Panasonic Pv Gs120 Operating Instructions Manual

							Recording Mode
-41-
1Set [TAPE RECORDING MENU] >> 
[DIGITAL] >> [EFFECT1] >> [WIPE] or [MIX].
≥The [WIPE] or [MIX] Indication appears.
2Press the Recording Start/Stop Button (42) 
to start recording.
3Press the Recording Start/Stop Button (42) 
to pause the recording.
≥The last scene is stored in memory. The 
[WIPE] or [MIX] Indication changes to [B] 
or [C].
4Press the Recording Start/Stop Button (42) 
to restart the recording.
≥The last image of the previous scene 
gradually changes to the new scene.
≥For other notes concerning this item, see 
-75-.
STILL
ENTERFA D E
MENU
i s
(14)
(42)
PV-GS120_200Eng.book  41 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-42-
Playback Mode
Playing Back a Tape
The recorded scene can be played back 
immediately after the recording.
1Set the [OFF/ON] Switch (43) to [ON].
≥The [POWER] Lamp (41) lights up.
2Set the Mode Dial (39) to Tape Playback 
Mode.
3Press the [6] Button (19) to rewind the 
tape.
≥Rewind the tape to the point where you want 
to start playback.
≥When the tape reaches the beginning, 
rewinding stops automatically.
4Press the [1] Button (17) to start playback.
≥The [!] Indication appears.
≥If a cassette recorded with a copyright 
protection signal is played back, the picture is 
distorted by mosaic-like patterns.
To Stop PlaybackPress the [∫] Button (18).
ONOFF
POWER(41)
(43)
PCSD(39)
ENTERFA D E
STILL
i s(19)
FA D E
STILL
ENTERi s(17)
(18)ENTERFA D E
STILL
i s
ªAdjusting the Sound VolumeTo adjust the volume, push the [`VOL/JOG_] 
Lever (46) to display the [VOLUME] Indication. 
Push the [`VOL/JOG_] Lever towards [T] to 
increase the volume or push the [`VOL/JOG_] 
Lever towards [W] to decrease the volume. The 
[VOLUME] Indication goes off after the 
adjustment is finished.
To adjust the volume with the Remote Controller, 
press the [T] or [W] Button to display the 
[VOLUME] Indication. Press the [T] Button to 
increase the volume or press the [W] Button to 
decrease the volume. The [VOLUME] Indication 
goes off after the adjustment is finished.
≥The sound volume cannot be adjusted using the 
Remote Controller in Playback Zoom Mode. 
(
-44-)
≥For other notes concerning this item, see 
-75-.
Finding a Scene You Want to Play 
Back
ªCue/Review Playback
If the [5] Button (16) or [6] Button (19) is 
pressed during Playback, it turns to Cue Playback 
A or Review Playback B.
≥If the Button is held continuously, it turns to Cue 
Playback or Review Playback until you release 
it.
VOL/JOG
WT(46)
ENTERFA D E
STILL
i s
(19)        (16)
AB
PV-GS120_200Eng.book  42 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-43-
ªVariable Speed Search FunctionThe speed of Cue Playback or Review Playback 
can be varied.
1During playback, press the [1] Button (17).
≥The [1k!] Indication appears.
2Push the [sVOL/JOGr] Lever (46) to select 
a desired search speed.
The following 6 playback speeds are available for 
the Variable Speed Search Function in both the 
fast-forwarding and rewinding directions: 
1/5k (slow playback in SP Mode only), 1/3k 
(slow playback in LP Mode only), 1k, 2k, 5k, 
10k and 20k.
≥This function works by pressing the 
[VAR. SEARCH] and [T] or [W] Button on the 
Remote Controller. (
-14-)
To Resume Normal PlaybackPress the [1] Button (17).
≥During Cue or Review Playback, fast-moving 
images may show mosaic-like patterns.
≥The sound is muted during search.
Slow Motion Playback
This Camcorder can play back at a slow speed.
1Press the [1] Button (79).2Press the [E] Button or [D] Button (64) on 
the Remote Controller.
≥The [}] or [~] Indication appears.
≥When the [E] Button is pressed, Slow Motion 
Playback proceeds in the reverse direction. 
When the [D] Button is pressed, Slow Motion 
Playback proceeds in the forward direction.
