Panasonic Pv Gs120 Operating Instructions Manual

							Before Use
-11-
ªRecording a Still Picture on a Card 
(Photoshot)
1
Set the Mode Dial to Card Recording Mode.
2Press the [PHOTO SHOT] Button.
ªRecording a Moving Picture on a Card 
(MPEG4) (PV-GS200 only)
1
Set the Mode Dial to Card Recording Mode.
2Press the Recording Start/Stop Button.
3Press the Recording Start/Stop Button 
again to pause the recording.
ªPlaying Back a Tape
1Set the [OFF/ON] Switch 1 to [ON].
≥The [POWER] Lamp 2 lights up.
2Set the Mode Dial to Tape Playback Mode.
3Press the [6] Button to rewind the tape.
PCSD
PHOTO
SHOT
PCSD
POWER
1 2
ONOFF
PCSD
ENTERFA D E
STILL
i s
4Press the [1] Button to start playback.
5Press the [∫] Button to Stop Playback.
ªPlaying Back a CardIt plays back files recorded on a Card.1Set the Mode Dial to Picture Playback Mode 
or MPEG4 Playback Mode. (MPEG4 
Playback Mode on PV-GS200 Model only)
2Start Playback.
[PICTURE]:
1: Starting the Slide Show
5: Playing back the next picture
6: Playing back the previous picture
∫: Stop the Slide Show
;: Pause the Slide Show
[MPEG4] (PV-GS200 only):
1: Playing back the File
5: Selecting the next file (When you tap this 
button during playback, you can search the 
next file, and when you keep pressing it, cue 
playback is activated.)
6: Selecting the previous file (When you tap 
this button during playback, you can search 
the beginning of the file, and when you keep 
pressing it, review playback is activated.)
∫: Stop playing back
;: Pause playing back
FA D E
STILL
ENTERi s
ENTERFA D E
STILL
i s
PC
SD
P
C
SD
PV-GS120_200Eng.book  11 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-12-
Before Use
Before Using
These operating Instructions are designed for use 
with models PV-GS120 and PV-GS200. Pictures 
may be slightly different from the original.
≥The illustrations used in these Operating 
Instructions show model PV-GS200, however, 
parts of the explanation refer to different 
models.
≥Depending on the model, some functions are 
not available.
≥Features may vary, so please read carefully.
Standard Accessories
Illustrated are accessories supplied with the 
Camcorder.
1) AC Adaptor, DC Cable and AC Cable 
-16-
2) Battery Pack -16-3) Remote Controller and Button-Type 
Battery -15-4) Magic Wire Remote Control with Narration 
Mic (PV-GS200 only) -15-≥If you wish to operate PV-GS120 with a 
Magic Wire Remote Control with Narration 
CAUTION:This unit will operate on 110/120/220/240 V 
AC. An AC plug adaptor may be required for 
voltages other than 120 V AC. Please 
contact either a local or foreign electrical 
parts distributor for assistance in selecting 
an alternate AC plug. We recommend using 
the accessory power plug adaptor 
(VJSS0070) in an area which has special AC 
outlets.
CR2025
VYF2973 K2KC4CB00009
VFA0425
N2QAGC000018 CGA-DU14 
(PV-GS200)VSB0470
(PV-GS120)
PV-DAC14D K2GJ2DZ00017 K2CA2EA00005
N2QCBD000030
(PV-GS200)
1)
2)
5) 4)
7)
8) 9)6)
VFC3506
3)
Mic, Please refer to page -88- for 
replacement parts number.
5) Lens Cap and Lens Cap Cord 
-18-6) AV Cable -50-7) Shoulder Strap -18-8) SD Memory Card -19-9) USB Connection Kit (USB Cable and 
CD-ROM) -56-
Controls and Components
ªCamcorder
(1)Smart Accessory Shoe
≥The Video DC Light (optional), Video Flash 
(not supplied) or the Stereo Zoom 
Microphone (optional), etc. can be attached 
here. Power is supplied directly from the 
Camcorder when using an accessory 
supported by the Smart Accessory Shoe. 
