Panasonic Matrix Switcher Wj Sx550c Operating Instructions

85
4
Alarm Recall
There are 99 alarm records stored in chronological order in 7 pages of tables.
The tables also show all monitor numbers involved when Alarm Mode-3 is activated, and indicate the alarm mode number
when Alarm Mode-1 or Alarm Mode-2 is activated.
Press the Function F1button to select the next page. Press the Function F2button to back up to the previous page.
Note:The Alarm column lists the following:
0:Camera Site Alarm with corresponding Camera number.
1:Alarm Board Input with alarm...

System Menu
As shown below, the system menu allows access to six items.
To select an item from the System Menu:
1. Select the desired item by moving the Joystick Controller.
2. To execute the selection, press the CAM (SET)key.
The selected menu appears on the monitor.
3. To return to the Set Up Menu, press the MON (ESC)key.
Controller (Controller-Monitor Partitioning)
This table is used to prevent specific WV-CU550C System controllers from ever controlling the outputs of specific monitors.
This feature...

87
4
EXT (External) Timing Select
This table permits the sequence dwell time on the selected monitor to be synchronized with the time lapse mode set in the
associated Time Lapse VCR.
To program or edit the EXT Timing Select Table, do the following:
1. Move the cursor to position 3 by moving the Joystick Controller, then press the CAM (SET)key.
2. Move the cursor to the desired monitor position by moving the Joystick Controller.
Press the Function F4button to open the Pop Up Window. Select EXT On or Off...

88
4
Compensation/VD2
This table is used to select a cable length for cable loss compensation, and to turn the vertical drive sync signal (VD2) and the
control data for the cameras on or off.
To program or edit the Compensation/VD2 Table, do the following:
1. Move the cursor to position 3 by moving the Joystick Controller, then press the CAM (SET)key.
2. Move the cursor to position 4 by moving the Joystick Controller.
Press the INC +1CAMbutton or DEC –1CAMbutton repeatedly to select the most suitable...

89
4
RS-485 Site Communication
This table is used to set the parameters for communication between the Data Boards installed in the Matrix Switcher and the
Camera Site.
To program or edit the RS-485 Communication Table, do the following:
1. Move the cursor to position 3 by moving the Joystick Controller.
Enter the desired data board number (1-8) by pressing the Numeric key, then press the CAM (SET)key.
2. Move the cursor to position 4 by moving the Joystick Controller.
Press the Function F4Button to open...

Communication Speed
This table is used to set the parameters for communication between the System Controllers (or PCs) and the Matrix Switcher.
To program or edit the Communication Speed Table, do the following:
1. Move the cursor to  position 3 by moving the Joystick Controller, then press the CAM (SET)key.
2. Move the Cursor to position 4 by moving the Joystick Controller.
Press the Function F4button to open the Pop Up Window. Select the desired Baud Rate by moving the Joystick Controller,
and then...

91
4
Clock Set
This table is used to set the current time and date.
To program or edit the Clock Set Table, do the following:
1. Move the cursor to position 3 by moving the Joystick Controller, then press the CAM (SET)key.
2. Move the cursor to position 4 by moving the Joystick Controller.
Press the Function F4button to open the Pop Up Window.
Select the desired month by moving the Joystick Controller, and then press the CAM (SET)key to execute the selection.
3. Move the cursor to position 5 by moving...

92
4
Auto Cleaning
Auto Cleaning is for cleaning the electric-mechanical contacts of the Panasonic combination cameras.  Use this function for
maintenance when the camera has been directed at the same spot or panned over the same range for a long time.
This table is used to enable and disable the auto cleaning function of the specified combination cameras at a user-specified
time or date.
To program or edit the Auto Cleaning Table, do the following:
1. Move the cursor to position 2 by moving the...

93
4
•Display of Cleaning Result
Cleaning proceeds in the order of the camera numbers, starting with the lowest number.
The table shows the cleaning result for the cameras (position 8).
= : Cleaning is completed.
]: Cleaning is disabled.
Note:While either manually or timer controlled cleaning is in progress, the camera controlled manually or automatically
from the system is disabled cleaning.
•Manual Cleaning
Move the cursor to position 3 and select Manual, then press theCAM (SET)key to execute cleaning...

95
5
SECTION 5
OPERATING
PROCEDURES