FA D E
STILL
ENTERi s(17)
VOL/JOG
WT(46)
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsPLAY
PAs S E
FF/W
STILL ADV61 5
;EDP.B. ZOOM
(79)
(64)
(64)
}
Scenes recorded in the SP Mode are played back 
at approximately 1/5th of the normal speed.
Scenes recorded in the LP Mode are played back 
at approximately 1/3rd of the normal speed.
To Resume Normal PlaybackPress the [1] Button (79).
≥If the Camcorder is left in the Slow Motion 
Playback Mode for more than 10 minutes, the 
Camcorder switches to the Stop Mode to 
protect the video heads from excessive wear 
and tear.
Still Playback/Still Advance 
Playback
This Camcorder is capable of still picture 
playback and frame-advance playback.
1Press the [1] Button (79).2Press the [;] Button (76).
≥The playback image stops in the Still 
Playback Mode.
3Press the [E] Button or [D] Button (64) on 
the Remote Controller.
≥With each press of the [E] Button, still 
pictures advance in the reverse direction. 
With each press of the [D] Button, still 
pictures advance in the forward direction. If 
one of the buttons continues to be pressed, 
still pictures advance continuously 1 frame at 
a time until the button is released.
To Resume Normal Playback
Press the [1] Button (79).
ªPlayback with Volume/Jog LeverBy pushing the [`VOL/JOG_] Lever (46) of the 
Camcorder in the Still Playback Mode, still 
pictures can be advanced one frame at a time in 
the forward or backward direction. If you keep 
pushing the Lever, still pictures advance 
continuously.
≥If the Camcorder is left in the Still Playback 
Mode for more than 5 minutes, the Camcorder 
switches to the Stop Mode to protect the video 
heads from excessive wear and tear.
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(79)
(76)
(64)(64)
VOL/JOG
WT(46)
PV-GS120_200Eng.book  43 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-44-
Index Search Functions
To facilitate searching for desired scenes, this 
Camcorder automatically records index signals 
during recording, as explained in the following.
Photoshot Index Signal
These signals are automatically recorded when 
still pictures on a card are recorded to a tape.
Scene Index Signal
Scene Index Signals are automatically recorded 
when you start recording after inserting a 
Cassette.
≥If [SCENE INDEX] of [RECORDING] Sub-Menu 
on the [TAPE RECORDING MENU] is set to 
[2HOUR], an index signal is recorded when 
recording is restarted after a lapse of 2 hours or 
longer. If it is set to [DAY], an index signal is 
recorded when recording is restarted after the 
date has changed since the last recording. 
(While the index signal is being recorded, the 
[INDEX] Indication flashes for a few seconds.)
≥If the Camcorder is switched from the Tape 
Playback Mode to Tape Recording Mode or if 
the date and time is set before the start of 
recording, the index signal is not recorded.
ªPhotoshot Index Search
1Set [TAPE PLAYBACK MENU] >> 
[PLAYBACK] >> [SEARCH] >> [PHOTO].
2Press the [9] Button or [:] Button (65) 
on the Remote Controller.
≥With each press of the corresponding button, 
still pictures recorded in Photoshot Mode are 
searched.
ªScene Index Search
1Set [TAPE PLAYBACK MENU] >> 
[PLAYBACK] >> [SEARCH] >> [SCENE].
2Press the [9] Button or [:] Button (65) 
on the Remote Controller.
INDEX
STILL
ENTERFA D E
MENU
i s
(14)
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP.B. ZOOM(65) (65)
≥When the corresponding button is pressed 
once, the [S 1] Indication appears, and 
searching for the subsequent scene marked 
with an index signal starts. Each time the button 
is pressed after the start of Scene Index 
Search, the indication changes, from [S 2] to 
[S 9], and the beginning of the scene 
corresponding to the selected number will be 
searched.
≥Up to 9 scene numbers can be selected.
Continuous Index SearchIf the [9] Button or the [:] Button (65) is 
pressed for 2 seconds or longer, search can be 
continued at several-second intervals. (To cancel, 
press the [1] Button 
(79) or the [∫] Button (77).)
≥For other notes concerning this item, see 
-75-.
Playback Zoom Function
A part of the image can be enlarged up to 
10 times during playback.