(PV-GS200 only)
≥Do not touch the connector part of the 
Smart Accessory Shoe. (PV-GS200 only)
(2)LCD Monitor Open Button [PUSH OPEN] -20-
(3)LCD Monitor -20-,-81-
(4)
Card Slot Cover -19-
(5)Card Slot -19-
(6)Card Slot Cover Open Lever [OPEN] -19-
(7)
Recording Check Button [S] -27-Recording Button [REC] -53-
(8)Backlight Button [BACK LIGHT] -33-,-53-
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the LCD Monitor screen. 
However, this is not a malfunction and does 
not affect the recorded picture.
(2)  (3) (1)
(4)
(5)
(6)
MULTI/
P-IN-PSTILL
ENTERFA D E
SOFT
SKINTELE
MACRO
SDCARD
MENUPUSHCLOSE
RECBACK LIGHT
ACCESS
i s
MAGIC
PIX
(10) (11)   (12)    (13) 
(14)    (15)(16)(17)(18)(19) (7)
(8)
(9)
PV-GS120_200Eng.book  12 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-13-
(9)Card Access Lamp [ACCESS] -19-
(10)Multi Button [MULTI] -40-Picture-in-Picture Button [P-IN-P] -40-
(11)MagicPix Button [MAGICPIX] -34-
(12)Soft Skin Button [SOFT SKIN] -34-
(13)Tele Macro Button [TELE MACRO] -32-
(14)Menu Button [MENU] -21-
(15)Pause Button [;] -45-Still Button [STILL] -28-
(16)Fast Forward/Cue Button [5] -42-,-45-
(17)Play Button [1] -42-,-45-Enter Button [ENTER] -21-
(18)Stop Button [∫] -42-,-45-Fade Button [FADE] -33-
(19)Rewind/Review Button [6] -42-,-45-
(20)
Built-in Flash (PV-GS200 only) -38-
(21)Flash Open Lever [ßL] (PV-GS200 only) -38-
(22)Lens Hood -81-
(23)Lens (LEICA DICOMAR)
≥LEICA is a registered trademark of Leica 
microsystems IR GmbH and DICOMAR is a 
registered trademark of Leica Camera AG.
(24)Focus Ring (PV-GS200 only) -38-
(25)Eyecup(26)Power LCD Button [POWER LCD] -21-Power LCD Lamp -21-
(27)Recording Lamp -27-
(28)Microphone (built-in, stereo) -32-,-34-
(29)White Balance Sensor -36-Remote Control Sensor -15-
(30)Lock Button -17-
(31)Lock Cover -17-
(32)
USB Jack [ ] -57-
(33)Jack for Magic Wire Remote Control with 
Narration Mic [REMOTE] (PV-GS200 only) 
-28-Microphone Jack [MIC]
(20) (21) (22) (23) (24) 
(25)
(26)
(30)
(31)
  (27) (28) (29)
AV IN/OUT 
PHONES
REMOTE/MIC(PLUG IN POWER)
(32)
(33)
(34)(35) (36) (37) (38)
≥When connecting an external microphone 
or audio equipment to this jack, the built-in 
microphone does not operate.
≥When connecting the Magic Wire Remote 
Control with Narration Mic to this jack and 
the [TALK] Button is pressed, the built-in 
microphone does not operate. (PV-GS200 
only) 
-28-≥When connecting the pin plug of the Magic 
Wire Remote Control with Narration Mic to 
this jack, plug it in as far as it goes. 
(PV-GS200 only)
≥A compatible plug-in powered microphone 
can be used. Please consult your dealer for 
more information.
≥The microphone may make noises 
depending on the type used. In this case, 
we recommend using the battery with the 
Camcorder to reduce noises instead of the 
AC adaptor.
(34)Audio-Video Input/Output Jack 
[AV IN/OUT] -50-Headphone Jack [PHONES]
≥Connecting an AV Cable to this jack 
activates the Camcorder’s built-in speaker, 
but connecting a headphone, etc. 
deactivates it.
≥When connecting the pin plug of the AV 
Cable to this jack, plug it in as far as it goes.
≥When using headphones, set [AV JACK] of 
the [AV IN/OUT] or [INITIAL] sub-menu to 
[OUT/PHONES]. If you set [AV JACK] to 
[OUT], you may hear noises on the right.
