous playback File.
(Playback Mode) To the beginning of the playback File and start 
playback.
(Pause Mode) To the beginning of playback File and turns to Stop 
Mode.
≥If the  [6
66 6] Button or [5
55 5] Button is pressed for 1 or more seconds, it 
becomes 10k playback and if pushed for 7 or more seconds, it becomes 
60k playback. Releasing the Button brings back to normal playback.
2Folder-File Number (When the PICTURE or MPEG4 is played back only)
3Picture Size (When the PICTURE is played back) Playback time (When MPEG4 data or VOICE data is played back)4File Number
To adjust the volume (Only Playing back MPEG4 and VOICE)
≥During playback, hold down the [PUSH] Dial until the volume Indication 
appears and rotate it to adjust the volume. (l28)
2
ACCESS CAMERA
CARD P. B.
VCR
RESET2, 2, 2 
1, 1, 
1  3, 3, 3 
STILL MPEG4 VOICE
CARD
MODE
OFF ONMODE
PICTURE100-0012
MPEG4MOL012.ASF
VOICE
3
4 3
4 3
4
2
BACKLIGHT
CAMERA
STILL
POWER
1CARD CONTENTS
PICTURE
MPEG4
VOICE

						

							40
ªTo Select a Desired File and Play it Back
After setting the Palmcorder to the Card Playback Mode (l 39).....
1Slide the [STILL/MPEG4/VOICE] Selector to desired type of 
data.
2Press the [MULTI] Button.
≥The files recorded on the Memory Card are displayed in Multi-Picture 
Mode. 
1
3
Rotate the [PUSH] Dial and select a desired file.
≥The selected file is marked with a red frame.
≥When 7 or more files have been recorded, rotate the [PUSH] Dial to 
display the next file. The [6] Button or [5] Button can be used 
instead of the [PUSH] Dial.
4Press either the [PUSH] Dial or the [MULTI] Button.
≥The selected file is shown on the entire screen.2 File Size (When [STILL] is selected at Step 1)
3 File Number4 Folder-File Number (When [STILL] or [MPEG4] is selected at Step 1)
ªUsing File Search Mode
1
11 1
Set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[FILE SEARCH] >> [YES].
≥The file search screen 5 appears.
2
22 2Rotate the [PUSH] Dial to select the desired number of the 
file and then press it.
≥The selected number’s file appears.
≥The same process can be performed using the short-cut menu (l 18).
≥For other notes, see page 63. 
~~~~~~~~~~~~~~~~~~~~~~~~
Copying pictures on a Memory Card to a 
Cassette
After setting the Palmcorder to the Card Playback Mode (l 39).....
To Copy One Picture
1Slide the [TAPE/CARD] Selector to [TAPE].
2Slide the [STILL/MPEG4/VOICE] Selector to [STILL].
3Display a desired picture.
≥Please refer to “To select a Desired File and Play it Back”.
4Press the [PHOTO SHOT] Button.
≥It takes approximately 7 seconds to copy a still picture to the Cassette.
≥During the copying, the indication 
1 appears.
To Copy All the Pictures
1
11 1Display the first picture.
≥If a picture other than the first one is displayed, only the subsequent 
pictures will be copied.
2
22 2Set [CARD FUNCTIONS] >> [CARD EDITING] >> 
[RECORD TO TAPE] >> [YES].
≥It takes approximately 7-11 seconds for each picture to be copied to the 
cassette. To stop the copying midway, press the [∫] Button.
≥During the copying, the indication 
1 appears.
≥When recording to tape, select the tape position before recording. The 
picture will be recorded to the tape position when the [PHOTO SHOT] 
button is pressed at step 4.
≥When pictures with a size other than [640k480] are copied to the cassette, 
their pictures quality will deteriorate slightly.
≥Picture size recorded on tape is [640k480]. (Cannot save as mega-pixel 
still picture)
≥Moving Picture (MPEG4) and Voice data cannot be recorded from a card to 
tape.
≥When recording the Card Images on a Tape, a PhotoShot index signal is 
automatically recorded with a picture.
≥Even if you edit the Slide Show, it is not applied to the order in copying the 
pictures.
≥For other notes, see page 62.
1
NOW RECORDINGREC
4PHOTO
SHOT
2
2W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
1
TAPE
CARD
ACCESS CAMERA
CARD P. B.
VCR
RESET2STILL MPEG4 VOICE
CARD
MODE
OFF ONMODE
POWER
ACCESS CAMERA
CARD P. B.
VCR
RESET1 3, 4, 1,2
W.B./SHUTTER/IRIS/
MF/VOL/JOG
PUSH1 2
2, 4 1
1
2
5PICTURE
No.25           100-0012
640
640
1200
640
640
1200
No.3
FILE SEARCH
PUSH MENU TO RETUR
STILL MPEG4 VOICE
CARD
MODE
OFF ONMODE
34
BACKLIGHT
CAMERA
STILL
POWER