1During playback, press the [P.B. ZOOM] 
Button (81) on the Remote Controller.
≥The center of the image is enlarged by 
approximately 2 times.
To Change the Zoom Magnification2Change the magnification by pressing the 
[W] Button or [T] Button (69) on the Remote 
Controller.
S   1
INDEX INDEX
SELECT
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(79)
(77)
INDEX INDEX
SELECT
STORESTOP
KL∫
OFF/ON
P B DIGITAL
ENTER
VAR.
SEARCHMENU
P.B. ZOOM(81)
(63)
(63)
ZOOM 2t 
ZOOM OSDDISPLAY
V/REWDATE/
TIME
RESET
TITLE T
W
sVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAYFF/
W61 5
(69)
PV-GS120_200Eng.book  44 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-45-
To Change the Enlarging Area of an Image
3Press the Arrow Button (π, ∑, ∏, ∫) (63) 
on the Remote Controller that points to the 
area you want to enlarge.
To Cancel the Playback Zoom FunctionPress the [P.B. ZOOM] Button (81) on the 
Remote Controller.
≥For other notes concerning this item, see 
-75-.
Playback Digital Effect Functions
During playback, special digital effects can be 
added to the recorded pictures. The same effects 
as those of Digital Effects 1 and 2, which are 
used during recording, are obtained.
1Press the [1] Button (79).
2Press the [SELECT] Button (66) on the 
Remote Controller to select a desired digital 
effect.
≥When the [SELECT] Button is pressed 
repeatedly, the digital effect selection 
changes.
≥The same setting can be done using 
[EFFECT SEL] Sub-Menu on the 
[TAPE PLAYBACK MENU].
To suspend Playback Digital Effect 
Temporarily
Press the [OFF/ON] Button (68) to suspend or 
restart the digital effect. When the digital effect is 
paused temporarily, the selected effect’s 
indication flashes.
To Cancel the Digital EffectPress the [SELECT] Button (66) on the Remote 
Controller and clear the digital effect indication.
ªWipe Mode and Mix Mode
1Press the [1] Button (79).
INDEX INDEX
SC
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(79)
SELECT
STORE
OFF/ON
P.B.DIGITAL
ENTER
VAR.
SEARCHMENU(66)
(68)
INDEX INDEX
SC
STOPKL∫
V/REW
STILL ADVWsVPLAY
PAUSE
FF/W
STILL ADV61 5
;EDP. B .  Z O O M
(79)
2Press the [SELECT] Button (66) on the 
Remote Controller and select [WIPE] or 
[MIX].
3Press the [STORE] Button (67) at the 
moment you want to save as a still picture.
≥The [B] or [C] Indication appears, and 
the image is saved.
4Press the [OFF/ON] Button (68) in the scene 
in which you want to use the Wipe or Mix 
effect.
≥The scene changes as a result of the Wipe or 
Mix effect.
≥The Wipe Function and Mix Function can only 
be accessed by using the Remote Controller 
during playback.
≥If the [OFF/ON] Button 
(68) is pressed while 
Wipe or Mix is carried out, the effect will stop 
temporarily at that point. Pressing the [OFF/ON] 
Button 
(68) again will bring back the effect.
≥For other notes concerning this item, see 
-76-.
Playing Back a Card
It plays back files recorded on a Card.1Set the Mode Dial (39) to Picture Playback 
Mode or MPEG4 Playback Mode. (MPEG4 
Playback Mode on PV-GS200 Model only)
2Start Playback.
[PICTURE]:
1: Starting the Slide Show
5: Playing back the next picture
6: Playing back the previous picture
∫: Stop the Slide Show
;: Pause the Slide Show
[MPEG4] (PV-GS200 only):
1: Playing back the File
5: Selecting the next file (When you press this 
button during playback, you can search the 
next file, and when you keep pressing it, cue 
playback is activated.)
6: Selecting the previous file (When you press 
this button during playback, you can search 
the beginning of the file, and when you keep 
pressing it, review playback is activated.)
∫: Stop playing back
;: Pause playing back
SELECT
STORE
KL∫
OFF/ON
P. B . D I G I TA L
ENTER
VAR.