(35)Mode Selector Switch 
[AUTO/MANUAL/FOCUS] -27-,-35-,-38-
(36)Reset Button [RESET] -70-
(37)Speaker -42-
(38)Cassette Eject Lever [OPEN/EJECT] -18-
(39)
Mode Dial -19-
(40)Quick Start Recording Button 
[QUICK START] -31-Quick Start Recording Lamp -31-
(41)Power Lamp [POWER] -19-,-27-,-42-
(42)Recording Start/Stop Button -27-,-30-
(43)Power Switch [OFF/ON] -19-,-27-,-42-,-78-
(44)Cassette Holder
PC
SD
ONOFF
POWER
PCSD
PV-GS200 PV-GS120
STARTQUICK(40)
(41)
(42)
(43)(46)
(47) (44)
(45) (39)
PV-GS120_200Eng.book  13 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-14-
(45)Cassette Compartment Cover -18-
(46)Zoom Lever [W/T],
Volume/Jog Lever [`VOL/JOG_] -31-,-42-
(47)Photoshot Button [PHOTO SHOT] -28-,-51-
(48)
Eyepiece Corrector Knob -20-
(49)Viewfinder -20-,-81-
(50)
Battery Eject Button [PUSH BATT] -16-
(51)Battery Holder(52)Shoulder Strap Holders -18-
(53)Grip Belt (One-touch Free Style Grip Belt) -17-
(54)Tripod Receptacle
≥Used for mounting the Camcorder on an 
optional tripod.
(55)DV Terminal [DV] -53-≥Connect this to the digital video equipment.(56)S-Video Input/Output Jack 
[S-VIDEO IN/OUT] -50-
ªRemote ControllerUsing the wireless Remote Controller that is 
supplied with the Camcorder, most of the 
Camcorder functions can be operated from a 
distance.
(57)Date/Time Button [DATE/TIME] -69-
(58)Indication Output Button [OSD] -50-
(59)Display Button [DISPLAY] -69-
(60)Reset Button [RESET] -84-
Due to limitations in LCD production 
technology, there may be some tiny bright or 
dark spots on the Viewfinder screen. 
However, this is not a malfunction and does 
not affect the recorded picture.
S-VIDEO
IN/OUTDV
(48)(49)
 (50) (51) (52) (53)
(54)
(55)
  (56)
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP. B . D I G I TA L
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM
(57)
(58)
(59)
(60)(61)
(62)
(63)(61)
Recording Button [¥REC] -53-
(62)Audio Dubbing Button [A.DUB] -51-
(63)Direction Buttons for Playback Zoom 
Function [π,∑,∏,∫] -45-
(64)
Slow Motion/Still Advance Buttons [E,D] 
(E: Reverse, D:Forward) -43-
(65)Index Search Buttons [:,9] 
(:: Reverse, 9:Forward) -44-
(66)Selection Button [SELECT] -45-
(67)Store Button [STORE] -45-
(68)Off/On Button [OFF/ON] -45-
(69)Zoom/Volume Button [ZOOM/VOL] -31-,-42-,-44-
(70)Variable Speed Search Button 
[VAR. SEARCH] -43-
(71)Menu Button [MENU] -21-
(72)
Photoshot Button [PHOTO SHOT] -28-,-51-
(73)Title Button [TITLE] -48-
(74)Multi-Picture/Picture-in-Picture Button 
[MULTI/P-IN-P] -40-,-46-
(75)Rewind/Review Button [6] -42-,-45-
(76)Pause Button [;] -43-,-45-
(77)Stop Button [∫] -42-,-45-
(78)Recording Start/Stop Button 
[START/STOP] -27-,-30-
(79)Play Button [1] -42-,-45-
(80)Fast-forward/Cue Button [5] -42-,-45-
(81)Playback Zoom Button [P.B. ZOOM] -44-
(82)Enter Button [ENTER] -21-
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM(64)
(65)
(66)
(67)
(68)(69)
(70)
(71)
ZOOM
INDEX INDEXSELECTSTORESTOP
KL∫
OSDDISPLAY
V/REWSTILL ADV
OFF/ONP.B.DIGITAL
DATE/
TIME
RESET
TITLE T
WsVOLr¥RECMULTI/
P-IN-PPHOTO
SHOTSTART/
STOP
A.DUB
PLAY
PAU S EFF /WSTILL ADV
ENTER61 5;ED
VA R .