SEARCHMENU(66)
(67)
(68)
PC
SD
P
C
SD(39)
PV-GS120_200Eng.book  45 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-46-
When you select MPEG4 Playback Mode at 
Step 1 (PV-GS200 only)
≥File is numbered in hexadecimal.
≥When the object is moving fast or zoom 
operation is performed, picture may appear to 
be still or mosaic-pattern noise may appear, but 
this is not a malfunction.
≥When you select MPEG4 Playback Mode at 
step 1, during playback, push the 
[`VOL/JOG_] lever to display the volume 
indication until the volume Indication appears 
and adjust the volume. (
-42-)
1Folder File Number (When the picture is 
played back)
File Name (When the MPEG4 data is played 
back) (PV-GS200 only)
2Picture Size (When the picture is played back) 
(
-69-)
Playback time (When MPEG4 data is played 
back) (PV-GS200 only)
3File Number
To Select a Desired File and Playing Back1Set the Mode Dial (39) to Picture Playback 
Mode or MPEG4 Playback Mode. (MPEG4 
Playback Mode on PV-GS200 Model only)
2Press the [MULTI] Button (10).
≥The files recorded on the Card are displayed 
in Multi-Picture Mode.
1Picture Size (When Picture Playback Mode is 
selected at Step 1)
2File Number
100-0001MPEG4
32
1
2
3 1
MOL-001.ASF
PC
SD
P
C
SD(39)
MULTI/
P-IN-P(10)
PICTURE
123No.25          100-0014
640
640
640
640
640
640
3Folder File Number (When Picture Playback 
Mode is selected at Step 1)
File Name (When MPEG4 Playback Mode is 
selected at Step 1) (PV-GS200 only)
3Press the [;/∫/6/5] Button to select a 
desired file.
≥The selected file is marked with a frame.
4Press either the [ENTER] Button (17) or the 
[MULTI] Button (10).
≥The selected file is shown on the entire 
screen.
≥For other notes concerning this item, see 
-76-. 
Slide Show
The recorded still pictures in the Card can be 
played back like a Slide Show.
1Set the Mode Dial (39) to Picture Playback 
Mode.
2Press the [1] Button (17).
≥The [SLIDE!] Indication is displayed.
≥Each of the pictures are played back for 
several seconds.
To Pause the Slide Show
Press the [;] Button.
≥The [SLIDE;] Indication is displayed.
To Stop the Slide ShowPress the [∫] Button.
≥For other notes concerning this item, see 
-76-.
STILL
ENTER
FA D E
PC
SD(39)
FA D E
STILL
ENTERi s(17)
SLIDE
SLIDE
PV-GS120_200Eng.book  46 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-47-
Creating a Title
You can create a title and record on a Card.1Recording Mode:
Set the Mode Dial (39) to Tape Recording 
Mode or Card Recording Mode. 
Set the Lens to the image you want to use 
for creating a title.
1Tape Playback Mode:
Search for the image you want to use for 
creating a title and set the Camcorder to the 
Still Playback Mode.
2Set [CARD] >> [CREATE TITLE] >> [YES].
3Press the [PHOTO SHOT] Button (47).
≥The title is stored.
≥To perform Photoshot again, select 
[RETURN].
4Select [LUMINANCE] and press the 
[ENTER] Button (17), then press the [5] 
Button (16) or [6] Button (19) to adjust 
the title contrast and press the [ENTER] 
Button 
(17).5Press the [5] Button (16) or [6] Button (19) to adjust the color and press the 
[ENTER] Button (17).
≥The dark portion of the image is missing 1, 
and the colors of the bright portion change in 
order of black, blue, green, cyan, red, 
PCSD(39)
ENTERFA D E
STILL
i s
(15)
STILL
ENTERFA D E
MENU
i s
(14)
PHOTO
SHOT
(47)
12
magenta, yellow and white, after which the 
bright portion of the image is missing 2 and 
the colors of the dark portion change in the 
above order.
6Select [RECORDING] and press the 
[ENTER] Button (17).
≥The title is recorded on the Card.
≥For other notes concerning this item, see 
-76-. 
Adding a Title
A title can be added to the picture. It is displayed 
in Tape/Card Recording Mode and Tape/Picture 
Playback Mode.
1Set [DIGITAL] >> [TITLE IN] >> [ON].
2Press the [MENU] Button (14).
≥The title is displayed.
3Press the [MULTI] Button (10).
≥A list of titles is displayed.
≥File Name 1
4Press the [;/∫/6/5] Button to select a 
desired title.
≥The selected title is marked with a frame.
r
STILL
ENTERFA D E
MENU
i s
(14)
MULTI/
P-IN-P(10)
TITLE
1USR00002.TTL
STILL
ENTER
FA D E
PV-GS120_200Eng.book  47 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-48-
5Press the [ENTER] Button (17) or press the 
[MULTI] Button (10).
≥The selected title is displayed.
≥Recording and Photoshot Recording can be 
made with pictures that have titles.
≥A title can be displayed also by pushing [TITLE] 
Button on the Remote Controller.
To Clear the Title Display
Set [DIGITAL] >> [TITLE IN] >> [OFF].
Or press [TITLE] Button (73) on the Remote 
Controller.
≥For other notes concerning this item, see 
-77-.
Writing Printing Data on a Card
(DPOF Setting)
DPOF Setting Printing data (DPOF Settings), 
such as the number of images to be printed, can 
be written to the Card. “DPOF” means Digital 
Print Order Format.
1Set the Mode Dial (39) to Picture Playback 
Mode.
2Set [PICTURE PLAYBACK MENU] >> 
[EDITING] >> [DPOF SET] >> [YES] >> 
[VARIABLE].
≥When all images are not printed, select 
[ALL 0].
3Select a desired picture and press the 
[ENTER] Button (17).
≥The selected picture is marked with a frame.
≥The number of prints set by DPOF 1 is 
displayed.
4Press the [5] Button (16) or [6] Button (19) to select the number of pictures to be 
printed, and press the [ENTER] Button (17).
≥[¥] Indication 2 is displayed in the picture 
set. (
-69-)
≥This is not the setting of the number of prints 
for printing on PictBridge. (
-54-)
PC
SD(39)
STILL
ENTERFA D E
MENU
i s
DPOF SETTING
!:ENTER    MENU:EXIT21
(14)
5Repeat Steps 3 and 4 and press the [MENU] 
Button (14) when the setup is completed.
To Verify DPOF SettingSelect [VERIFY] in Step 2. The pictures for which 
1 or more print is set in DPOF are played back 
continuously.
≥For other notes concerning this item, see 
-77-.
Protecting the Files on a Card 
(Lock Setting)
Precious files recorded on a Card can be locked 
to prevent accidental erasure. (Even if files are 
locked, the files will be deleted if the Card is 
formatted.)
1Set [PICTURE/MPEG4 PLAYBACK MENU] 
>> [EDITING] >> [FILE LOCK] >> [YES]. 
([MPEG4 PLAYBACK MENU] on PV-GS200 
Model only) 
2Select the file to be locked, and press the 
[ENTER] Button (17).
≥The selected file is locked and the [ ] 
Indication 1 appears. Repeat this procedure 
to lock 2 or more files.
≥Press the [ENTER] Button 
(17) again to 
cancel.
≥The SD Memory Card has a write protection 
switch. (
-77-)
≥For other notes concerning this item, see 
-77-.
STILL
ENTERFA D E
MENU
i s
(14)
FILE LOCK
!:ENTER    MENU:EXIT640640
640640640
6401
PV-GS120_200Eng.book  48 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-49-
Deleting the Files Recorded on a 
Card
Using the Camcorder, you can delete the files 
recorded on a Card. After the file is deleted, it 
cannot be restored.
To Select and Delete Files or Titles1Set [PICTURE/MPEG4 PLAYBACK MENU] 
>> [DELETE] >> [FILE BY SEL] >> [YES]. 
([MPEG4 PLAYBACK MENU] on PV-GS200 
Model only)
≥To erase a title in 
[PICTURE PLAYBACK MENU], select 
[TITLE BY SEL].
2Select the file you wish to delete and press 
the [ENTER] Button (17).
≥The selected picture is marked with a frame.
≥To erase 2 files or more, repeat this step.
3Press the [PHOTO SHOT] Button (47).
≥A verification message appears.
4Select [YES] and press the [ENTER] Button (17).
≥The selected file is deleted from the Card.