SEARCHMENU
P.B. ZOOM
(72)
(73)(78)
(81)
(82) (79)
(80) (74)
(75)
(76)
(77)
PV-GS120_200Eng.book  14 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-15-
ªMagic Wire Remote Control with 
Narration Mic (PV-GS200 only)
This controller allows the scene to be shot from 
various angles, high to low, and is also 
convenient when a Tripod is used. When the 
controller is not in use, attach the clip to the Grip 
Belt for convenience.
This controller makes it easier for left-handed 
users to use the Camcorder.
(83)Microphone [MIC] -28-
(84)Recording Start/Stop Button [REC](85)Zoom Lever [W/T]
≥Zoom speed changes in 2 stages.
(86)Photoshot Button [PHOTO SHOT](87)Microphone Switch Button [TALK] -28-≥When the Magic Wire Remote Control with 
Narration Mic is connected to [REMOTE] 
Jack and the [TALK] Button is pressed, the 
narration microphone is activated and the 
built-in microphone on the Camcorder is 
deactivated.
(88)Clip
≥Insert the plug securely into the [REMOTE] 
Jack as far as it will go. A loose connection 
will affect normal operation.
The Remote Controller
ªInserting a Button-type BatteryBefore using the Remote Controller, insert the 
supplied button-type battery.
1While pressing the Lock Button 1, pull out 
the Battery Holder.
2Insert the button-type battery with the (i) 
marking facing upwards.
3Insert the Battery Holder into the Remote 
Controller.
(83)
(84)
(85)
(86)
(87)(88)
1
≥When the button-type battery is exhausted, 
replace it with a new CR2025 battery. (A battery 
is normally expected to last about 1 year. 
However, it depends on operation frequency.)
≥Make sure to match the poles correctly when 
inserting the battery.
ªUsing the Remote Controller
1Direct the Remote Controller at the Remote 
Control Sensor (29) of the Camcorder and 
press an appropriate button.
≥Distance from the Camcorder: Within 
approximately 15 feet (5 meters)
≥Angle: Within approximately 10o in the 
upward, and 15o in the downward and 
horizontal directions from the central axis
≥The above operating ranges are for indoor use. 
Outdoors or under strong light, the Camcorder 
may not operate properly even within the above 
ranges.
≥Within a 3 feet (1 meter) range, you can also 
use the Remote Controller on the LCD Monitor 
side of the Camcorder.Warning
Danger of explosion if battery is 
incorrectly replaced.
Replace only with the same or equivalent 
type recommended by the equipment 
manufacturer. Discard used batteries 
according to manufacturer’s instructions.
Risk of fire, explosion and burns. Do not 
recharge, disassemble, heat above 212°F 
(100°C) or incinerate. Keep the 
Button-Type battery out of the reach of 
children. Never put Button-Type battery 
in mouth. If swallowed, call your doctor.
Replace battery with Panasonic PART NO. 
CR2025 only. Use of another battery may 
present a risk of fire or explosion.
Caution: Battery may explode if mistreated.
Dispose of used battery promptly. Keep 
away from children. 
Do not recharge, disassemble or dispose of 
in fire.
10
1515 15(29)
PV-GS120_200Eng.book  15 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-16-
Selecting Remote Controller Modes
When 2 Camcorders are used simultaneously, 
they can be operated individually by selecting 
different Remote Controller Modes.
≥If the Remote Controller Mode of the 
Camcorder and that of the Remote Controller 
do not match, [REMOTE] Indication is 
displayed.
Setup on the Camcorder:Set [REMOTE] on the [INITIAL] Sub-Menu to the 
desired Remote Controller Mode. (-23-)
Setup on the Remote Controller:
[VCR1]: Press the [D] Button and [∫] Button 
simultaneously. 1
[VCR2]: Press the [E] Button and [∫] Button 
simultaneously. 2
≥When the battery in the Remote Controller is 
replaced, the mode is automatically reset to 
[VCR1] Mode.
Power Supply
ªUsing the AC Adaptor
1
Connect the DC Cable to the Camcorder.2Connect the DC Cable to the AC Adaptor.3Connect the AC Cable to the AC Adaptor 
and the AC Jack.
≥The AC Cable’s outlet plug does not fit 
entirely into the AC Adaptor jack. A gap will 
remain as shown 1.
≥Before connecting or disconnecting the 
power supply, set the [OFF/ON] Switch on 
the Camcorder to [OFF] and make sure that 
[POWER] Lamp is not lit.
INDEX INDEX
SELECT
STOPKL∫
STILL ADV
T
W
PA U S ESTILL ADV61 5
;EDP.B. ZOOM21
1
ªUsing the BatteryBefore use, fully charge the Battery.
≥We recommend using a Panasonic Battery.
≥We cannot guarantee the quality of this 
Camcorder when batteries from other 
companies are used.
1Attach the Battery to the AC Adaptor and 
charge it.
≥Since the Battery will not be charged when 
the DC Cable is connected to the AC 
Adaptor, disconnect it from the AC Adaptor.
≥The [CHARGE] Lamp lights up, and charging 
starts.
≥When the [CHARGE] Lamp goes off, 
charging is completed.
≥When the battery is completely discharged, 
the [CHARGE] lamp blinks at first, but the 
battery is charged normally. When the 
temperature of the battery is too high or low, 
the [CHARGE] lamp blinks and the charging 
time becomes longer than usual.
2Attach the charged Battery to the 
Camcorder.
Disconnecting the Power SourceSet the [OFF/ON] Switch (43) to [OFF] and, while 
pressing the [PUSH BATT] Button (50), slide the 
Battery or DC Cable upward to disconnect it.
≥For other notes concerning this item, see 
-71-.
PUSH
BATT
ONOFF
(50)
(43)
PV-GS120_200Eng.book  16 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							
Before Use
-17-
Charging Time and Available 
Recording Time
PV-GS200
PV-GS120
ACharging Time
B Maximum Continuous Recording Time
≥ “1h30min.” indicates 1 hour and 30 minutes.
≥ Battery CGA-DU14 is supplied. (PV-GS200 
only)
≥ Battery VSB0470 is supplied. (PV-GS120 only)
≥ The times shown in the table are approximate 
times. The numbers indicate the recording time 
when the Viewfinder is used. The numbers in 
parentheses indicate the recording time when 
the LCD Monitor is used. In actual use, the 
available recording time may be shorter.
≥ The times shown in the table are for continuous 
recording at a temperature of 68 oF (25 oC) and 
humidity of 60%. If the Battery is charged at a 
higher or lower temperature, the charging time 
may be longer.
≥ We recommend the Battery Pack VSB0470 
(PV-GS120 only), CGA-DU14 and CGA-DU21 
for long time recording (2 hours or more for 
continuous recording, 1 hour or more for 
intermittent recording).
≥ In the following cases, the available recording 
time becomes shorter.
≥ You use the Viewfinder and LCD Monitor 
simultaneously when using the 0 Lux 
MagicPix function, rotating the LCD Monitor 
forward to record yourself.
≥ When you set [EVF ON/AUTO] to [ON].
≥ When you use the Camcorder while lighting 
the LCD Monitor up by pressing the 
[POWER LCD] Button.
≥ When you use accessories applicable to the 
Smart Accessory Shoe (Stereo Zoom 
Microphone, Video DC Light, etc.). 
(PV-GS200 only)
CGA-DU14A2h45min.
B2h30min.(2h10min.)CGA-DU21A3h55min.B3h45min.(3h15min.)
CGA-DU07A1h30min.B1h15min.(1h5min.)
VSB0470A2h10min.B2h25min.(2h5min.)
CGA-DU14A 2h45min.
B3h.(2h40min.)CGA-DU21A 3h55min.B4h30min.(4h.)
CGA-DU07A1h30min.B1h30min.(1h20min.)
The One-touch Free Style Grip Belt
ªTo Use as a Grip BeltAdjust the length of the Grip Belt to the size of 
your hand.
1Detach the end of the Grip Belt.
2Adjust the length of the Grip Belt to the size 
of your hand.
3Reattach the Grip Belt.