≥If [NO] is selected, the file selection is 
cancelled.
To Select and Delete All Files1Set [PICTURE/MPEG4 PLAYBACK MENU] 
>> [DELETE] >> [ALL FILES] >> [YES]. 
([MPEG4 PLAYBACK MENU] on PV-GS200 
Model only)
≥A verification message appears.
2Select [YES] and press the [ENTER] Button (17).
≥All files of Picture/MPEG4 Playback Mode 
are erased.
≥A locked file cannot be erased.
≥If there are many files in a card, it takes 
several minutes for deleting.
STILL
ENTERFA D E
MENU
i s
(14)
PHOTO
SHOT(47)
STILL
ENTERFA D E
MENU
i s
(14)
Formatting a Card 
If a Card becomes unreadable by the Camcorder, 
format it for reuse. Formatting erases all the data 
recorded on a Card.
1Set [PICTURE/MPEG4 PLAYBACK MENU] 
>> [EDITING] >> [CARD FORMAT] >> [YES]. 
([MPEG4 PLAYBACK MENU] on PV-GS200 
Model only)
≥A confirmation message appears, select 
[YES] and formatting will be carried out.
≥When the formatting is completed, the screen 
becomes white.
≥It may not be possible to use a Card formatted 
by this Camcorder on another unit. In this case, 
format the Card on the unit which will be using 
the Card. Make sure that valuable pictures are 
stored on PC before proceeding.
≥A Card formatted on other equipment (e.g. PC) 
might be unusable or it might take more time for 
recording. We recommend that you use this 
equipment to format the Card.
STILL
ENTERFA D E
MENU
i s
(14)
FORMAT WILL DELETE
ALL FILES
  ;:NO ---  RETURN
  ∫:YES
CARD FORMAT
!:ENTER     MENU:EXIT
PV-GS120_200Eng.book  49 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Playback Mode
-50-
Enlarging a Movie Picture Size
(PV-GS200 only)
You can enlarge a Moving Picture to full screen 
size
1Set [MPEG4 PLAYBACK MENU] >> 
[DISPLAY] >> [SCREEN] >> [FULL].
Display specifications in playing back MPEG4 
moving pictures
[NORMAL] display
≥Pictures equal to or smaller than QCIF 
(176k144) are expanded to twice as large as 
the original size.
≥Pictures larger than QCIF pictures (176k144) 
are displayed as large as the original size.
[FULL] screen display
≥Pictures equal to or larger than QCIF 
(176k144) are displayed in full screen.
≥Pictures smaller than QCIF pictures (176k144) 
are expanded about 3.6 times as large as the 
original size.
≥When setting to [FULL], pictures may be shown 
in mosaic-like pattern depending on the file.
To Resume Normal Moving Picture SizeSet [MPEG4 PLAYBACK MENU] >> [DISPLAY] 
>> [SCREEN] >> [NORMAL].
STILL
ENTERFA D E
MENU
i s
(14)
MPEG4MOL-001.ASF
MPEG4MOL-001.ASF
Playing Back on Your TV
By connecting your Camcorder to your TV, the 
recorded scenes can be viewed on your TV 
screen.
≥Before connecting them, turn off the power of 
both the Camcorder and TV.
1Connect the [AV IN/OUT] Jack of the 
Camcorder and the Video and Audio Input 
Jacks of the TV.
≥Connect to the TV with the AV Cable 1. If the 
TV has an S-Video Jack, connect the S-Video 
Cable 2, too.
≥Plug the AV Cable as shown 3 so that the 
cord hangs down.
≥When plugging the pin plug of the AV cable 
into the [AV IN/OUT] Jack, plug it in as far as 
it goes.
To Make the Indications Appear on the TV 
Screen
Press the [OSD] Button (58) on the Remote 
Controller.
≥For other notes concerning this item, see 
-77-. 
1 2
[VIDEO IN]
[AUDIO IN] [S-VIDEO IN]
AV IN/OUT
PHONES
S-VIDEO
IN/OUTDV
3
ZOOM
OSD
DISPLAY
DATE/
TIME
RESET
TITLE
PHOTO
SHOTSTART/
STOP(58)
PV-GS120_200Eng.book  50 ページ  ２００４年２月１６日　月曜日　午後１時３２分