ªTo Use as a Hand StrapUsing the Grip Belt as the hand strap makes it 
easier to handle and carry a Camcorder. It is 
more convenient to use with the Magic Wire 
Remote Control with Narration Mic (PV-GS200 
only).
1Open the Lock Cover (31) by holding the 
tabs on both sides  1, press the Lock 
Button 
(30) and detach the Grip Belt.
2Detach the end of the Grip Belt.
1(31) (30)
PV-GS120_200Eng_text.fm  17 ページ  ２００４年２月１７日　火曜日　午前１１時５４分 
						

							Before Use
-18-
3Slide A in the direction of the arrow and 
reattach the Grip Belt.
4Attach the Grip Belt around your wrist.
≥When returning the Grip Belt to the Grip Belt 
Attachment, press the Lock Cover 2 to ensure 
that it is securely locked.
Attaching the Lens Cap
To protect the Lens surface, attach the Lens Cap.1Pass the end of the Lens Cap Cord through 
the hole in the Grip Belt Attachment part 
and the Lens Cap through the Lens Cap 
Cord.
≥The removed Lens Cap can be hooked onto the 
Grip Belt. (It is not possible when using as a 
hand strap.)
≥When you are not recording, be sure to cover 
the Lens with the Lens Cap for protection.
A
2
Attaching the Shoulder Strap
We recommend that you attach the Shoulder 
Strap before going out to avoid dropping the 
Camcorder.
1Pull the end of the Shoulder Strap through 
the Shoulder Strap Holder (52) on the 
Camcorder.
2Fold the end of the Shoulder Strap, run it 
through the Shoulder Strap Length 
Adjuster, and pull it.
≥Pull it out more than 1 inch (2 cm) 1 from the 
Shoulder Strap Length Adjuster so that it 
cannot slip off.
≥Attach the other end of the Shoulder Strap to 
the other Shoulder Strap Holder in the same 
way.
Inserting a Cassette
1Slide the [OPEN/EJECT] Lever (38) toward 
the front and pull down to open the 
Cassette Compartment Cover.
2Insert a Cassette.
3Close the Cassette Holder by pressing the 
[PUSH] mark 1.
4Close the Cassette Compartment Cover.
1
OPEN/
EJECT
(38)
PUSH
1
PV-GS120_200Eng.book  18 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							Before Use
-19-
ªAccidental Erasure PreventionOpening the accidental erasure prevention slider 
1 on the cassette (by sliding it to the [SAVE] 
arrow direction) prevents recording. To enable 
recording, close the accidental erasure 
prevention slider (by sliding it to the [REC] arrow 
direction).
≥For other notes concerning this item, see 
-71-.
Using a Memory Card
A Card can be used to record pictures.
≥Use a genuine SD Memory Card or 
MultiMediaCard manufactured by Panasonic 
only.
Before inserting or removing a Card, be sure 
to turn off the Camcorder.
≥Otherwise, the Camcorder may not function 
properly or it may cause the loss of recorded 
data in a Card.
ªInserting a Card
1Slide the [OPEN] Lever (6) to open the Card 
Slot Cover (4).
2While holding the Memory Card with its cut 
corner on top 1, insert it into the Card Slot.
3Close the Card Slot Cover (4) securely.
Removing the Card
Open the Card Slot Cover and then pull the Card 
straight out.
≥After removing the Card, close the Card Slot 
Cover.
R E CSAVE
1
OPEN(6)(4)
1
ª[ACCESS] Lamp (9)
While the Camcorder is accessing the Card 
(reading, recording, playback or erasing), the 
[ACCESS] Lamp lights up.
≥While the [ACCESS] Lamp is on, never attempt 
to open the Card Slot Cover, to pull out the 
Card, to turn off the Camcorder. Such actions 
will damage the Card, and recorded data, and 
cause the Camcorder to malfunction.
Turning on the Camcorder 
When the Camcorder is turned on with the Lens 
Cap on, the Automatic White Balance Adjustment 
may not function properly. Please turn on the 
Camcorder after removing the Lens Cap.
ªHow to Turn on the Power
1Set the [OFF/ON] Switch (43) to [ON] while 
pressing the button 1.
≥The [POWER] Lamp 
(41) lights up.
ªHow to Turn off the Power
1Set the [OFF/ON] Switch (43) to [OFF] while 
pressing the button 1.
Selecting Modes
You can choose a desired mode by rotating the 
Mode Dial.
1Rotate the Mode Dial (39).
:Tape Recording Mode
Use this mode when recording pictures on a tape.
Also, you can record still pictures on the card 
simultaneously during recording on a tape.
ACCESS(9)
ONOFF
POWER
1
(41)
(43)
ONOFF(43)1
PCSD(39)
PV-GS120_200Eng.book  19 ページ  ２００４年２月１６日　月曜日　午後１時３２分 
						

							
Before Use
-20-
:Tape Playback Mode
Use this mode when playing back the recorded 
scene on a tape. :Card Recording Mode
Use this mode when recording a still picture or a 
moving picture on a card. (moving picture on 
PV-GS200 Model only) :Picture Playback Mode
Use this mode when playing back the recorded 
still picture on a card. :MPEG4 Playback Mode (PV-GS200 only)
Use this mode when playing back the recorded 
moving picture on a card. :PC Mode
Use this mode when you want to connect the 
Camcorder to your Personal Computer.
Using the Viewfinder/LCD Monitor
ª Using the ViewfinderBefore using the Viewfinder, adjust the field of 
view so that the displays inside the Viewfinder 
become clear and easy to read.
1Tilt up the Viewfinder.
≥The Viewfinder can also be pulled out for use.
≥ Do not pull on the Eyecup to extend the 
Viewfinder.
2Adjust by sliding the Eyepiece Corrector 
Knob (48).
To Use the Viewfinder at the Same Time as the 
LCD Monitor
Set [LCD/EVF] >> [EVF ON/AUTO] >> [ON].
≥ The Viewfinder does not turn off even if the LCD 
Monitor is opened.
≥ When you turn the Camcorder off, this setting is 
cancelled.
ª Using the LCD MonitorWith the LCD Monitor open, you can also record 
the picture while watching it.
1Press the [PUSH OPEN] Button (2) and pull 
the LCD Monitor (3) out in the direction of 
the arrow.
≥ The Viewfinder is now deactivated.
PC
12:30:45PM
OCT 15 200412:30:45PM
OCT 15 200412:30:45PM
OCT 15 2004
12:30:45PM
OCT 15 2004
(48)
≥
The LCD Monitor can be opened a maximum 
of 120 o. If you open the LCD monitor to an 
angle of 120 o, it becomes easier to operate 
menus or to play back pictures.
2Adjust the LCD Monitor angle according to 
the desired recording angle.
≥ The LCD Monitor can rotate a maximum of 
180 o 1  from the vertical position upwards 
and a maximum of 90 o 2  to the downward 
direction. Forcefully rotating the LCD Monitor 
beyond these ranges will damage the 
Camcorder. You cannot rotate the LCD 
Monitor when it is opened to an angle of 120 o. 
Therefore, do not rotate it forcibly.
Closing the LCD MonitorPush the LCD Monitor until it is securely locked.
≥ Make sure the Card Slot Cover is closed.
ª Adjusting Brightness and Color LevelWhen [LCD/EVF SET] on the [LCD/EVF] 
Sub-Menu is set to [YES], the following items are 
displayed.
LCD Brightness [LCD BRIGHTNESS]
Adjusts the brightness of the image on the LCD 
screen.
LCD Color Level [LCD COLOR LEVEL]
Adjusts the color saturation of the image on the 
LCD screen.
Brightness of the Viewfinder 
[EVF BRIGHTNESS]
Adjusts the brightness of the image in the 
Viewfinder.
To Adjust
Press the [ ;/∫ ] Button and select the item to be 
adjusted, and then press the [ 6/5 ] Button to 
raise or lower the number of vertical bars in the 
Bar Indication.
PUSHOPEN
(2)        (3)
2 90 o
1 180 o
1LCD BRIGHTNESS
    [-]||||----[+]
 LCD COLOR LEVEL
    [-]||||----[+]
 EVF BRIGHTNESS
    [-]||||----[+]
  ;/∫:SELECT  &/% :SETUP
             !/MENU:EXIT
LCD/EVF SETUP
PV-GS120_200Eng_text.fm  20 ページ  ２００４年２月１７日　火曜日　午後３時９分